EN 61340-5-3-2015 en Electrostatics - Part 5-3 Protection of electronic devices from electrostatic phenomena - Properties and requirements classification for packaging intended for.pdf

1、BSI Standards PublicationElectrostatics Part 5-3: Protection of electronic devices from electrostatic phenomena Properties and requirements classification for packaging intended for electrostatic discharge sensitive devicesBS EN 61340-5-3:2015National forewordThis British Standard is the UK implemen

2、tation of EN 61340-5-3:2015. It isidentical to IEC 61340-5-3:2015. It supersedes BS EN 61340-5-3:2010 whichwill be withdrawn on 20 August 2018.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/101, Electrostatics.A list of organizations represented on this committee can

3、 be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 84109 5ICS 17.220.99; 29.020

4、Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61340-5-3:201

5、5EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61340-5-3 October 2015 ICS 17.220.99; 29.020 Supersedes EN 61340-5-3:2010 English Version Electrostatics - Part 5-3: Protection of electronic devices from electrostatic phenomena - Properties and requirements classification for packaging intended

6、 for electrostatic discharge sensitive devices (IEC 61340-5-3:2015) lectrostatique - Partie 5-3: Protection des dispositifs lectroniques contre les phnomnes lectrostatiques - Classification des proprits et des exigences relatives lemballage destin aux dispositifs sensibles aux dcharges lectrostatiqu

7、es (IEC 61340-5-3:2015) Elektrostatik - Teil 5-3: Schutz von elektronischen Bauelementen gegen elektrostatische Phnomene - Eigenschaften und Anforderungen fr die Klassifizierung von Verpackungen, welche fr Bauelemente verwendet werden, die gegen elektrostatische Entladungen empfindlich sind (IEC 613

8、40-5-3:2015) This European Standard was approved by CENELEC on 2015-08-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bib

9、liographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the r

10、esponsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, F

11、inland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for El

12、ectrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members

13、. Ref. No. EN 61340-5-3:2015 E BS EN 61340-5-3:2015EN 61340-5-3:2015 2 European foreword The text of document 101/428/CDV, future edition 2 of IEC 61340-5-3, prepared by IEC/TC 101 “Electrostatics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61340-5-3:2015. The follo

14、wing dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-05-20 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-08-20 This doc

15、ument supersedes EN 61340-5-3:2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International S

16、tandard IEC 61340-5-3:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61340-5-1 NOTE Harmonized as EN 61340-5-1. IEC 60749-26 NOTE Harmonized as EN 60749-26.

17、 BS EN 61340-5-3:2015EN 61340-5-3:2015 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dat

18、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-da

19、te information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60417 - Graphical symbols for use on equipment - - IEC 61340-2-3 - Electrostatics - Part 2-3: Methods of test for determining the resistance a

20、nd resistivity of solid planar materials used to avoid electrostatic charge accumulation EN 61340-2-3 - IEC 61340-4-8 - Electrostatics - Part 4-8: Standard test methods for specific applications - Electrostatic discharge shielding - Bags EN 61340-4-8 - IEC 61340-4-10 - Electrostatics - Part 4-10: St

21、andard test methods for specific applications - Two-point resistance measurement - - BS EN 61340-5-3:2015 2 IEC 61340-5-3:2015 IEC 2015 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms, definitions and abbreviations . 7 3.1 Terms and definitions 7 3.2 Abbreviations 9

22、 4 Tailoring 9 5 Packaging application requirement 9 5.1 General . 9 5.2 Inside an EPA . 9 5.3 Outside an EPA 9 6 Classification of ESD packaging material properties 10 6.1 General . 10 6.2 Material resistance properties . 10 6.2.1 General . 10 6.2.2 Resistance of conductive materials 10 6.2.3 Resis

23、tance of electrostatic field shielding materials . 10 6.2.4 Resistance of dissipative materials 11 6.2.5 Resistance of insulating materials 11 6.3 Material electrostatic shielding properties . 11 6.3.1 Electrostatic discharge shielding 11 6.3.2 Electrostatic field shielding 11 7 Technical requiremen

24、ts for ESD protective packaging . 11 7.1 Packaging and material properties 11 7.2 Packaging marking . 13 7.2.1 Classification symbol . 13 7.2.2 Packaging classification. 13 7.2.3 Traceability 14 Annex A (informative) ESD packaging material guidance . 15 A.1 Environment and device sensitivity . 15 A.

25、1.1 General . 15 A.1.2 Environment 15 A.1.3 Device sensitivity . 16 A.2 Equipotential bonding . 17 A.3 Dissipative material for intimate contact 17 A.4 Packaging from incoming material to the point of use 17 A.5 Periodic verification 18 A.6 Examples of measurement procedures for qualification and ve

26、rification of packaging . 19 Annex B (informative) Device damage . 20 B.1 Damage from ESD 20 B.2 Discharge to a device . 20 B.2.1 Human body model (HBM) 2 and isolated conductors 20 B.2.2 Retained charge 20 BS EN 61340-5-3:2015IEC 61340-5-3:2015 IEC 2015 3 B.3 Discharge from a device . 20 B.3.1 Char

27、ged device model (CDM) 20 B.3.2 Tribo-electrification 20 Bibliography 21 Figure 1 Example of packaging label (*Primary function code) . 13 Figure A.1 Examples of EPA configurations . 16 Figure A.2 Application of ESD protective packaging . 18 Table 1 Test methods for electrostatic protective packagin

28、g 12 Table 2 Test methods and requirements for electrostatic discharge shielding packaging . 12 Table 3 Primary function code/ESD classification symbol . 14 Table A.1 Packaging characteristics for environmental consideration . 15 Table A.2 Examples for qualification and verification of packaging . 1

29、9 BS EN 61340-5-3:2015 4 IEC 61340-5-3:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTROSTATICS Part 5-3: Protection of electronic devices from electrostatic phenomena Properties and requirements classification for packaging intended for electrostatic discharge sensitive devices FORE

30、WORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the ele

31、ctrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to te

32、chnical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Org

33、anization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technic

34、al committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publica

35、tions is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their nation

36、al and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment servi

37、ces and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, serva

38、nts or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publicatio

39、n, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility

40、that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61340-5-3 has been prepared by IEC technical committee 101: Electrostatics. This second edition cancels a

41、nd replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) removal of all references to ANSI/ESD STM11.13, replaced by normative reference IEC 61340-4-10; b

42、) additional notes added to Table 1; c) addition of a new Table 3 related to the “ESD classification symbol” and the “primary function code”. BS EN 61340-5-3:2015IEC 61340-5-3:2015 IEC 2015 5 The text of this standard is based on the following documents: CDV Report on voting 101/428/CDV 101/457/RVC

43、Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 61340 series, under the general title Electrostatics

44、, can be found on the IEC website The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfir

45、med, withdrawn, replaced by a revised edition, or amended. BS EN 61340-5-3:2015 6 IEC 61340-5-3:2015 IEC 2015 INTRODUCTION Packaging is necessary to protect electrostatic discharge sensitive devices (ESDS) from physical and environmental damage during manufacture, transportation and storage. Additio

46、nally, packaging for ESDS should also prevent damage from static electricity. BS EN 61340-5-3:2015IEC 61340-5-3:2015 IEC 2015 7 ELECTROSTATICS Part 5-3: Protection of electronic devices from electrostatic phenomena Properties and requirements classification for packaging intended for electrostatic d

47、ischarge sensitive devices 1 Scope This part of IEC 61340 defines the ESD protective packaging properties needed to protect electrostatic discharge sensitive devices (ESDS) through all phases of production, rework/maintenance, transport and storage. Test methods are referenced to evaluate packaging

48、and packaging materials for these product and material properties. Performance limits are provided. This standard does not address protection from electromagnetic interference (EMI), electromagnetic pulsing (EMP) or protection of volatile materials. 2 Normative references The following documents, in

49、 whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61340-2-3, Electrostatics Part 2-3: Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation IEC 61340-4-8, Electr