EN 61000-6-7-2015 en Electromagnetic compatibility (EMC) - Part 6-7 Generic standards - Immunity requirements for equipment intended to perform functions in a safety-related system.pdf

1、BSI Standards PublicationElectromagnetic compatibility (EMC)Part 6-7: Generic standards Immunity requirements for equipment intended to perform functions in a safety-related system (functional safety) in industrial locationsBS EN 61000-6-7:2015National forewordThis British Standard is the UK impleme

2、ntation of EN 61000-6-7:2015. It isidentical to IEC 61000-6-7:2014.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/210, EMC - Policy committee.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not pu

3、rport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 73863 0ICS 33.100.20Compliance with a British Standard cannot confer immunity fromlegal obligati

4、ons.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61000-6-7:2015EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 61000-6-7 May 2015 ICS 33.100

5、.20 English Version Electromagnetic compatibility (EMC) - Part 6-7: Generic standards - Immunity requirements for equipment intended toperform functions in a safety-related system (functional safety) in industrial locations (IEC 61000-6-7:2014) Compatibilit lectromagntique (CEM) - Partie 6-7:Normes

6、gnriques - Exigences dimmunit pour lesquipements visant exercer des fonctions dans un systme li la scurit (scurit fonctionnelle) dans dessites industriels (IEC 61000-6-7:2014) Elektromagnetische Vertrglichkeit (EMV) - Teil 6-7: Fachgrundnormen - Strfestigkeitsanforderungen an Gerte und Einrichtungen

7、, die zur Durchfhrung von Funktionen insicherheitsbeszogenen Systemen (funktionale Sicherheit) an industriellen Standorten vorgesehen sind (IEC 61000-6-7:2014) This European Standard was approved by CENELEC on 2014-11-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations

8、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. T

9、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN

10、ELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherl

11、ands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centr

12、e: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61000-6-7:2015 E EN 61000-6-7:2015 - 2 - Foreword The text of document 77/462/FDIS, future edition 1 of IEC 61000-6-7, prepared by IEC/TC 77 “

13、Electromagnetic compatibility“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61000-6-7:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop

14、) 2015-11-08 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-11-13 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for iden

15、tifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61000-6-7:2014 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IE

16、C 60204-1:2005 and A1:2008 NOTE Harmonized as EN 60204-1:2006 (modified) and EN 60204-1:2009/A1:2009 (not modified) IEC 61000-6-2:2005 NOTE Harmonized as EN 61000-6-2:2005 (not modified). IEC 61326-1:2012 NOTE Harmonized as EN 61326-1:2013 (not modified). IEC 61508-2 NOTE Harmonized as EN 61508-2. I

17、EC 61508-4:2010 NOTE Harmonized as EN 61508-4:2010 (not modified). IEC 61511 NOTE Harmonized in EN 61511 series (not modified). IEC 61784-3 NOTE Harmonized in EN 61784-3 series (not modified). IEC 62061:2005 NOTE Harmonized as EN 62061:2005 (not modified). ISO 13849-1:2006 NOTE Harmonized as EN 1384

18、9-1:2008 (not modified). ISO 13849-2:2012 NOTE Harmonized as EN 13849-2:2012 (not modified). BS EN 61000-6-7:2015- 3 - EN 61000-6-7:2015 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part

19、, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been m

20、odified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60050 series International Electrotechnical Vo

21、cabulary - - IEC/TS 61000-1-2 2008 Electromagnetic compatibility (EMC) - Part 1-2: General - Methodology for the achievement of functional safety of electrical and electronic systems including equipment with regard to electromagnetic phenomena - - IEC 61000-1-6 2012 Electromagnetic compatibility (EM

22、C) - Part 1-6: General - Guide to the assessment of measurement uncertainty - - IEC 61000-4-2 - Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test EN 61000-4-2 - IEC 61000-4-3 - Electromagnetic compatibility (EMC) - Part 4-3: Te

23、sting and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test EN 61000-4-3 - IEC 61000-4-4 - Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test EN 61000-4-4 - IEC 61000-4-5 - Electroma

24、gnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test EN 61000-4-5 - IEC 61000-4-6 - Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields EN 61000-4-6 - BS

25、EN 61000-6-7:2015EN 61000-6-7:2015 - 4 - Publication Year Title EN/HD Year IEC 61000-4-8 - Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test EN 61000-4-8 - IEC 61000-4-11 - Electromagnetic compatibility (EMC) - Part 4-11

26、: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests EN 61000-4-11 - IEC 61000-4-16 - Electromagnetic compatibility (EMC) - Part 4-16: Testing and measurement techniques - Test for immunity to conducted, common mode disturbances in the freque

27、ncy range 0 Hz to 150 kHz EN 61000-4-16 - IEC 61000-4-29 - Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests EN 61000-4-29 - IEC 61000-4-34 - Electromagnetic compatibi

28、lity (EMC) - Part 4-34: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with mains current more than 16 A per phase EN 61000-4-34 - IEC 61508 series Functional safety of electrical/electronic/programmable electronic safety-re

29、lated systems EN 61508 series IEC 61784-3 - Industrial communication networks - Profiles - Part 3: Functional safety fieldbuses - General rules and profile definitions EN 61784-3 - IEC Guide 107 - Electromagnetic compatibility - Guide to the drafting of electromagnetic compatibility publications - -

30、 BS EN 61000-6-7:2015 2 IEC 61000-6-7:2014 IEC 2014 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope and object . 7 2 Normative references 7 3 Terms, definitions and abbreviations . 8 3.1 Terms and definitions 8 3.2 Abbreviations 12 4 General . 13 4.1 Conformance to IEC Guide 107 . 13 4.2 Conformance

31、to IEC/TS 61000-1-2 . 13 4.3 Strategy for the availability of functions intended for safety applications . 14 5 Performance criteria 14 5.1 Performance criterion for functional safety applications . 14 5.2 Application of the performance criterion DS 15 6 Test plan . 15 6.1 General . 15 6.2 Configura

32、tion of EUT during testing 15 6.2.1 General . 15 6.2.2 Composition of EUT . 16 6.2.3 Assembly of EUT . 16 6.2.4 I/O ports 16 6.2.5 Auxiliary equipment . 16 6.2.6 Cabling and earthing (grounding) . 16 6.3 Operational conditions of EUT during testing 16 6.3.1 Modes . 16 6.3.2 Environmental conditions

33、. 16 6.3.3 EUT application software during test 16 6.4 Specification of functional performance . 17 6.5 Test description 17 6.6 Test performance 17 6.6.1 General . 17 6.6.2 Aspects to be considered during application of DS 17 7 Immunity requirements 18 8 Test setup and test philosophy 25 8.1 Test se

34、tup . 25 8.2 Test philosophy. 26 8.3 Test configuration . 26 8.4 Monitoring . 27 9 Test results and test report 27 Annex A (informative) Strategy for functions intended for safety applications . 28 Bibliography 29 Figure 1 Equipment ports . 11 BS EN 61000-6-7:2015IEC 61000-6-7:2014 IEC 2014 3 Table

35、1 Reaction of EUT during test 18 Table 2 Immunity test requirements for equipment Enclosure port . 19 Table 3 Immunity test requirements for equipment Input and output AC power ports . 20 Table 4 Immunity test requirements for equipment Input and output DC power ports . 21 Table 5 Immunity test requ

36、irements for equipment I/O signal/control ports 22 Table 6 Immunity test requirements for equipment I/O signal/control ports connected directly to AC power supply networks (including functional earth ports) 23 Table 7 General frequency ranges for mobile transmitters and ISM equipment for radiated te

37、sts 24 Table 8 General frequency ranges for mobile transmitters and ISM for conducted tests . 25 Table 9 Applicable performance criteria and observed behaviour during test for equipment within the scope that is intended for use in safety-related systems 26 BS EN 61000-6-7:2015 4 IEC 61000-6-7:2014 I

38、EC 2014 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTROMAGNETIC COMPATIBILITY (EMC) Part 6-7: Generic standards Immunity requirements for equipment intended to perform functions in a safety-related system (functional safety) in industrial locations FOREWORD 1) The International Electrotechnical

39、Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end

40、and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Commit

41、tee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in acco

42、rdance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all in

43、terested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held respo

44、nsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergenc

45、e between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks

46、 of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts

47、and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publi

48、cation or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publi

49、cation may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61000-6-7 has been prepared by TC 77: Electromagnetic compatibility. The text of this standard is based on the following documents: FDIS Report on voting 77/462/FDIS 77/468/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. Thi