EN 61169-36-1997 en Radio-Frequency Connectors Part 36 Sectional Specification for Microminiature r f Coaxial Connectors with Snap-On Coupling - Characteristic Impedance 50 ohm (Ty.pdf

1、 STD-BSI BS EN bLLbS-3b-ENGL 1777 1b2LibbS b13093 02 m BRITISH STANDARD Radio-frequency connectors Part 36. Microminiature r.f. coaxial connectors with snap-on coupling - Characteristic impedance 50 (type MCX) * * cri The European Standard EN 61169-36 : 1997 has the status of a British Standant ICs

2、33.120.30 BS EN 61169-36 : 1997 EC 1169-36 ; 1996 - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that annex

3、ZA lists nonnative references to international publications with their corresponding European publications. The British Standards which implement these international or European pubiications may be found in the BSI standards Catalogue under the section entitied International Standards Correspondence

4、 Index, or using the Fnd facility of the BSI Standards Elecimnic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN titie page, pages 2 to 27, a blank page, an

5、inside back cover and a back cover. STD-BSI BS EN bLLb7-3b-ENGL 1797 m Lb24bb9 0b33075 b85 m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61 169-36 May 1997 ICs 33.120.30 Desriptors: Ebctronic componente, microminiature r.f. oonnactors, snapon coupng, impdanw 50 ohm English version Radio-f r

6、equency connectors Patt 36: Sectional specification for microminiature r.f. coaxial connectors with snap-on coupling - Characteristic impedance 50 ohm (type MCX) (IEC 1 169-3611 996) Connecteurs pour frquences Hochfrequenz-Steckverbinder radiolectriques Teil 36: Rahmenspezifikation fr Partie 36: Spc

7、ification intermdiaire pour les connecteurs microminiatures coaxiaux pour frquences encliquetage - Impdance caractristique 50 ohm (type MCX) Microminiatur HF-Koaxialsteckverbinder mit Einrastkupplung - Wellenwiderstand 50 Ohm (Typ MCX) radiolectriques accouplement par (IEC 1 169-36: 1 996) (CE1 1 16

8、9-36:1996) This European Standard wbs approved by CENELEC on 1997-03-1 1. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibli

9、ographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions English, French, German). A version in any other language made by translation under the responsibility

10、 of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlan

11、ds, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Biusseis 1997 CENELE

12、C - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. NO. EN 61 169-36:1997 E Page 2 EN 61169-36 : 1997 Foreword lhe text of the International Standard IEC 1 169-36:1996, prepared by SC 460, RF connectors, of IEC TC 46, Cables, wires, waveguides, R.

13、F. connectors, and accessories for communication and signalling, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 61 169-36 on 1997-03-1 1 without any modification. lhe following dates were fixed: - latest date by which the EN has to be implemented at national level

14、 by publication of an identical national standard or by endorsement (dop) 1998-03-01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-03-01 This part 36 of EN 61 169 is to be used in conjunction with EN 61 169-1 :1994 and its amendment Al : 1996.

15、Endorsement notice The text of the International Standard IEC 1 169-36:1996 was approved by CENELEC as a European Standard without any modification. - STD-BSI BS EN bLlb9-3b-ENGL 1797 1b29bb7 b33077 458 Page 3 EN 61169-36 : 1997 CONTENTS General . 1.1 Scope . 1.2 Normative references . 1.3 IEC type

16、designation Mating face and gauge information . 2.1 Dimensions for general purpose connectors . 2.2 Gauges for general purpose connectors . 2.3 Dimensions for standard test connedors (grade O) Quality assessment procedure 3.1 General 3.2 Ratings and characteristics (see clause 6 of IEC 1169-1, QC 22

17、0000) 3.3 Test schedule and inspection requirements - type MCX 3.4 Instructions for preparation of detail specifications 3.5 Blank detailspecification pro forma for series MCX connectors Annex ZA (normative) Normative references to international publications with their corresponding European publica

18、tions . . . . 4 4 4 4 4 4 7 9 11 11 11 14 17 18 27 STD-BSI BS EN bLLb7-3b-ENGL 1997 1b24bb9 Ob33098 39q Page 4 EN 61169-36 ; 1997-. - RADIO-FREQUENCY CONNECTORS - Part 36: Microminiature r.f. coaxial connectors with snap-on coupling - Characteristlc impedance 50 f2 (type MCX) i General 1.1 Scope Thi

19、s part of IEC 1169 concerns microminiature coaxial connectors for use with flexible and semi-rigid r.f. cables (96 IEC 50-1- . and 96 IEC 50-2- .). These connectors have a snapsn coupling mechanism, 50 i2 impedance, an operating frequency range of 3 GHt and are known commercially as MCX connectors.

20、1.2 Nonnative references The following normative documents contain provisians which, through reference in this text, constitute provisions of this part of IEC 1169. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreemen

21、ts based on this part of IEC 11 69 are encouraged to investigate the possibility of . applying the most recent editions of the normative documents indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC 96-2: 1988, Radio-frequency cables - Patt 2: R

22、elevant cable specifications IEC 1169-1 : 1992, Radio-frequency connectors - Part 1: Gene grade 2 = general purpose connector = 02. c) A group of figures specifying the climatic category. Example: 1169-56 IEC 02 (55/155/21) denotes a grade 2 connector, with coupling details as indicated in figures 1

23、 and 2, climatic category 55/155/21. 2 Mating fuce und gauge infomution 2.1 Metric dimensions are original dimensions. Ail undimensioned pictorial configurations are for reference purposes only. Dimensions for general purpose Connectors STD*BSI BS EN blLb9-3b-ENGL 1997 Lb24bb9 Ob33079 220 Page 5 EN

24、61169-36 : 1997 A 8 C O E F 0 H I K 1 M N O P Ri 2.1 .I Plug 0,019 0,079 - 0.110 0,110 0.163 - 0,120 0.006 O.Oo0 - - - - - - 3 0,021 Diunotu - Dimeter - 4 Dimeter 0.151 Dimeter 0,126 - - 1 - 2 Dimeter nominal 2 Diameter 0.010 DiMl0t.f 0.012 0.1 18 5 Diuneter 0.142 6 Dkmetu 0,041 - - Flgure 1 - Gener

25、al purpose plug Table 1 - Dimensions of plug h I 1 Form nd dinwnrkn of 0ut.r contact detent to meet ekotrk.l and 2 Dimeter of contra conductor and of uniform rrursmisrion liw to give roquird ch.noterirtic impkn? of bo P. 3 Number and dimonsknr d tkts to meet droMorl Md.mechaniai -B. 4 0p.Cnd to 3,s

26、mm (0,lS in) diuneter muimum lo meet gauc require- mmb. 5 Dimeter chosan to mort mochuiical ind dectrical requirements and to oompenrrte for electrid effect of riou. 6 Priarbpdottinuidfluing. me0hMkd UtWWnb. STD-BSI BS EN bLLbS-Ib-ENGL 1797 - - 0,142 0,135 0.001 0.102 0.167 0.090 - Page 6 EN 61169-3

27、6 : 1997 - 0,078 0.140 0.197 0.1 10 0.110 0,162 0,033 - B I I I =i A B C 0 E F o H I K L O P Lb24bb7 Ob33100 72 Figure 2 - General purpose socket Table 2 - Dimensions of socket 2.80 4.00 4.12 0.75 0.85 9,OS nominai - - 3.80 h I 2 Diameter Diuneter Diunetor Diame b) the connector series deslgnation.

28、The specification miter should enter the details relating to the connector styk/variant(s) to be covered as indicated. The numbers In brackets In the BDS correspond to the folbwing indications which shall be ghren. 3.4.2 Identf.ication of the detail spectticatlon 1) The name of the National Authorza

29、d Institution (NAI) under whose authority the OS is published and, if applhxble, the organization from whom the OS Is available. 2) The number allocated to the DS by the relevant Natbnal Authorized Institution immediately preceded by the IS0 two letter national Identity code or “XX“ when the DS Is p

30、roduced by an IEC technkal sub-committee. 3) The number and Issue number of the IECQ generic spedflcation and, when applicable, the sedional specifkatbn; also the national reference if different. 4) if different from the IEC QC number, the national number of the DS, date of issue and any further inf

31、ormation required by the national system, together with any amendment numbers. 3.4.3 Identificaion of the component 5) Enter the following details: - style: the style deslgnatlon of the connector Including type of fixlng and sealing if applicable: - attachment: by deletion of the inapplicable option

32、s of cablelwire ghren for centre and outer conductors; - special features and markings: as applicable; - series designation: in bold charactersldigits approximately 15 mm hlgh. 6) Enter detalls of assessment level and the cllmatk category. 7) A reproduction of the outline drawlng and details of the

33、panel piercing (if applicable) It shall provide the maximum envelope dimensions, also the posltlon of the reference plane and, in the case of a fixed connector, the position of the mounting plane(s) both relative to the front face of the connector. Page 18 EN 61169-36 : 1997 Any maximum panel thickn

34、ess limitations for fixed connectors shall be stated. 8) Particulars of all variants covered by the OS. As appropriate, the information shall include: - cable types (or sizes) applicable to each variant; - alternative plated or protective finishes; - details of alternative mounting flanges having ei

35、ther tapped or plain mounting hobs; - details of alternative solder spills or solder buckets including, when applicable, those for um with microwave integrated circuit (MIC) components. 9.4.4 PenomnanCe 9) Perfomrance data listing the most important characteristics of the connector in accordance wit

36、h the requirements of the relevant sectional specification. Deviations from the mlnimum requirements shall be clearly indicated. Non-applicable parameters shall be marked “na“. 3.4.5 Maticing, ordering inbmtion and related mtters 10) Insert marking and ordering information as approprfate, together w

37、ith details of related documents and any invoked structural similarity. 3.4.6 Selection of tests, test wnditbns and severtties 11) -na shall be used to indicate nOfkapplkabl8 tests. All tests marked “a“ by the detail specification writer shall be mandatory. When using the normal procedure with a ded

38、icated BDS, the letter “a“ - for applicable - shall be entered in the “test reqUred“ column against each of the tests indicated as being mandatory in !he test schedule of the relevant sectional speclficatlon. Any additional tests required at the discretion of the specification writer shall also be i

39、ndicated by an .ag. The specification writer shall also indicate, when necessary, details of deviations fram the standard test methods and test conditions, Including any relevant deviatkns given in the test schedule of the sectional specification. The qualification approval and conformance inspectio

40、n shall be such that the NSI shall be satisfied that they are appropriate and in line with those for other connectors within the system providing a reasonably comparable sewice. 3.5 Blank detail specitk8tion pro forma for serles MCX connectors nie followlng pages contain the complete BDS. * m * SPEC

41、IflCAlWN OC 22W (IEC 116-1) SECTIONAL SPECIFICATION QC 22SWO (IEC 116Q-%) NATIOWAL REFERENCE Page 19 EN 61169-36 : 1997 (4) Issue I.“ “.“ (i) outlirw and muimum dimensbns Panel piercing and mounting doWls For mating Intorbca dlmonrions and poshion of roforan plan seo QC 223600 (IEC 1169-aS) Mubnum P

42、.MI thidoimr: tor iront mounting ._ .“ mm. for mar mounting “. mm (8) Vdutr olhor crible. VUkntNo. h8-h Of vuknt 96 IEC 41 . U m I“._. “.I_ . U“-. “-u. - - .“.I “.“+.“.“.U.-“ . . “I “.“I. . I . In.“.“ “U-“ . “._.“. . “.“.“.“W“. . “.“ “ “.“ . “ “.“U . .-. I “.“ . .“I. . .U“ “ “.I. . “U . . “.I.“. . I

43、 “I. .n. “ . “ Insott Is0 nrsion idrntity cede or XX If completed by IEC oommltteo. - STD-BSI BS EN bLLb7-3b-ENGL 1777 LbZ4bbS Ob33LlV 3b7 W Page 20 EN 61169-36 : 1997 (S) Performance (including limiting conditions of use) RiWngs 8nd chwmmftticr MC81 Nombril impedina Freq-cy woe Vuknt No. brig- Rdl?

44、tbl ketor 41 .“. .“ . W -. centro tontact mirtante cenb. 0Ondur;Dr 41 “.“ -. continuity “.“U“. “.I“. .“I“. outeroonductor Inrul8tion rerirtuici voltige pioof 41 .I“. u se8-l.vel “ . W“. “.I. Pmef Vdt.04 u 4.4 kP8 .Ititude 41 .“ “. . “U. “. -. .“I“. Envhonmrtil t.st uolrago* 8tslta.hl 41 “.“ . “ “I“

45、“.I . Environmentai test Vdtageat UkPa -01 I“ 8ltmdo .“I. . I. .“ “ “. 41 .I . “.“I. sapenbig eff4veri.rr .U- “ .“ . Dirdrirgewst (-ml (d) t test required (if technically applicable); AQL I 0spt.ble q.Citv 1-1 . I dertruotive tests - rpedmens shall not be returned to stock. Quality conformance inspe

46、ction tof-by-fof tests This shall conslst of test groups Al and B1 on a lot-by-lot basis. QuaMkatbn approval and ifs maintenance This shall consist of three consecutive lots passing test groups At and 81 followed by selection of specimens from the lots as appropriate. These specimens shall successfu

47、lly pass the specified periodic D tests. Page 27 EN 61169-36 : 1997 Annex ZA (normative) Nonnative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These norm

48、ative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated refe

49、rences the latest edition of the publication referred to applies (including amendments). NOTE: When an international publication has been modifid by common modifications, indicated by (mod), the relevant ENMD applies. Publication Year IEC 96-2 1988 IEC 1169-1 1992 QC O01 005 1994 - Title ENIHD - Year Radio-frequency cables - Part 2: Relevant cable specifications (corrigendum 1993) Radio-frequency connectors EN 61 169-1 1994 Part 1 : Generic specification - General requirements and measuring methods