EN 61169-38-2009 en Radio-frequency connectors - Part 38 Sectional specification - Radio frequency coaxial connectors model slide-in (rack and panel applications) - Characteristic .pdf

1、Radio-frequency connectors Part 38: Sectional specification Radio frequencycoaxial connectors model, slide-in (rack and panelapplications) Characteristic impedance 50T(type TMA) 50T applicationsBS EN 61169-38:2009raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COP

2、YRIGHT LAWBSI British StandardsNational forewordThis British Standard is the UK implementation of EN 61169-38:2009. It isidentical to IEC 61169-38:2008. It supersedes DD IEC/PAS 61169-38 which iswithdrawn.The UK participation in its preparation was entrusted by Technical CommitteeEPL/46, Cables, wir

3、es and waveguides, radio frequency connectors and accessories for communication and signalling, to Subcommittee EPL/46/2,Radio frequency connectors and waveguides.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to inc

4、lude all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2009ISBN 978 0 580 58678 1ICS 33.120.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy

5、 and Strategy Committee on 30 April 2009Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61169-38:2009EUROPEAN STANDARD EN 61169-38 NORME EUROPENNE EUROPISCHE NORM March 2009 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisa

6、tion Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: avenue Marnix 17, B - 1000 Brussels 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-38:2009 E ICS 33.120.20 English version Rad

7、io-frequency connectors - Part 38: Sectional specification - Radio frequency coaxial connectors model, slide-in (rack and panel applications) - Characteristic impedance 50 (type TMA) - 50 applications (IEC 61169-38:2008) Connecteurs pour frquences radiolectriques - Partie 38: Spcification intermdiai

8、re - Connecteurs coaxiaux pour frquences radiolectriques avec accouplements de type glis (applications de “panneau“ et “fond de panier“) - Impdance caractristique 50 (type TMA) - Applications 50 (CEI 61169-38:2008) Hochfrequenz-Steckverbinder -Teil 38: Rahmenspezifikation - Koaxiale Hochfrequenzstec

9、kverbinder mit Einschubkupplung (Einschubausfhrung) - Wellenwiderstand 50 (Typ TMA) - 50-Anwendungen (IEC 61169-38:2008) This European Standard was approved by CENELEC on 2008-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givi

10、ng this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official v

11、ersions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees

12、 of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Ki

13、ngdom. BS EN 61169-38:2009EN 61169-38:2009 2 Foreword The text of document 46F/75/CDV, future edition 1 of IEC 61169-38, prepared by SC 46F, R.F. and microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories, was sub

14、mitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61169-38 on 2008-12-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-09-01 latest date by whi

15、ch the national standards conflicting with the EN have to be withdrawn (dow) 2011-12-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61169-38:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 61169-38:2009 3 E

16、N 61169-38:2009 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referenc

17、es, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61169-1 1992 Radio-frequency connectors - Part

18、 1: Generic specification - General requirements and measuring methods EN 61169-1 1994 IEC QC 001005 - 1)IEC Quality assessment system for electronic components (IECQ) - Register of films, products and services approved under the IECQ system, including ISO 9000 - - 1) Undated reference. BS EN 61169-

19、38:2009 2 61169-38 IEC:2008(E) CONTENTS 1 Scope.6 2 Normative references .6 3 Mating face and gauge information.7 3.1 Dimensions General connectors Grade 2.7 3.1.1 Connector with pin centre contact (see Figure 1)7 3.1.2 Connectors with socket-centre contact (see Figure 2).8 3.2 Gauges .9 3.2.1 Conne

20、ctors with pin-centre contact9 3.2.2 Connectors with socket-centre contact 10 3.3 Dimensions standard test connectors Grade 0.11 3.3.1 Connector with pin-centre contact (see Figure 5).11 3.3.2 Connector with socket-centre contact (see Figure 6) .12 3.4 General requirements for connector mounting in

21、modules and on panels.14 3.4.1 Radial misalignment 14 3.4.2 Axial misalignment .14 4 Quality assessment procedure15 4.1 General .15 4.2 Rating and characteristics ( see Clause 6 of IEC 61169-1/QC220000) 15 4.3 Test schedule and inspection requirements .18 4.3.1 Acceptance tests (see Table 8)18 4.3.2

22、 Periodic tests (see Table 9) .19 4.4 Procedures20 4.4.1 Quality conformance inspection .20 4.4.2 Qualification approval and its maintenance20 5 Instructions for preparation of detail specifications .20 5.1 General .20 5.2 Identification of the detail specification 21 5.3 Identification of the compo

23、nent21 5.4 Performance21 5.5 Marking, ordering information and related matters.21 5.6 Selection of tests, test conditions and severities22 5.7 Blank detail specification pro-forma for type TMA connector23 Figure 1 Connector with pin-centre contact (for dimensions, see Table 1)7 Figure 2 Connector wi

24、th socket-centre contact (for dimensions, see Table 2) 8 Figure 3 Gauge for outer contact of pin connector (for dimensions, see Table 3) .9 Figure 4 Gauge pin for socket-centre contact (for dimensions, see Table 4).10 Figure 5 Standard test connector with pin-centre contact (for dimensions, see Tabl

25、e 5).11 Figure 6 Standard test connector with socket-centre contact (for dimensions, see Table 6) 12 Figure 7 The sketch map of connector radial misalignment 14 Figure 8 The sketch map of rigidly mounted and float-mounted connector14 Table 1 Dimensions of connector with pin-centre contact .7 BS EN 6

26、1169-38:200961169-38 IEC:2008(E) 3 Table 2 Dimensions of connector with socket-centre contact8 Table 3 Dimensions of gauge for outer contact of pin connector 9 Table 4 Dimensions of gauge pin for socket-center contact10 Table 5 Dimensions of standard test connector with pin-centre contact11 Table 6

27、Dimensions of standard test connector with socket-centre contact 13 Table 7 Rating and characteristics .15 Table 8 Acceptance tests.18 Table 9 Periodic tests 19 BS EN 61169-38:2009 6 61169-38 IEC:2008(E) RADIO-FREQUENCY CONNECTORS Part 38: Sectional specification Radio frequency coaxial connectors m

28、odel, slide-in (rack and panel applications) Characteristic impedance 50 (type TMA) 50 applications 1 Scope This part of 61169, which is a sectional specification, provides information and rules for the preparation of detail specifications for series TMA r.f. connectors together with the pro forma b

29、lank detail specification. Series TMA connectors have a characteristic impedance of 50 and are normally used with R.F cables or with microstrip in microwave fields that has a blind-entry and middle low-power. The connectors are usable up to a frequency of at least 6 GHz. This specification also pres

30、cribes mating face dimensions for general purpose connectors, dimensional details of standard test connectors grade 0, gauging information and tests selected from QC 220000 (IEC 61169-1), applicable to all detail specifications relating to series TMA connectors. This specification indicates the reco

31、mmended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated

32、 references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods IEC QC 001005, Register of firm

33、s, products and services approved under the IECQ system, including ISO 9000 BS EN 61169-38:200961169-38 IEC:2008(E) 7 3 Mating face and gauge information 3.0 General Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference purposes only. 3.1 Dimensions

34、General connectors Grade 2 3.1.1 Connector with pin centre contact (see Figure 1) Note 2 Note 3Note 1 g h i j k l e d f 1 455 65 b c Note 1IEC 1789/08 Figure 1 Connector with pin-centre contact (for dimensions, see Table 1) Table 1 Dimensions of connector with pin-centre contact mm inRef. min. max.

35、min. max. Notes a 0,64 0,025 Diameter b 1,32 1,37 0,052 0,054 Diameter c 2,06 2,21 0,081 0,087 Diameter d 4,83 0,190 Diameter e 2/ Diameter f 8,00 8,05 0,315 0,317 Diameter g 8,60 0,339 h 0,08 1,02 0,003 0,040 i 0,15 0,006 j 1,96 3,05 0,078 k 5,33 5,84 0,210 0,230 l 5,28 5,79 0,208 0,228 NOTE 1 Mech

36、anical and electrical reference plane. NOTE 2 MSlotted and flared to meet electrical and mechanical requirements. NOTE 3 MDesign and location of the sealing feature is optional but ensures the environmental performance requirements are met. BS EN 61169-38:2009 8 61169-38 IEC:2008(E) 3.1.2 Connectors

37、 with socket-centre contact (see Figure 2) o 35 40Note 3v w x z y Note 1 Note 2 aa p q r s t u IEC 1790/08 Figure 2 Connector with socket-centre contact (for dimensions, see Table 2) Table 2 Dimensions of connector with socket-centre contact mm inRef. min. max. min. max. Notes o 2/ Diameter p 2,06 2

38、,21 0,081 0,087 Diameter q 4,72 0,186 Diameter r 6,50 0,256 3/ Diameter s 8,10 8,15 0,319 0,321 Diameter t 10,00 10,15 0,394 0,400 Diameter u 12,3 12,4 0,484 0,488 Diameter v 4,78 5,28 0,188 0,208 w 4,72 5,23 0,186 0,206 x 4,95 0,195 y 0,15 0,006 z 8,31 8,51 0,327 0,335 aa 4 NOTE 1 Mechanical and el

39、ectrical reference plane. NOTE 2 Slotted and closed to meet electrical and mechanical requirements. NOTE 3 Applies only when dielectric extends beyond reference plane. NOTE 4 Radius BS EN 61169-38:200961169-38 IEC:2008(E) 9 3.2 Gauges 3.2.1 Connectors with pin-centre contact 3.2.1.1 Gauge for outer

40、contact of pin connector (see Figure 3) 35 40(aa)u s t z IEC 1791/08 Figure 3 Gauge for outer contact of pin connector (for dimensions, see Table 3) Table 3 Dimensions of gauge for outer contact of pin connector Gauge A (for sizing purposes) Gauge B (for measurement of gauge retention force for oute

41、r conductor) Mass of gauge(weight): 225 g 5 g Notes mm in mm inRef. min. max. min. max. min. max. min. max. s 8,08 8,10 0,318 0,319 8,15 8,18 0,321 0,322 Diameter t 10,00 10,15 0,394 0,400 10,00 10,15 0,394 0,400 Diameter u 12,4 0,488 12,4 0,488 Diameter z 8,41 8,46 0,331 0,333 8,36 8,41 0,329 0,331

42、 Diameter aa 0,8 0,031 0,8 0,031 2/ Radius NOTE 1 Material: steel, polished, surface roughness: Ra 0,4 m (16 in). NOTE 2 Parentheses indicate the reference size for size. 3.2.1.2 Test sequence Gauge A shall be placed over the outer electrical contact of the connector once. This is a sizing operation

43、 and should only be carried out when the insulator is removed from the connector. After this, gauge B shall be placed over the outer contact in a vertical position. The gauge shall be retained. This test can also be carried out on connectors when the insulator is not removed. BS EN 61169-38:2009 10

44、61169-38 IEC:2008(E) 3.2.2 Connectors with socket-centre contact 3.2.2.1 Gauge pin for socket-centre contact (see Figure 4) 4 mm max.(0,157 in max.) 3,17 mm min.(0,125 in min.)b IEC 1792/08Figure 4 Gauge pin for socket-centre contact (for dimensions, see Table 4) Table 4 Dimensions of gauge pin for

45、socket-center contact Gauge C (for sizing purpose) Gauge D (for measurement of gauge retention force for inner conductor) Mass (weight) of gauge: 57 g 1 g Note mm in mm inRef. min. max. min. max. min. max. min. max. b 1,372 1,377 0,054 0 0,0542 1,308 1,321 0,0515 0,052 0 Diameter Material: steel, po

46、lished , surface roughness: Ra 0,4 m (16 in). 3.2.2.2 Test sequence Test pin gauge C shall be inserted into the centre contact three times with a minimum distance of 3,17 mm (0,125 in). This is a sizing operation and should only be carried out when the socket-centre contact is removed from the conne

47、ctor. After this, gauge D shall be inserted and held in the vertical position. The gauge shall be retained. This test can also be carried out on connectors when the socket-centre contact is not removed. BS EN 61169-38:200961169-38 IEC:2008(E) 11 3.3 Dimensions standard test connectors Grade 0 3.3.1

48、Connector with pin-centre contact (see Figure 5) a 55 65Note 3 1 3 g 0,1 mm0,004 in A AAA 0,01 mm0,0005 in 0,1 mm 0,004 in 0,05 mm 0,002 in A0,05 mm0,002 in i j k l f n2n1d c m A B Note 1 Note 1 ab acNote 4 Note 5 Note 2 b c IEC 1793/08 Figure 5 Standard test connector with pin-centre contact (for dimensions, see Table 5) Table 5 Dimensions of standard test connector with pin-centre contact mm inRef. min. max. min. max. Notes a 0,64 0,025 Diameter b 1,35 1,37 0,053 0 0,054 1 Diameter c 2,140 nom. 0,084 2 nom. 2/ Diameter d 4,88 4,93 0,192 0,194 Diamete