1、 STD-BSI BS EN bLSbb-3-ENGL 2000 m Lb24bb7 0b70q7 787 = BRITISH STANDARD Multimedia systems and equipment - Colour measurement and management - Part 3: Equipment using cathode ray tubes The European standard EN 619632 has the status of a British Stanard ICs 33.160.60 BS EN 61966-3:ZOoO IEC 619663:20
2、00 NO COPYING WITHOUT BSI PEBMISSION EXCEPT AS PEBMIITED BY COPYRIGHT LAW STDDBSI BS EN blSbb-3-ENGL 2000 M Lb24bb9 08bS048 815 direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 September 2000 Amd. No. BS EN 6
3、19663:2000 D - present to the responsible inte - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this commitee can be obtained on request to its SeCretaIy. Cross-references Attention is drawn to the fact that CEN and CENEL
4、EC standards normally include an annex which lists normative references to international publications with their corresponding European pubiications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Caaiogue u
5、nder the section entitied “international Standards Correspondence index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ail the necessary provisions of a contract. Users of British standards are responsible for their correct
6、 application. Compliance with a British Standard does not of itself confer immunity from legai obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 35 and a back cover. The BSI copyright notice displayed in this document indicahs w
7、hen the document was last issued. 0 BSI 09-2000 - ISBN O S8 36417 8 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61 966-3 April 2000 ICs 33.160.60 37.080 English version Multimedia systems and equipment - Colour measurement and management Part 3: Equipment using cathode ray tubes (IEC 61 966
8、-3:2000) Systmes et appareils multimdia Mesure et gestion de la couleur Partie 3: Equipement utilisant des tubes Multimediasysteme und -gerate - Farbmessungen und Farbmanagement Teil 3: Gerte mit Kathodenstrahirhren cathodiques (IEC 61 966-3:2008) (CE1 61 966-3:2000) This European Standard was appro
9、ved by CENELEC on 2000-04-01. CENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such natio
10、nal standards may be obtained on application to the Central Secretariat or to any CENELEC member, This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language
11、 and notified to the Central Secretariat has the same status as the officiai versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spai
12、n, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2000 CENELEC - All rights of exploita
13、tion in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61 966-3:20OO E STD-BSI BS EN bL9bb-3-ENGL 2000 Lb2qbb9 08b9050 473 Page 2 EN 61966-3:ZOOO Foreword The text of document 100/118/FDIS, future edition 1 of IEC 61 966-3, prepared by IEC TC 100, Audio, video and mult
14、imedia systems and equipment, was submitted to the IEC- CENELEC parallel vote and was approved by CENELEC as EN 61 966-3 on 2000-04-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorse
15、ment (dop) 2001 -01 -01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2003-04-0 1 Annexes designated “normative“ are part of the body of the standard. Annexes designated “informative“ are given for information only. In this standard, annexes A, B an
16、d ZA are normative and annexes C and D are informative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 61966-3:ZOOO was approved by CENELEC as a European Standard without any modification. STD-BSI BS EN bLSbb-3-ENGL 2000 Lb29bbS OBb905L 30T = Page 3
17、 EN 61966-3:2000 CONTENTS Page Clause 1 2 3 4 5 6 7 8 9 Scope 5 Normative references . 5 Terms and definitions 6 Letters and symbols . 6 Conditions . 7 5.1 Environmental conditions 7 5.2 Conditions of measurements . 7 5.3 Input digital data . 9 Measurement equipment 10 6.1 Spectroradiometer 10 6.2 C
18、olorimeter . 10 Spectral characteristics and intensity of the primaries and white stimuli 11 7.1 Characteristics to be measured . 11 7.2 Measurement conditions . 11 7.3 Method of measurement . 11 7.4 Presentation of results 12 Basic colorimetric characteristics . 12 8.1 Characteristics to be measure
19、d . 12 8.2 Method of measurement . 13 8.3 Presentation of results 13 Tone characteristics 14 9.1 Characteristics to be measured . 14 9.2 Measurement conditions . 15 9.3 Method of measurement . 15 9.4 Presentation of results 15 10 Inter-channel dependency 18 10.1 Characteristics to be measured . 18 1
20、0.2 Measurement conditions . 18 10.3 Method of measurement . 18 10.4 Presentation of results 20 11 Spatial non-uniformity 21 11 .I Characteristics to be measured . 21 11.2 Measurement conditions . 21 11.3 Method of measurement . 22 11.4 Presentation of results 23 12 Temporal stability 24 12.1 Short-
21、term stability . 24 12.1.1 Characteristics to be measured . 24 12.1.2 Measurement conditions . 24 12.1.3 Method of measurement 24 12.1.4 Presentation of results 24 8 BSI 09-2000 . Page 4 EN 61966-3:2000 12.2Mid-term stability 25 12.2.1 Characteristics to be measured . 25 12.2.2 Measurement condition
22、s . 25 12.2.3 Method of measurement 26 12.2.4 Presentation of results 26 13 Surface reflection 27 13.1 Characteristics to be measured . 27 13.3 Method of measurement . 28 13.4 Presentation of the result 28 14 Internal flare 29 14.1 Characteristics to be measured . 29 14.2 Measurement conditions . 29
23、 14.3 Method of measurement . 29 14.4 Presentation of results 29 13.2 Measurement conditions . 27 Annex A (normative) Required colorimetric instruments . 30 Annex B (normative) Alternative method of measurement of surface reflection 31 Annex C (informative) Evaluation of effect of external light sou
24、rce 32 Annex D (informative) Evaluation of internal and external flare . 33 Bibliograph y . 34 corresponding European publications . 35 Annex ZA (normative) Normative references to international publications with their 8 BSI 09-2000 STD-BSI BS EN blSbb-3-ENGL 2000 lb2Ybb9 08b9053 182 Page 6 EN 61966
25、-3:2000 MULTIMEDIA SYSTEMS AND EQUIPMENT - COLOURMEASUREMENTANDMANAGEMENT- Part 3: Equipment using cathode ray tubes 1 Scope This part of IEC 61966 deals with equipment using cathode ray tubes (CRT) to display colour images for use in multimedia applications. A series of methods and parameters for c
26、olour measurements and management for use in multimedia systems and equipment is applicable to the assessment of colour reproduction. The methods of measurement standardized in this part are designed to make possible the objective performance assessment and characterization of colour reproduction of
27、 CRT displays which accept red - green - blue analogue or digital signals from electrical input terminals and output colour images on CRT display screens. For CRT displays to which analogue signals are applicable, corresponding digital signals shall be taken into account in applying this part of IEC
28、 61966. The measured results are intended to be used for the purpose of colour management in multimedia systems. This part of IEC 61966 defines input test signals, measurement conditions and methods of measurement, so as to make possible the colour management and comprehensive comparison of the resu
29、lts of measurements. Colour control within equipment is outside the scope of this part of IEC 61966. It does not specify limiting values for various parameters. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of
30、 this part of IEC 61966. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 61966 are encouraged to investigate the possibility of applying the most recent editions of the normative documen
31、ts indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IEC 60050(845): 1987, International Electrotechnical Vocabulary (IEV) - Chapter 845: Lighting 1) IS0 5-4
32、:1995, Photography - Density measurements - Part 4: Geometric conditions for reflection density ISO/CIE 10526:1991, CIE standard colorimetric illuminants ISO/CIE 10527:1991, CIE standard colorimetric observers CIE 15.2:1986, Colorimetry CIE 63:1984, lhe spectroradiometric measurement of light source
33、s IS0 9241 -8:1997, Ergonomic requirements for office work with visual display terminals (VDTs) - Part 8: Requirements for displayed colours 1) This is also CIE Publication 17-4:1987, International Lighting Vocabulary. 8 BSI 09-2000 Page 6 EN 61966-3:2000 Terms and definitions For the purposes of th
34、is part of IEC 61966, the definitions in IEC 60050(845) and the following definitions apply. 3.1 background image on a screen of the CRT display other than test area 3.2 colour patch, test area square colour image on a screen of the CRT display to be measured, in which the input data for the red, gr
35、een and blue channels are kept constant within the image area 3.3 CRT display any multimedia equipment using a cathode ray tube to present colour images for viewing by people 3.4 effective screen height vertical dimension of the area where a picture can be produced 3.5 effective screen width horizon
36、tal dimension of the area where a picture can be produced 3.6 normalised (image) signal input signal divided by its full scale value (see also 5.3) 3.7 uncertainty (of measurement) parameter, associated with the result of a measurement, that characterizes the dispersion of the values that could reas
37、onably be attributed to the particular quantity subject to measure- ment (see also 9*) 4 Letters and symbols The notations consistently adopted in this part of IEC 61966 are summarised below. N The number of bits in digital data for each channel. M Maximum integer for non-negative N-bit system;M = 2
38、N -1. 4, DG, d 2 4h. 5 Conditions 5.1 Environmental conditions All measurements specified in this standard shall be carried out in an area free from signifi- cant electromagnetic fields. All the measurements in this standard, except those in clause 13, shall be performed in a dark room environment.
39、Particular attention should be paid to preventing reflected illumination caused by the ambient objects (desktop, wall, etc.) and direct illumination from light-emitting indicators of measuring instruments. One hour of warm-up time should precede the measurements in 7.2, 9.2, 10.2, 11.2 and 14.2, unl
40、ess otherwise specified by the manufacturer of the equipment. The mains voltage and frequency should be at the rated value specified by the manufacturer of a CRT display. When the mains voltage fluctuates, a regulated power supply shall be used to maintain the supply voltage to within 5 % of the rat
41、ed value. Other environmental conditions such as room temperature and relative humidity shall be reported together with the results of the measurements. If additional environmental conditions are described in the manufacturers specifications, these should be taken into account. 5.2 Conditions of mea
42、surements a) Contrast, brightness and additional adjustments shall be set to the positions specified by the manufacturer of the CRT display under measurement. When the adjustment is not in line with the manufacturers specification, the actual position or corresponding value shall be reported with th
43、e results of the measurements. b) Equipment arrangement for non-contact measurements shall be as shown in Figure I. This arrangement incorporates a spectroradiometer or a non-contact colorimeter, depend- ing on the characteristics to be measured. The instrument optical axis shall be normal to the ce
44、ntre of the surface of the CRT display. The distance d shall be 4h or greater. NOTE It is recommended to take precautions so that the measurement is not influenced by vibration and no picture elements are missing within the field of view of the measuring instrument. Q BSI 09-2000 STD-BSI BS EN bLSbb
45、-3-ENGL 2000 D lb2Libb7 OAb705b 771 W (Measutkg probe) (Main body) Page 8 EN 61966-3:2000 CRT display : I Data generator h - Spectroradbmeter or colorimeter d h IEC 23M h : Effective screen height Figure 1 - Equipment arrangement for non-contact measurements c) The arrangement for contact measuremen
46、ts by colorimeters shall be as shown in Figure 2, where a measurement probe is placed on the CRT face plate. Figure 2 - Equipment arrangement for contact measurements 8 BSI 09-2000 STD=BSI BS EN bLSbb-3-ENGL 2000 2b2qbb9 OBb9057 828 . Page 9 EN 61966-3:2000 d)Test signals applied to red, green and b
47、lue channels shall result in a colour patch of the size shown in Figure 3 on the CRT display. The positioning of the colour patch shall be referred to by the centre as in Figure 3. The background shall be black, unless otherwise specified. - hi5 I- - EC h : Effective screen height Figure 3 - Size of
48、 a colour patch e) The measured area shall be a circular area, centred on the colour patch, with a diameter between 0,05hand 0,15h. NOTE another measure may be used. If the diameter of the area does not meet the requirement for extremely large or small CRT displays, 5.3 Input digital data Relationsh
49、ip between input digital data, any value between 0,l O and 2,O“; c) spectral responsivity compliant to the CIE 2“ colour matching functions as defined in ISOICIE 10527. d) repeatability 0,002 in x , y and 0,5 % for luminance. e) uncertainty 0,005 in CRT and 4 % in luminance in candela per square metre. y for red, green, blue and white of the The ( x, y ) is the CIE 1931 chromaticity coordinate defined in CIE 15.2. NOTE 1 The field of view should be chosen, together with the distance d , so that the measured area on the CRT display meets the requireme
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1