EN 61215-1-3-2017 en Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3 Special requirements for testing of thin-film amorphous silicon based.pdf

1、Terrestrial photovoltaic (PV) modules Design qualification and type approvalPart 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV) modulesBS EN 61215-1-3:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD

2、NORME EUROPENNE EUROPISCHE NORM EN 61215-1-3 May 2017 ICS 27.160 Supersedes EN 61646:2008 English Version Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV) modules (IEC 61

3、215-1-3:2016) Modules photovoltaques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 1-3: Exigences particulires dessai des modules photovoltaques (PV) au silicium amorphe couches minces (IEC 61215-1-3:2016) Terrestrische kristalline Silizium-Photovoltaik-

4、(PV)-Module - Bauarteignung und Bauartzulassung - Teil 1-3: Besondere Anforderungen fr Prfungen von Photovoltaik-(PV)-Modulen aus amorphem Silizium (IEC 61215-1-3:2016) This European Standard was approved by CENELEC on 2017-01-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Reg

5、ulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC

6、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official ve

7、rsions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

8、the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENE

9、LEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61215-1-3:2017 E National forewordThis British Standard is the UK implementation of EN 61215-1-3:2017. It is identical to

10、IEC 61215-1-3:2016. Together with BS EN 61215-1-2:2017 and BS EN 61215-1-4:2017, it supersedes BS EN 61646:2008 , which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GEL/82, Photovoltaic Energy Systems.A list of organizations represented on this committee

11、can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 87368 3ICS 27.160Compli

12、ance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61215-1-3:2017EUR

13、OPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61215-1-3 May 2017 ICS 27.160 Supersedes EN 61646:2008 English Version Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic (PV)

14、modules (IEC 61215-1-3:2016) Modules photovoltaques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 1-3: Exigences particulires dessai des modules photovoltaques (PV) au silicium amorphe couches minces (IEC 61215-1-3:2016) Terrestrische kristalline Siliziu

15、m-Photovoltaik-(PV)-Module - Bauarteignung und Bauartzulassung - Teil 1-3: Besondere Anforderungen fr Prfungen von Photovoltaik-(PV)-Modulen aus amorphem Silizium (IEC 61215-1-3:2016) This European Standard was approved by CENELEC on 2017-01-11. CENELEC members are bound to comply with the CEN/CENEL

16、EC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or

17、 to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

18、the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe

19、mbourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische N

20、ormung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61215-1-3:2017 E BS EN 61215-1-3:2017EN 61215-1-3:2017 2 European foreword The text of document 82/1183/FDI

21、S, future edition 1 of IEC 61215-1-3, prepared by IEC/TC 82 “Solar photovoltaic energy systems“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61215-1-3:2017. The following dates are fixed: latest date by which the document has to be implemented at national level by pub

22、lication of an identical national standard or by endorsement (dop) 2017-11-05 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-05-05 This document supersedes EN 61646:2008. Attention is drawn to the possibility that some of the elements of thi

23、s document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61215-1-3:2016 was approved by CENELEC as a European Standard without any modification. BS EN

24、61215-1-3:2017EN 61215-1-3:2017 2 European foreword The text of document 82/1183/FDIS, future edition 1 of IEC 61215-1-3, prepared by IEC/TC 82 “Solar photovoltaic energy systems“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61215-1-3:2017. The following dates are fix

25、ed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-11-05 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-05-05 This document supersedes E

26、N 61646:2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61215-1-3:

27、2016 was approved by CENELEC as a European Standard without any modification. EN 61215-1-3:2017 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications Annexes ZA of EN 61215-1:2016 and EN 61215-2:2017 are applicable. BS EN 61215-1-3:2

28、017This page deliberately left blank 2 IEC 61215-1-3:2016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope and object . 5 2 Normative references 5 3 Terms and definitions 5 4 Test samples . 5 5 Marking and documentation . 5 6 Testing 5 7 Pass criteria 6 8 Major visual defects . 6 9 Report . 6 10 Modifications

29、 . 6 11 Test flow and procedures 6 11.1 Visual inspection (MQT 01) . 6 11.2 Maximum power determination (MQT 02) 6 11.3 Insulation test (MQT 03) . 6 11.4 Measurement of temperature coefficients (MQT 04) 6 11.5 Measurement of nominal module operating temperature (NMOT) (MQT 05) 6 11.6 Performance at

30、STC (MQT 06.1) and NMOT (MQT 06.2) 6 11.7 Performance at low irradiance (MQT 07) . 6 11.8 Outdoor exposure test (MQT 08) . 7 11.9 Hot-spot endurance test (MQT 09) 7 11.9.1 Purpose . 7 11.9.2 Hot-spot effect . 7 11.9.3 Classification of cell interconnection 7 11.9.4 Apparatus 7 11.9.5 Procedure 7 11.

31、9.6 Final measurements 7 11.9.7 Requirements 7 11.10 UV preconditioning test (MQT 10) . 7 11.11 Thermal cycling test (MQT 11) 7 11.12 Humidity-freeze test (MQT 12) 7 11.13 Damp heat test (MQT 13) 7 11.14 Robustness of terminations test (MQT 14) 8 11.15 Wet leakage current test (MQT 15) . 8 11.16 Sta

32、tic mechanical load test (MQT 16) 8 11.17 Hail test (MQT 17) 8 11.18 Bypass diode testing (MQT 18) . 8 11.19 Stabilization (MQT 19) 8 11.19.2 Criterion definition for stabilization . 8 11.19.3 Light induced stabilization procedure . 8 11.19.4 Other stabilization procedures . 8 11.19.5 Initial stabil

33、ization (MQT 19.1) . 9 11.19.6 Final stabilization (MQT 19.2) 9 2 IEC 61215-1-3:2016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope and object . 5 2 Normative references 5 3 Terms and definitions 5 4 Test samples . 5 5 Marking and documentation . 5 6 Testing 5 7 Pass criteria 6 8 Major visual defects . 6 9

34、Report . 6 10 Modifications . 6 11 Test flow and procedures 6 11.1 Visual inspection (MQT 01) . 6 11.2 Maximum power determination (MQT 02) 6 11.3 Insulation test (MQT 03) . 6 11.4 Measurement of temperature coefficients (MQT 04) 6 11.5 Measurement of nominal module operating temperature (NMOT) (MQT

35、 05) 6 11.6 Performance at STC (MQT 06.1) and NMOT (MQT 06.2) 6 11.7 Performance at low irradiance (MQT 07) . 6 11.8 Outdoor exposure test (MQT 08) . 7 11.9 Hot-spot endurance test (MQT 09) 7 11.9.1 Purpose . 7 11.9.2 Hot-spot effect . 7 11.9.3 Classification of cell interconnection 7 11.9.4 Apparat

36、us 7 11.9.5 Procedure 7 11.9.6 Final measurements 7 11.9.7 Requirements 7 11.10 UV preconditioning test (MQT 10) . 7 11.11 Thermal cycling test (MQT 11) 7 11.12 Humidity-freeze test (MQT 12) 7 11.13 Damp heat test (MQT 13) 7 11.14 Robustness of terminations test (MQT 14) 8 11.15 Wet leakage current

37、test (MQT 15) . 8 11.16 Static mechanical load test (MQT 16) 8 11.17 Hail test (MQT 17) 8 11.18 Bypass diode testing (MQT 18) . 8 11.19 Stabilization (MQT 19) 8 11.19.2 Criterion definition for stabilization . 8 11.19.3 Light induced stabilization procedure . 8 11.19.4 Other stabilization procedures

38、 . 8 11.19.5 Initial stabilization (MQT 19.1) . 9 11.19.6 Final stabilization (MQT 19.2) 9 BS EN 61215-1-3:2017IEC 61215-1-3:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ TERRESTRIAL PHOTOVOLTAIC (PV) MODULES DESIGN QUALIFICATION AND TYPE APPROVAL Part 1-3: Special requirements for tes

39、ting of thin-film amorphous silicon based photovoltaic (PV) modules FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote internati

40、onal co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter re

41、ferred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate

42、in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an intern

43、ational consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasona

44、ble efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC P

45、ublications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformi

46、ty. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication

47、. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for

48、 costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct ap

49、plication of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61215-1-3 has been prepared by IEC technical committee 82: Solar photovoltaic energy systems This edition cancels and replaces the second edition of IEC 61646, issued in 2008, and constitutes a technical revision. This edition constitutes a tec