EN 61158-2-2014 en Industrial communication networks - Fieldbus specifications - Part 2 Physical layer specification and service definition.pdf

1、BSI Standards PublicationIndustrial communication networks Fieldbus specificationsPart 2: Physical layer specification and service definitionBS EN 61158-2:2014National forewordThis British Standard is the UK implementation of EN 61158-2:2014. It is identical to IEC 61158-2:2014. It supersedes BS EN

2、61158-2:2010 which is withdrawn.The UK participation in its preparation was entrusted to Technical Com-mittee AMT/7, Industrial communications: process measurement andcontrol, including fieldbus.A list of organizations represented on this committee can be obtained onrequest to its secretary.This pub

3、lication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 79255 7ICS 25.040.40; 35.100.10; 35.240.50Compliance with a British Standard

4、 cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61158-2:2014EUROPEAN STANDARDNORME EUROPENNEEUR

5、OPISCHE NORMEN 61158-2 October 2014 ICS 25.040; 35.100; 35.240.50 Supersedes EN 61158-2:2010 English Version Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition (IEC 61158-2:2014) Rseaux de communication industriels - Spcification

6、s des bus de terrain - Partie 2: Spcification et dfinition desservices de la couche physique (CEI 61158-2:2014) Industrielle Kommunikationsnetze - Feldbusse - Teil 2:Spezifikation und Dienstfestlegungen des Physical Layer(Bitbertragungsschicht) (IEC 61158-2:2014) This European Standard was approved

7、by CENELEC on 2014-08-21. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national s

8、tandards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own lan

9、guage and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fran

10、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Nor

11、malisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61158-2:2014 E EN 61158-2:2014 - 2 - F

12、oreword The text of document 65C/758A/FDIS, future edition 6 of IEC 61158-2, prepared by SC 65C “Industrial networks“ of IEC/TC 65 “Industrial-process measurement, control and automation“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61158-2:2014. The following dates a

13、re fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-05-21 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-08-21 This document supers

14、edes EN 61158-2:2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CENELEC

15、 by the European Commission and the European Free Trade Association. Endorsement notice The text of the International Standard IEC 61158-2:2014 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for

16、 the standards indicated: IEC 60079-0 NOTE Harmonized as EN 60079-0. IEC 60875-1 NOTE Harmonized as EN 60875-1. IEC 60947-5-2 NOTE Harmonized as EN 60947-5-2. IEC 61158 NOTE Harmonized as EN 61158 series. IEC 61158-1:2014 NOTE Harmonized as EN 61158-1:2014 (not modified). IEC 61158-4-1:2014 NOTE Har

17、monized as EN 61158-4-1 1)(not modified). IEC 61158-4-4:2014 NOTE Harmonized as EN 61158-4-4 1)(not modified). IEC 61158-4-7:2007 NOTE Harmonized as EN 61158-4-7:2008 (not modified). IEC 61158-4-8:2007 NOTE Harmonized as EN 61158-4-8:2008 (not modified). IEC 61158-4-12:2014 NOTE Harmonized as EN 611

18、58-4-12 1)(not modified). 1) To be published BS EN 61158-2:2014- 3 - EN 61158-2:2014 IEC 61158-4-16:2007 NOTE Harmonized as EN 61158-4-16:2008 (not modified). IEC 61158-4-18:2010 NOTE Harmonized as EN 61158-4-18:2012 (not modified). IEC 61158-4-20:2014 NOTE Harmonized as EN 61158-4-20 1)(not modifie

19、d). IEC 61158-4-24:2014 NOTE Harmonized as EN 61158-4-24 1)(not modified). IEC 61300-3-4 NOTE Harmonized as EN 61300-3-4. IEC/TR 61491 NOTE Harmonized as CLC/TR 61491. IEC 61596 NOTE Harmonized as EN 61596. IEC 61784-1 NOTE Harmonized as EN 61784-1. IEC 61784-2 NOTE Harmonized as EN 61784-2. BS EN 6

20、1158-2:2014EN 61158-2:2014 - 4 - Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated refer

21、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date infor

22、mation on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60050 series International Electrotechnical Vocabulary (IEV) - - IEC 60079-11 - Explosive atmospheres - Part 11: Equipment protection by intrinsic saf

23、ety “i“ EN 60079-11 - IEC 60079-14 - 2007 - Explosive atmospheres - Part 14: Electrical installations design, selection and erection EN 60079-14 + AC 2008 2011 IEC 60079-25 - Explosive atmospheres - Part 25: Intrinsically safe electrical systems EN 60079-25 - IEC 60169-17 - Radio-frequency connector

24、s Part 17: R.F. coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with screw coupling - Characteristic impedance 50 ohms (Type TNC) - - IEC 60189-1 2007 Low-frequency cables and wires with PVC insulation and PVC sheath - Part 1: General test and measuring methods - - IEC 60

25、255-22-1 1988 Electrical relays - Part 22: Electrical disturbance tests for measuring relays and protection equipment - Section 1: 1 MHz burst disturbance tests - - IEC 60364-4-41 - Low-voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock HD 60364-4

26、-41 - BS EN 61158-2:2014- 5 - EN 61158-2:2014 Publication Year Title EN/HD Year IEC 60364-5-54 - Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors HD 60364-5-54 - IEC 60529 - Degrees of protection provid

27、ed by enclosures (IP Code) EN 60529 - IEC 60603-7-4 - Connectors for electronic equipment - Part 7-4: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz EN 60603-7-4 - IEC 60754-2 - Test on gases evolved during combustion of m

28、aterials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity EN 60754-2 - IEC 60793 series Optical fibres EN 60793 series IEC 60793-2-30 2012 Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres EN 60793-2-30 20

29、13 IEC 60793-2-40 2009 Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres EN 60793-2-40 2011 IEC 60794-1-2 2003 Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures EN 60794-1-2 2003 IEC 60807-3 - Rect

30、angular connectors for frequencies below 3 MHz - Part 3: Detail specification for a range of connectors with trapezoidal shaped metal shells and round contacts - Removable crimp types with closed crimp barrels, rear insertion/rear extraction - - IEC 60811-403 - Electric and optical fibre cables - Te

31、st methods for non-metallic materials - Part 403: Miscellaneous tests - Ozone resistance tests on cross-linked compounds EN 60811-403 - IEC 60811-404 2012 Electric and optical fibre cables - Test methods for non-metallic materials - Part 404: Miscellaneous tests - Mineral oil immersion tests for she

32、aths EN 60811-404 2012 IEC 61000-4-2 - Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test EN 61000-4-2 - IEC 61000-4-3 - Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-freque

33、ncy, electromagnetic field immunity test EN 61000-4-3 - BS EN 61158-2:2014EN 61158-2:2014 - 6 - Publication Year Title EN/HD Year IEC 61000-4-4 - Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test EN 61000-4-4 - IEC 6113

34、1-2 2007 Programmable controllers - Part 2: Equipment requirements and tests EN 61131-2 2007 IEC 61156-1 2007 Multicore and symmetrical pair/quad cables for digital communications - Part 1: Generic specification - - IEC 61158-3-20 2014 Industrial communication networks - Fieldbus specifications - Pa

35、rt 3-20: Data-link layer service definition - Type 20 elements EN 61158-3-20 2014 IEC 61158-4-2 2014 Industrial communication networks - Fieldbus specifications - Part 4-2: Data-link layer protocol specification - Type 2 elements EN 61158-4-2 2)IEC 61158-4-3 2014 Industrial communication networks -

36、Fieldbus specifications - Part 4-3: Data-link layer protocol specification - Type 3 elements EN 61158-4-3 2) IEC 61169-8 2007 Radio-frequency connectors - Part 8: Sectional specification - RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock - Characterist

37、ics impedance 50 ohms (type BNC) EN 61169-8 2007 IEC 61210 (mod) 2010 Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements EN 61210 2010 IEC 61754-2 - Fibre optic connector interfaces - Part 2: Type BFOC/2,5 connector family EN 61754-2 - IEC 617

38、54-13 - Fibre optic connector interfaces - Part 13: Type FC-PC connector EN 61754-13 - IEC 61754-22 - Fibre optic connector interfaces - Part 22: Type F-SMA connector family EN 61754-22 - ISO/IEC 7498 series Information technology - Open Systems Interconnection - Basic Reference Model - - ISO/IEC 74

39、98-1 1994 Information technology - Open Systems Interconnection - Basic Reference Model: The Basic Model - - ISO/IEC 8482 - Information technology - Telecommunications and information exchange between systems - Twisted pair multipoint interconnections - - 2) To be published. BS EN 61158-2:2014- 7 -

40、EN 61158-2:2014 Publication Year Title EN/HD Year ISO/IEC 8802-3 - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access met

41、hod and physical layer specifications - - ISO/IEC 10731 1994 Information technology - Open Systems Interconnection - Basic Reference Model - Conventions for the definition of OSI services - - ISO 4892-1 - Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance EN ISO 48

42、92-1 - ISO 9314-1 - Information Processing Systems - Fibre distributed data interface (FDDI) - Part 1: Token Ring physical layer protocol (PHY) - - ANSI TIA/EIA-422-B - Electrical Characteristics of Balanced Voltage Digital Interface Circuits - - ANSI TIA/EIA-485-A - Electrical Characteristics of Ge

43、nerators and Receivers for Use in Balanced Digital Multipoint Systems - - ANSI TIA/EIA-644-A - Electrical Characteristics of Low Voltage Differential Signaling (LVDS) Interface Circuits - - BS EN 61158-2:2014 2 IEC 61158-2:2014 IEC 2014 CONTENTS 0 Introduction 32 0.1 General . 32 0.2 Physical layer

44、overview . 32 0.3 Document overview . 32 0.4 Major physical layer variations specified in this standard . 33 0.4.1 Type 1 media . 33 0.4.2 Type 2: Coaxial wire and optical media 33 0.4.3 Type 3: Twisted-pair wire and optical media 33 0.4.4 Type 4: Wire medium . 34 0.4.5 Type 8: Twisted-pair wire and

45、 optical media 34 0.4.6 Type 12: Wire medium . 34 0.4.7 Type 16: optical media 34 0.4.8 Type 18: Media 34 0.4.9 Type 20: Media 35 0.4.10 Type 24: Media 35 0.5 Patent declaration . 35 1 Scope . 36 2 Normative references . 36 3 Terms and definitions . 38 Common terms and definitions 38 3.1Type 1: Term

46、s and definitions . 43 3.2Type 2: Terms and definitions . 46 3.3Type 3: Terms and definitions . 49 3.4Type 4: Terms and definitions . 52 3.5Void 53 3.6Type 8: Terms and definitions . 53 3.7Type 12: Terms and definitions . 56 3.8Type 16: Terms and definitions . 57 3.9Type 18: Terms and definitions .

47、60 3.10Type 24: Terms and definitions . 61 3.11Type 20 terms and definitions 63 3.124 Symbols and abbreviations . 66 Symbols 66 4.1Type 1: Symbols 66 4.1.1Type 2: Symbols 67 4.1.2Type 3: Symbols 68 4.1.3Void . 68 4.1.5Type 8: Symbols 68 4.1.6Type 12: Symbols 69 4.1.7Type 16: Symbols 69 4.1.8Type 18:

48、 Symbols 69 4.1.9Type 24: Symbols 70 4.1.10Type 20: symbols 70 4.1.11Abbreviations 70 4.2Type 1: Abbreviations 70 4.2.1BS EN 61158-2:2014IEC 61158-2:2014 IEC 2014 3 Type 2: Abbreviations 71 4.2.2Type 3: Abbreviations 72 4.2.3Type 4: Abbreviations 74 4.2.4Void . 74 4.2.5Type 8: Abbreviations 74 4.2.6

49、Type 12: Abbreviations 75 4.2.7Type 16: Abbreviations 76 4.2.8Type 18: Abbreviations 76 4.2.9Type 24: Abbreviations 77 4.2.10Type 20: Abbreviations 77 4.2.115 DLL PhL interface 77 General . 77 5.1Type 1: Required services . 78 5.2Primitives of the PhS . 78 5.2.1Notification of PhS characteristics . 79 5.2.2Transmission of Ph-user-data 80 5.2.3Reception of Ph-user-data . 80 5.2.4Type 2: Required services . 80 5.3General . 80 5.3.1M_symbols 80 5.3.2PH-LOCK indication . 81 5.3.3PH-FRAME indication 81 5