1、BRITISH STANDARD BS EN61300-2-46:2006Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-46: Tests Damp heat cyclicICS 33.180.20nullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnullnullnull
2、 nullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnullnullIncorporatingcorrigendumOctober 2012National forewordThis British Standard is the UK implementation of EN 61300-2-46:2006. It is identical to IEC 61300-2-46:2006, incorpo
3、rating corrigendum October 2012.The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components.A list of organizations represented on this subcommittee can be obtained on request
4、to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 61300-2-46:2006This British Standard waspublished under t
5、he authorityof the Standards Policy andStrategy Committeeon 29 September 2006 The British StandardsInstitution 2013. Publishedby BSI Standards Limited2013Amendments/corrigenda issued since publicationDate Comments Implementation of IEC corrigendum October 2012: Clause 3 modifiedISBN 978 0 580 81181
6、430 June 2013EUROPEAN STANDARD EN 61300-2-46NORME EUROPENNE EUROPISCHE NORM August 2006 CENELEC European Committee for Electrotechnical StandardizationComit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat:rue de Stassart35, B - 1050 Brus
7、sels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELECmembers.Ref. No. EN 61300-2-46:2006 EICS 33.180.20 English version Fibre opticinterconnecting devices and passive components - Basic test and measurement procedures Part 2-46: Tests - Damp heat
8、cyclic (IEC 61300-2-46:2006)Dispositifs dinterconnexion et composants passifs fibres optiques -Mthodes fondamentales dessais et de mesures Partie 2-46: Essais - Chaleur humide, essai cyclique (CEI 61300-2-46:2006)Lichtwellenleiter -Verbindungselemente und passive Bauteile -Grundlegende Prf- und Mess
9、verfahrenTeil 2-46: Prfungen -Feuchte Wrme (zyklisch)(IEC 61300-2-46:2006)This European Standard was approved by CENELEC on 2006-08-01. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nation
10、al standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in a
11、ny otherlanguage made by translation under the responsibility of a CENELEC member into its own language and notifiedto the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, D
12、enmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 86B/2304/FDIS, future edi
13、tion 1 of IEC 61300-2-46, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to theIEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-2-46 on 2006-08-01. The following dates were fixed: latest date by which the EN
14、has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-05-01 latestdate by which the national standards conflictingwith the EN have to be withdrawn (dow) 2009-08-01 Annex ZA has been added by CENELEC. _ Endorsement noticeThe textofthe In
15、ternational Standard IEC 61300-2-46:2006 was approved by CENELEC asa European Standard without any modification. _ 2 BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)CONTENTS1 Scope.42Normative reference.43General description 44Apparatus. .55Procedure. .56Severity67Details tobe specified8 3 Annex ZA (nor
16、mative) Normative references to international publications with their corresponding European publications .10BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TESTAND MEASUREMENT PROCEDURES Part 2-46: Tests Damp heat, cyclic 1 Scope The purp
17、ose of thispart of IEC 61300 is to describe a test to determine the sui tability of a fibre opticdevice to withstand the environmental condition of high humidity and change oftemperature which mayoccur in actual use, storage and/or transport. The test is primarilyintended to determine the suitabilit
18、y of fibre optic components underconditions of highhumidity -combined with cyclic temperature changes and, in general, producing condensationon the surface of the specimen.Absorptionof moi sture may resultinswelling that would destroy functional utility, cause loss ofphysical strength, and cause cha
19、nges in otherimportant mechanical properties. Degradation of optical propertiesmay also occur. Althoughnot necessarily intended as a simulated tropicaltest, th is test can, nevertheless, be useful indetermining moisture absorption of insulating or covering materials.2 Normative reference The followi
20、ng referenced documents are indispensable for the application of this document.For dated references, only the edition cited applies. For undated references, thelatesteditionof the referenced document (including any amendments)applies.IEC 60068-2-30, Environmental testing - Part 2-30: Tests Test Db:
21、Damp heat,cyclic (12 h +12 h cycle)IEC 61300-3-3, Fibre optic interconnecting devices and passive components Basic test and measurementprocedures Part 3-3: Examinations and measurements Active monitoring ofchanges in attenuation and return loss 3 Generaldescription This procedure is conducted inacco
22、rdance with IEC 60068-2-30,test Db, variant .Thespecimen is placed in achamber and subjected to a damp-heat environment which ismaintained at giventemperatures and relative humidityfor a specified duration, as specifiedin the relevant specification. 4 2BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)4 A
23、pparatus 4.1 ChamberThe apparatus consists of an environmental chamber in accordance with IEC 60068-2-30, testDb. The chamber shall be capable of housing the specimenand ofallowing access formeasurement during conditioning. It shall also be capable of maintaining the specif ied temperatures and humi
24、ditywithin the specified tolerances. Forced air circulation maybe used to maintainhomogeneous conditions. The chamberand accessories shall be constructedandarrangedin such a manner as to avoid condensation on the specimens. Water: usedistilled, demineralized or deionized water to obtain the specifie
25、dhumidity. No rustor corrosion contaminant sshall be imposed on the specimen by the test facility.4.2 Other apparatus Additional apparatusmay be necessary to performthe examinations and measurementsspecified by therelevant specification. 5 Procedure 5.1Preparation of specimens Prepare the specimen a
26、ccording to the manufacturers instructions oras specified in therelevant specification. The specimen shallbe terminated with a sufficientlength of fibre cable to facilitate connection with the optical source and detector.Maintain the specimen under standard atmospheric conditions (room temperature c
27、ondition)for 2h minimum.Clean the mechanical and optical alignment parts of the specimen according to the manufacturers instructions. 5.2 Initial examinations and measurementsIf specified, perform initial examinations and measurements as required by the relevantspecification. 5.3 Conditioning 5.3.1
28、Stabilize the chamber and the specimen to standard atmospheric conditions. Place thespecimen in the chamber in its normal operating position, including hook-ups to peripheral equipment (when required).5.3.2 Adjust the chamber temperature and humidityto the specified severity. The rate ofchange of te
29、mperature shall not exceed 1 C/min, averaged over a maximum period of 5 min.In any case the rising temperatureshouldstay within the limits indicated in Figure 1.5.3.3 At the completion of the test, allowthe specimen to remain in the chamberwhile thetemperatureis gradually reduced to standard atmosph
30、eric conditions. The rate of change oftemperature shall not exceed 1 C/min,averaged overa maximum period of 5 min. In anycase the decreasing temperature should staywithin thelimits indicated in Figure 1. 5 BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)5.3.4 Where optical measurements are re quired dur
31、ing the test, measurements shall be made at a maximum interval of1 h. Do not remove the specimen(s) from the chamber whentaking thesemeasurements. Measurements shall be made in accor dance with IEC 61300-3-3. 5.4 Recovery Allow the specimen to remain under standard atmospheric conditions for a perio
32、d of2 h.5.5 Final examinations and measurementsPerformfinal examinations and measurements asrequired by the relevant specification.6 SeverityDetails:test cycle:(see Figure 1) high temperature:+55 C 2 Clow temperature: +25 C 2 C humidity: 90 % duration of each cycle: 24 h number of cycles: 6 6 BS EN
33、61300-2-46:2006 EN 61300-2-46:2006 (E)80 %90 % 95 %96 %95 %15 min15 min 15 min100 90 80 70 60 +25 h3 h12 h 6 h3 h24 hTimeStart of the temperature fallEnd of the temperature rise Relativehumidity % Ambiant temperature C+27C+23 CUpper temperature +2 Upper temperature 2 +55 IEC 1212/06 Figure 1 Test Db
34、 Test cycle 7 BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)7 Details to be specified The following details,asapplicable, shall be specified in the relevant specification: specimen optically functioning ornon-functioning; specimen mated or unmated (for connectors);initial examinations and measurements
35、 and performance requirements; examinations andmeasurements duringtest and performancerequirements;final examinations andmeasurements and performance requirements; deviations from test procedure; additional pass/fail criteria. 8 BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)BibliographyIEC 61300-3-1,
36、Fibre optic interconnect ing devices and passive components Bas ic testand measurementprocedures Part 3-1: Examinationsand measurements - Visual examination _ NOTE Harmonized as EN 61300-3-1:2005 (not modified). 9 BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)Annex ZA(normative)Normative references to
37、 international publications with their corresponding European publicationsThe following referenced documents are indisp ensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenceddocument (including
38、any amendments) applies.NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HDapplies.Publication Year Title EN/HD YearIEC 60068-2-30 - 1) Environmental testingPart 2-30: Tests - Test Db: Damp heat, cyclic(12 h + 12 h cycle)EN 60068-2
39、-30 20052)IEC 61300-3-3 - 1) Fibre optic interconnecting devices and passive components - Basic test andmeasurement proceduresPart 3-3: Examinations and measurements -Active monitoring of changes in attenuation and returnlossEN 61300-3-3 20032)1) Undated reference.2) Valid edition at date of issue.
40、10 BS EN 61300-2-46:2006 EN 61300-2-46:2006 (E)blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated
41、by Royal Charter . British Standards and other standardizationproducts are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated
42、 by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British
43、 Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating
44、 service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the
45、 website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relev
46、ant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date w
47、ith standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via Br
48、itish Standards Online can be found at information about British Standards is available on the BSI website at the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be repro
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1