EN 61169-48-2015 en Radio-frequency connectors - Part 48 Sectional specification for series BMP R F coaxial connectors.pdf

1、BSI Standards PublicationRadio-frequency connectorsPart 48: Sectional specification for series BMP R.F. coaxial connectorsBS EN 61169-48:2015National forewordThis British Standard is the UK implementation of EN 61169-48:2015. It isidentical to IEC 61169-48:2014.The UK participation in its preparatio

2、n was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all th

3、e necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 82917 8ICS 33.120.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standa

4、rd was published under the authority of theStandards Policy and Strategy Committee on 31 March 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61169-48:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61169-48 March 2015 ICS 33.120.30 English Versio

5、n Radio-frequency connectors - Part 48: Sectional specification for series BMP R.F. coaxial connectors (IEC 61169-48:2014) Connecteurs pour frquences radiolectriques - Partie 48: Spcification intermdiaire relative aux connecteurs coaxiaux R.F. srie BMP (IEC 61169-48:2014) Hochfrequenz-Steckverbinder

6、 - Teil 48: Rahmenspezifikation fr koaxiale HF Steckverbinder der BMP-Serie (IEC 61169-48:2014) This European Standard was approved by CENELEC on 2014-11-27. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

7、 the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (Englis

8、h, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of A

9、ustria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S

10、pain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights

11、of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61169-48:2015 E BS EN 61169-48:2015EN 61169-48:2015 - 2 - Foreword The text of document 46F/253/CDV, future edition 1 of IEC 61169-48, prepared by SC 46F “R.F. and microwave passive components“, of IEC/T

12、C 46 “Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61169-48:2015. The following dates are fixed: latest date by which the document has to be implemented at national leve

13、l by publication of an identical national standard or by endorsement (dop) 2015-09-13 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-11-27 Attention is drawn to the possibility that some of the elements of this document may be the subject of

14、 patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61169-48:2014 was approved by CENELEC as a European Standard without any modification. BS EN 61169-48:2015- 3 - EN 61169-48:20

15、15 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

16、applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions

17、of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60068-1 - Environmental testing - Part 1: General and guidance EN 60068-1 - IEC 61169-1 2013 Radio-frequency connectors - Part 1: Generic specification - General requirements and m

18、easuring methods EN 61169-1 2013 IEC 62037 series Passive RF and microwave devices, intermodulation level measurement EN 62037 series BS EN 61169-48:2015 2 IEC 61169-48:2014 IEC 2014 CONTENTS 1 Scope 6 2 Normative references 6 3 Mating face and gauge information 6 3.1 Dimensions General connectors G

19、rade 2 . 6 Connector with pin-centre contact Full detent and smooth bore 6 3.1.1Connector with socket-centre contact 7 3.1.23.2 Gauges . 8 Gauge pin for socket-centre contact 8 3.2.1Test procedure 9 3.2.2Gauge for outer contact of connector with pin-centre contact . 10 3.2.33.3 Dimensions Standard t

20、est connectors Grade 0 12 Connector with pin-centre contact 12 3.3.1Connector with socket-centre contact 13 3.3.23.4 General requirements for connector mounting on PCB 14 General . 14 3.4.1Maximum permitting deflexion . 15 3.4.2Maximum permitting axial clearance 15 3.4.34 Quality assessment procedur

21、e . 15 4.1 General . 15 4.2 Rating and characteristics (see Clause 5 of IEC 61169-1:2013) 15 4.3 Test schedule and inspection requirements Acceptance tests 18 Acceptance tests . 18 4.3.1Periodic tests . 19 4.3.24.4 Procedures for the quality conformance 20 Quality conformance inspection . 20 4.4.1Qu

22、ality conformance and its maintenance General procedure . 20 4.4.25 Instructions for preparation of detail specifications 20 5.1 General . 20 5.2 Identification of the component . 21 5.3 Performance . 21 5.4 Marking, ordering information and related matters 21 5.5 Selection of tests, test conditions

23、 and severities . 21 5.6 Blank detail specification pro-forma for type BMP connector . 22 6 Marking . 27 6.1 Marking of component . 27 6.2 Marking and contents of package 27 Figure 1 Connector with pin-centre contact 7 Figure 2 Connector with socket-centre contact . 8 Figure 3 Gauge pin for socket-c

24、entre contact . 9 Figure 4 Gauge A for sizing test . 10 Figure 5 Gauge B for retention test for pin connectors Full detent . 11 Figure 6 Gauge C for retention test for pin connectors Smooth bore . 12 Figure 7 Connector with pin-centre contact 13 BS EN 61169-48:2015IEC 61169-48:2014 IEC 2014 3 Figure

25、 8 Connector with socket-centre contact . 14 Figure 9 General requirements for connector mounting on PCB . 15 Table 1 Dimensions of connector with pin-centre contact . 7 Table 2 Dimensions of connector with socket-centre contact 8 Table 3 Dimensions of gauge pin for socket-centre contact 9 Table 4 G

26、auge A for sizing test 10 Table 5 Gauge B for retention test for pin connectors Full detent 11 Table 6 Gauge C for retention test for pin connectors Smooth bore . 12 Table 7 Dimensions of connector with pin-centre contact . 13 Table 8 Dimensions of connector with socket-centre contact 14 Table 9 Pre

27、ferred climatic categories (see IEC 60068-1) 16 Table 10 Rating and characteristics . 16 Table 11 Acceptance tests . 19 Table 12 Periodic tests 19 BS EN 61169-48:2015 6 IEC 61169-48:2014 IEC 2014 RADIO-FREQUENCY CONNECTORS Part 48: Sectional specification for series BMP R.F. coaxial connectors 1 Sco

28、pe This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series BMP RF coaxial connectors with blind mating, typically for use in 50 board to board connection. They may also be used with RF cables or micr

29、o-strips in microwave, telecommunication, wireless and other fields. Their operating frequency limit is up to 6 GHz. It describes the interface dimensions with gauging information, electrical and mechanical performance including the mandatory tests selected from IEC 61169-1:2013 applicable to all DS

30、 relating to type BMP connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers test schedules and inspection requirements. NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for refer

31、ence purpose only. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

32、including any amendments) applies. IEC 61169-1:2013, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods IEC 60068-1, Environmental testing Part 1: General and guidance IEC 62037 (all parts), Passive RF and microwave devices, intermodulation level meas

33、urement 3 Mating face and gauge information 3.1 Dimensions General connectors Grade 2 Connector with pin-centre contact Full detent and smooth bore 3.1.1The mating face of connector with pin-centre contact is shown in Figure 1 and its dimensions are shown in Table 1. BS EN 61169-48:2015IEC 61169-48:

34、2014 IEC 2014 7 (1) Mechanical and electrical reference plane. (2) The slots shall meet mechanical and electrical requirements. (3) The shape and size of outer conductor shall meet the electrical and mechanical performance requirements. (4) R0,2 recommended for fillet. Figure 1 Connector with pin-ce

35、ntre contact Table 1 Dimensions of connector with pin-centre contact Ref. mm Additional notes Min. Max. a 0,68 0,71 b 1,05 1,10 c 2,30 2,50 d a e 4,14 4,18 f 4,52 4,57 Full detent 4,23 4,28 Smooth bore g 1,77 2,02 h 0,00 0,25 i 2,62 j 0,42 0,52 Full detent 1,00 1,20 Smooth bore k 1,65 1,80 l 1,18 1,

36、28 m 45 2 Angle q 0,00 0,15 r 0,3 0,1 45 Chamfer aThe diameter is chosen upon the assumption that the PTFE dielectric has a dielectric constant of 2,02 to give an impedance of 50 . Connector with socket-centre contact 3.1.2The mating face of connector with socket-centre contact is shown in Figure 2

37、and its dimensions are shown in Table 2. IEC (1) (1) (2) (4) (3) BS EN 61169-48:2015 8 IEC 61169-48:2014 IEC 2014 (1) Mechanical and electrical reference plane. (2) Slotted and closed to meet electrical and mechanical requirements. Figure 2 Connector with socket-centre contact Table 2 Dimensions of

38、connector with socket-centre contact Ref. mm Additional notes Min. Max. a a b 1,05 1,10 c 1,85 1,95 d 4,17 4,21 e 4,39 4,44 f 55 2 g 1,63 1,83 h 0,00 0,15 i 2,10 j 0,60 0,72 k 1,80 1,90 l 2,10 2,30 m 45 2 Angle p b r 0,15 0,05 45 Chamfer aDimensions are chosen to meet mechanical performance requirem

39、ents, when mating with 0,68 mm0,71 mm pin. bThe diameter is chosen upon the assumption that the PTFE dielectric has a dielectric constant of 2,02 to give an impedance of 50 . 3.2 Gauges Gauge pin for socket-centre contact 3.2.1The gauge pin for socket-centre contact is shown in Figure 3 and its dime

40、nsions are shown in Table 3. IEC (1) (2) BS EN 61169-48:2015IEC 61169-48:2014 IEC 2014 9 Figure 3 Gauge pin for socket-centre contact Table 3 Dimensions of gauge pin for socket-centre contact Ref. Gauge A Maximum material for sizing purposes Gauge B Minimum material for measurement of retention forc

41、e Mass of gauge: 28 g + 2 g mm mm Min. Max. Min. Max. a 0,710 0,715 0,675 0,680 b 0,95 1,20 1,30 1,60 Material: steel, polished. Surface roughness: Ra = 0,4 m maximum on the cylindrical surface of length b. Test procedure 3.2.2The gauge A shall be inserted into the socket-centre contact three times

42、with a minimum depth of 0,95 mm. This is a sizing operation and should only be carried out when the socket-centre contact is removed from the connector. After this, the gauge B shall be inserted into socket-centre contact. The contact shall retain the mass of the gauge in a vertical downward positio

43、n. IEC BS EN 61169-48:2015 10 IEC 61169-48:2014 IEC 2014 Gauge for outer contact of connector with pin-centre contact 3.2.3Gauge A for sizing test 3.2.3.1The gauge A for sizing test is shown in Figure 4 and its dimensions are shown in Table 4. Figure 4 Gauge A for sizing test Table 4 Gauge A for siz

44、ing test Ref. Gauge A Maximum material for sizing purposes mm Min. Min. a 4,15 4,17 c 1,40 1,50 d 2,50 2,70 f 55 2 Material: steel, polished. Surface roughness: Ra=0,4 m maximum on the cylindrical surface of a and taper surface angle f . Test procedure 3.2.3.2The gauge A shall be inserted into the o

45、uter contact three times. This is a sizing operation. IEC BS EN 61169-48:2015IEC 61169-48:2014 IEC 2014 11 Gauge B for retention test for pin connectors Full detent 3.2.3.33.2.3.3.1 Dimensions for gauge B Gauge B for retention test for pin connectors full detent is shown in Figure 5 and its dimensio

46、ns are shown in Table 5. Figure 5 Gauge B for retention test for pin connectors Full detent Table 5 Gauge B for retention test for pin connectors Full detent Ref. Gauge B Minimum material for measurement of retention force Mass of gauge: 2 000 g + 100 g mm Min. Max. a 4,18 4,21 b 4,39 4,44 c 1,80 1,

47、90 d 2,50 2,70 e 45 1 f 55 2 g 0,60 0,72 Material: steel, polished. Surface roughness: Ra = 0,4 m maximum on the cylindrical surface of length a,b and taper surface angle e,f . 3.2.3.3.2 Test procedure The gauge B shall be inserted into outer contact. The engagement force shall not exceed 63 N, the

48、contact shall retain the mass of the gauge in a vertical downward position. IEC BS EN 61169-48:2015 12 IEC 61169-48:2014 IEC 2014 Gauge C for retention test for pin connectors Smooth bore 3.2.3.43.2.3.4.1 Dimension of the gauge Gauge C for retention test for pin connectors smooth bore is shown in Fi

49、gure 6 and its dimensions are shown in Table 6. Figure 6 Gauge C for retention test for pin connectors Smooth bore Table 6 Gauge C for retention test for pin connectors Smooth bore Ref. Gauge C Minimum material for measurement of retention force Mass of gauge: 200 g + 10 g mm Min. Max. a 4,15 4,17 c 1,40 1,50 d 2,50 2,70 f 55 2 Materia