EN 61300-2-47-2016 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47 Tests - Thermal shocks.pdf

1、Fibre optic interconnecting devices and passive components Basic test and measurement proceduresPart 2-47: Tests Thermal shocksBS EN 61300-2-47:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN 6

2、1300-2-47:2016. It isidentical to IEC 61300-2-47:2016. It supersedes BS EN 61300-2-47:2010which is withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of

3、 organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited

4、 2016ISBN 978 0 580 86015 7ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate Text a

5、ffectedBRITISH STANDARDBS EN 61300-2-47:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61300-2-47 September 2016 ICS 33.180.20 Supersedes EN 61300-2-47:2010 English Version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47: Tests

6、 - Thermal shocks (IEC 61300-2-47:2016) Dispositifs dinterconnexion et composants passifs fibroniques - Procdures fondamentales dessais et de mesures - Partie 2-47: Essais - Chocs thermiques (IEC 61300-2-47:2016) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prf- und Me

7、ssverfahren - Teil 2-47: Prfungen - Temperaturschock (IEC 61300-2-47:2016) This European Standard was approved by CENELEC on 2016-06-23. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nati

8、onal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A

9、 version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulg

10、aria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer

11、land, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in an

12、y form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61300-2-47:2016 E BS EN 61300-2-47:2016EN 61300-2-47:2016 2 European foreword The text of document 86B/3879/CDV, future edition 4 of IEC 61300-2-47, prepared by SC 86B “Fibre optic interconnecting devices and passive compone

13、nts“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-47:2016. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (

14、dop) 2017-03-23 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-06-23 This document supersedes EN 61300-2-47:2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC a

15、nd/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61300-2-47:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note

16、has to be added for the standard indicated: IEC 61753-1 NOTE Harmonized as EN 61753-1. BS EN 61300-2-47:2016EN 61300-2-47:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are no

17、rmatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified

18、by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60068-2-14 - Environmental testing - Part 2-14: Tests

19、- Test N: Change of temperature EN 60068-2-14 - IEC 61300-3-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 - BS EN 61300-2-47:2016 2 IEC 61300-2-47:2016 IEC 2016 CONTEN

20、TS FOREWORD . 3 1 Scope 5 2 Normative references. 5 3 General description . 5 4 Apparatus 5 4.1 Testing chambers 5 4.2 Support for mounting the DUT . 6 5 Procedure . 6 5.1 General . 6 5.2 Preconditioning . 6 5.3 Initial examination and measurement . 6 5.4 Testing . 6 5.5 Recovery 7 5.6 Final examina

21、tion and measurement 7 6 Severity . 7 7 Details to be specified . 8 Annex A (informative) Minimum temperature value in Finland . 9 Bibliography . 10 Figure 1 Temperature change cycle 7 BS EN 61300-2-47:2016IEC 61300-2-47:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCO

22、NNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-47: Tests Thermal shocks FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees).

23、 The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Spe

24、cifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizatio

25、ns liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters

26、 express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National C

27、ommittees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Na

28、tional Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself do

29、es not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they h

30、ave the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature what

31、soever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced public

32、ations is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Stan

33、dard IEC 61300-2-47 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This fourth edition cancels and replaces the third edition published in 2010. This edition constitutes a technical revision. This editio

34、n includes the following significant technical change with respect to the previous edition: review of temperature limit in the test severity. BS EN 61300-2-47:2016 4 IEC 61300-2-47:2016 IEC 2016 The text of this standard is based on the following documents: CDV Report on voting 86B/3879/CDV 86B/3937

35、A/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The readers attention is drawn to the fact that Annex A lists an “in some-cou

36、ntry” clause on differing practices of a less permanent nature relating to the subject of this standard. A list of all parts in the IEC 61300 series, published under the general title Fibre optic interconnecting devices and passive components Basic test and measurement procedures, can be found on th

37、e IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, rep

38、laced by a revised edition, or amended. BS EN 61300-2-47:2016IEC 61300-2-47:2016 IEC 2016 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-47: Tests Thermal shocks 1 Scope This part of IEC 61300 details a procedure for determining the suitabil

39、ity of a fibre optic device to withstand the effects of thermal shock. In practice, this means a very short change over time between extreme temperatures. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its ap

40、plication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-14, Environmental testing Part 2-14: Tests Test N: Change of temperature IEC 61300-3-1, Fibre optic interconnecting d

41、evices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination 3 General description The procedure described in this standard is conducted in accordance with IEC 60068-2-14, test Na. The device under test (DUT) is first subjected to one

42、 extreme of temperature for a given period of time. It is then subjected to the other extreme of temperature for an equal period of time. Two test methods are considered: manual or automatic. Both methods are considered as equivalent. The reference method is the automatic one. 4 Apparatus 4.1 Testin

43、g chambers a) Two separate chambers or one rapid temperature change rate may be used. If two chambers are used, one for the low temperature and one for the high temperature, they are located such as to allow transfer of the DUT from one chamber to the other within the prescribed time. Either manual

44、or automatic transfer methods may be used. b) The chambers shall be capable of maintaining the atmosphere at the appropriate temperature for the test in any region where the DUT is placed. c) The absolute humidity of the atmosphere inside the chambers should not exceed 20 g/m3. At the temperature of

45、 60 C and standard air pressure, the relative humidity should be less than 16 %. d) The temperature of the walls of the hot and cold chambers shall not differ by more than 3 % and 8 % respectively from the specified ambient temperature of the test, expressed in Kelvin (tolerance of 3 % for high temp

46、erature, and 8 % for low temperature). BS EN 61300-2-47:2016 6 IEC 61300-2-47:2016 IEC 2016 e) The volume of the chambers and the air velocity shall be such that after insertion of the DUT, the temperature of the atmosphere shall be within the specified tolerance after a time of not more than 10 % o

47、f the exposure time. f) The air of the chamber shall be circulated so that the air velocity, measured close to the DUT, shall be not less than 2 m/s. 4.2 Support for mounting the DUT Unless otherwise specified in the relevant specification, the thermal conductivity of the supports for mounting the D

48、UT shall be low, such that for practical purposes the DUT is thermally isolated. When testing several DUTs simultaneously, they shall be so placed that free circulation should be provided between DUTs, and between DUTs and chamber surfaces. 5 Procedure 5.1 General Conduct the test according to the f

49、ollowing procedure. If the component construction includes optical leads, include 1,5 m of cable in the climatic chamber for each port monitored during the test. If optical measurements are requested during the test by the relevant specification, these measurements shall be performed at a maximum interval of 10 min during the extreme temperature periods. It is not the intention of the test to record the effects of mechanical movement of the optical cables during the mov