EN 61249-2-30-2013 en Materials for printed boards and other interconnecting structures - Part 2-30 Reinforced base materials clad and unclad - Non-halogenated epoxide modified cya.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationMaterials for printed boards and other interconnecting structuresPart 2-30: Reinforced base materials clad and unclad Non-halogenated epoxide modified cyanate ester woven glass l

2、aminate of defined flammability (vertical burning test), copper-cladBS EN 61249-2-30:2013National forewordThis British Standard is the UK implementation of EN 61249-2-30:2013. It is identical to IEC 61249-2-30:2012.The UK participation in its preparation was entrusted to Technical Committee EPL/501,

3、 Electronic assembly technology 1 065 mm 1 155 mm; 1 065 mm 1 280 mm; 1 000 mm 1 000 mm; 1 000 mm 1 200 mm. 6.8.2 Tolerances for sheet sizes The size of sheet delivered by the supplier shall not deviate by more than 200+mm from the ordered size. 6.9 Cut panels 6.9.1 Cut panel sizes Cut panel sizes s

4、hall be, when delivered, in accordance with the purchasers specification. 6.9.2 Size tolerances for cut panels For panels cut to size according to the purchasers specification, the following tolerances for length and width shall apply as shown in Table 7. Tolerances indicated as normal shall be in e

5、ffect unless otherwise specified in the purchasing specification. BS EN 61249-2-30:2013 12 61249-2-30 IEC:2012 Table 7 Size tolerance for cut panels Panel size mm Tolerances mm Normal Close 300 2,0 0,5 300 600 2,0 0,8 600 2,0 1,6 NOTE The specified tolerances include all deviations caused by cutting

6、 the panels. 6.9.3 Rectangularity of cut panels For panels cut to size according to the purchasers specification, the following requirements for rectangularity shall apply, as shown in Table 8. Tolerance indicated as normal shall be in effect unless otherwise specified in the purchasing specificatio

7、n. Table 8 Rectangularity of cut panels Property Test method IEC 61189-2 Requirement mm/m Normal Close Rectangularity of cut panels 2M23 3 2 7 Non-electrical properties of the base material after complete removal of the copper foil 7.1 Appearance of the dielectric base material The etched specimens

8、shall be inspected to verify that no surface or subsurface imperfections of the dielectric material exceed those shown below. The specimens shall be inspected using an optical aid apparatus which provides a minimum magnification of 4X. Referee inspection shall be conducted at 10X magnification. Ligh

9、ting conditions of inspection shall be appropriate to the material under inspection or as agreed upon between user and supplier. Surface and subsurface imperfections (such as weave texture, resin starvation, voids, foreign inclusions) shall be acceptable, provided that the imperfections meet the fol

10、lowing: the reinforcement fibres are not cut or exposed; the foreign inclusions are not conductive. Metallic inclusions are not acceptable; the imperfections do not propagate as a result of thermal stress; the foreign inclusions are translucent; opaque foreign fibres are less than 15 mm in length an

11、d average no more than one occurrence per 300 mm 300 mm area; opaque foreign inclusions other than fibres shall not exceed 0,50 mm. Opaque foreign inclusions less than 0,15 mm shall not be counted. Opaque foreign inclusions between 0,50 mm and 0,15 mm shall average no more than two spots per 300 mm

12、300 mm area; voids (sealed voids or surface voids) have a longest dimension less than 0,075 mm and there should not be more than three voids in a 3,5 mm diameter circle. BS EN 61249-2-30:201361249-2-30 IEC:2012 13 7.2 Flexural strength When the laminate is tested in accordance with IEC 61189-2, meth

13、od 2M20, the flexural strength shall be as shown in Table 9. Table 9 Flexural strength Property Test method IEC 61189-2 Requirement Flexural strength: Length direction Cross-direction (applicable to specimens 1,0 mm in nominal thickness) 2M20 300 N/mm2200 N/mm2Flexural strength: Elevated temperature

14、(150 C) Length direction (applicable to specimens 1,0 mm in nominal thickness) 200 N/mm27.3 Flammability When the laminate is tested in accordance with method 2C08 (thickness 0,03mm 0,3 mm) or method 2C06 (thickness 0,3 1,6 mm) of IEC 61189-2, the flammability shall be as shown in Table 10. Flammabi

15、lity ratings other than those listed in Table 10 may be used, as agreed upon between user and supplier. The performance labelled V-0 shall be in effect, unless otherwise noted on the purchase order. Table 10 Flammability Property Test method IEC 61189-2 Requirements Designation V-0 V-1 Flammability:

16、 Flaming combustion time after each application of the flame for each test specimen Total flaming combustion time for the 10 flame applications for each set of five specimens Glowing combustion time after the second removal of the test flame Flaming or glowing combustion up to the holding clamp Drip

17、ping flaming particles that ignite the tissue paper 2C06 10 s 50 s 30 s None None 30 s 250 s 60 s None None 7.4 Water absorption When the laminate is tested in accordance with IEC 61189-2, method 2N02, the maximum water absorption shall be as shown in Table 11. BS EN 61249-2-30:2013 14 61249-2-30 IE

18、C:2012 Table 11 Water absorption Property Test method IEC 61189-2 Thickness mm Requirements % Water absorption 2N02 0,03 0,20 0,20 0,30 0,30 0,40 0,40 0,50 0,50 0,60 0,60 0,80 0,80 1,00 1,00 1,30 1,20 1,60 3,00 1,60 1,20 1,10 1,00 0,90 0,70 0,60 0,50 7.5 Measling When the laminate is tested in accor

19、dance with IEC 61189-2, method 2N01, the presence of measles allowed shall be as shown in Table 12. Table 12 Measling Property Test method IEC 61189-2 Requirements Measling 2N01 No measling on three specimens. If one out of three specimens fails, the test has to be repeated. No measling on three spe

20、cimens of the second test is permitted. No blistering nor delamination on any of the three specimens is permitted. 7.6 Glass transition temperature and cure factor The requirements for glass transition temperature and cure factor are found in Table 13. Table 13 Glass transition temperature and cure

21、factor Property Test method IEC 61189-2 Requirements Glass transition temperature 2M11 160 C Cure factor 2M03 Not specified 8 Quality assurance 8.1 Quality system The supplier shall operate a quality system, ISO 9000 or similar, to support quality conformance inspection. The supplier shall operate a

22、 management system for environmental control, ISO 14001 or similar, to support environmental considerations. BS EN 61249-2-30:201361249-2-30 IEC:2012 15 8.2 Responsibility for inspection The supplier is responsible for all inspections of the manufactured material. The purchaser or an appointed third

23、 party may audit this inspection. 8.3 Qualification inspection Laminates furnished under this specification shall be qualified. Qualification testing shall be performed to demonstrate the manufacturers ability to meet the requirements of this standard. Qualification testing shall be conducted at a l

24、aboratory compliant with IEC laboratory requirements. A list of the normal qualification tests can be found in Annex C. The manufacturer shall retain a data file which supports the claim that the materials meet this specification and shall be readily available for review upon request. 8.4 Quality co

25、nformance inspection The supplier shall operate a quality plan to ensure product conformance to this standard. Such a quality plan, when appropriate, should utilize statistical methods rather than lot-by-lot inspection. It is the responsibility of the supplier, based on the quality plan, to determin

26、e the frequency of test to ensure conforming products. In the absence of a quality plan or supporting data, the testing regime shall be as outlined in Annex C. A combination of the following techniques may be used to show compliance with the requirements which can be used to reduce the frequency of

27、testing. The data supporting the reduction of testing frequency shall be available for review upon request. In process parameter control In process inspection Periodic final inspection Final lot inspection 8.5 Certificate of conformance The supplier shall, on request from the purchaser, issue a cert

28、ificate of conformance to this standard in electronic or paper format. 8.6 Safety data sheet A safety data sheet in accordance with ISO 11014 shall be available for products manufactured and delivered in compliance with this standard. 8.7 Packaging and marking Unless otherwise specified in the purch

29、ase order, laminate sheets shall be marked with the manufacturers designation, nominal thickness, copper cladding, and lot number. Marking shall remain legible during normal handling but be readily removable prior to use of the material. Cut panels shall be identified by marking on the package only.

30、 Sheets or cut panels of laminates comprised of asymmetric copper cladding shall be marked on the side of heaviest copper weight. Sheets and cut panels shall be packaged in a manner which will provide adequate protection against corrosion, deterioration and physical damage during shipment and storag

31、e. Packages of sheets and cut panels shall be marked in a manner to clearly identify the contents. BS EN 61249-2-30:2013 16 61249-2-30 IEC:2012 9 Ordering information Order shall include the following details: a) reference to this standard; b) type of material (see Clause 1 and 7.3); c) size, thickn

32、ess and copper cladding; d) class of indentations (see 6.1.2); e) class of raised areas (see 6.1.5); f) class of thickness tolerance (see 6.3); g) class of dimensional stability (see 6.7); h) class of panel size tolerance (see 6.9.2); i) class of flammability (see 7.3); and j) request for certificat

33、ion, if applicable (see 8.5). BS EN 61249-2-30:201361249-2-30 IEC:2012 17 Annex A (informative) Engineering information A.1 General Information in this annex does not detail material property requirements. The information is intended as a general guideline for design and engineering purposes only. I

34、f specific information is required by the user, the supplier of the actual material to this standard shall be contacted for that specific engineering information. Users of this standard are encouraged to supply additional engineering information to be included in future revisions to this annex. Mate

35、rials according to this standard are expected to show the following typical data for the properties listed. A.2 Chemical properties Resistance against chemicals A.3 Electrical properties Comparative tracking index (175 250) V A.4 Flammability properties Needle flame test Oxygen index (50 80) % A.5 M

36、echanical properties Compressive strength (flatwise) Compressive strength (edgewise) Hardness at room temperature Modulus of elasticity, flexural (warp) 1,9 104N/mm2 Modulus of elasticity, flexural (weft) 1,5 104N/mm2 Modulus of elasticity, tensile (warp) 1,7 104N/mm2 Modulus of elasticity, tensile

37、(weft) 1,4 104N/mm2 Poissons ratio 0,17 0,21 Shear strength BS EN 61249-2-30:2013 18 61249-2-30 IEC:2012 Youngs modulus (25 30) GPa A.6 Physical properties Density (1,80 2,20) g/cm3A.7 Thermal properties Coefficient of thermal expansion (Tg) 200 ppm/C Specific heat capacity Thermal conductivity 0,7

38、0,9 W/(mC) UL temperature index (mechanical) C (now approving) UL temperature index (electrical) C (now approving) Maximum operating temperature (MOT) C (now approving) BS EN 61249-2-30:201361249-2-30 IEC:2012 19 Annex B (informative) Common laminate constructions Information in this annex does not

39、detail requirements for constructions for specific thicknesses, see Table B.1. The information is intended as a general guideline for design and engineering purposes only. Other constructions with superior performance properties may be available commercially for any given thickness. If specific cons

40、truction information is required by the user, the supplier of the actual material to this standard shall be contacted for that specific construction information. Table B.1 Thickness Nominal thickness mm Common construction 0,03 1 027 0,04 2 1 015 0,05 2 1 027 0,06 2 1 027 0,10 2 116 0,10 2 1 078 0,1

41、5 1 504 0,15 3 1 078 0,20 2 2 116 0,20 4 1 078 0,25 2 116/1 078/2 116 0,30 3 2 116 0,40 4 2 116 0,45 2 2 116/1 078/2 2 116 0,5 5 2 116 0,6 6 2 116 0,7 7 2 116 0,8 8 2 116 0,9 9 2 116 1,0 10 2 116 1,1 11 2 116 1,2 12 2 116 1,3 13 2 116 1,4 14 2 116 1,5 15 2 116 1,6 16 2 116 NOTE Prepreg made from a s

42、pecific style of glass used in different constructions may have different resin contents. BS EN 61249-2-30:2013 20 61249-2-30 IEC:2012 Annex C (informative) Guideline for qualification and conformance inspection Information in this annex does not represent requirements for qualification and conforma

43、nce testing. The Manufacturers Quality System shall define the actual qualification and conformance testing for materials supplied to this standard. Test data and test summaries shall be available to support the qualification and conformance testing schemes utilized. In the absence of relevant infor

44、mation in a Manufacturers Quality System, this annex shall be used, see Table C.1. Table C.1 Qualification and conformance testing Property Test method IEC 61189-2 Qualification testing Conformance testing Conformance frequency Peel strength after thermal shock 2M14 Yes Yes Lot Peel strength at 125

45、C 2M15 Yes Yes Quarterly Peel strength after solvent vapour 2M06 Yes Yes Quarterly Peel strength after simulated plating 2M16 Yes No Pull off strength 2M05 Yes No Dimensional stability 2X02 Yes Yes Monthly Flexural strength 2M20 Yes Yes Annually Flammabilty 2C06 Yes Yes Monthly Thermal stress, unetc

46、hed 2C05 Yes Yes Lot Solderability 2MXX Yes No Glass transition temperature 2M10 Yes Yes Monthly Cure Factor 2M03 Yes No Relative permittivity at 1 MHz after damp heat and recovery 2E10 Yes Yes Monthly Dissipation factor at 1 MHz after damp heat and recovery 2E10 Yes Yes Monthly Surface resistance a

47、fter damp heat/recovery 2E03 Yes Yes Annually Volume resisitivity after damp heat/recovery 2E04 Yes Yes Annually Arc resistance 2E14 Dielectric breakdown 2E15 Electric strength 2E11 Water absorption 2N02 Yes Yes Quarterly Bow and twist 2M01 Yes Yes Lot Surface waviness 2M12 Yes No Appearance of the

48、dielectric base material See 7.1 Yes Yes Lot BS EN 61249-2-30:201361249-2-30 IEC:2012 21 Bibliography IEC 60194:2006, Printed board design, manufacture and assembly Terms and definitions ISO 9000:2005, Quality management systems Fundamentals and vocabulary ISO 14001:2004, Environmental management systems Requirements with guidance for use _ BS EN 61249-2-30:2013This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, informatio