1、BRITISH STANDARDBS EN 62026-1:2007Low-voltage switchgear and controlgear Controller-device interfaces (CDIs) Part 1: General rulesThe European Standard EN 62026-1:2007 has the status of a British StandardICS 29.130.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54
2、g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 62026-1:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2007 BSI 2007ISBN 978 0 580 56435 2National fore
3、wordThis British Standard is the UK implementation of EN 62026-1:2007. It is identical to IEC 62026-1:2007. The UK participation in its preparation was entrusted by Technical Committee PEL/17, Switchgear, controlgear, and HV-LV co-ordination, to Subcommittee PEL/17/2, Low voltage switchgear and cont
4、rolgear.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immuni
5、ty from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 62026-1 NORME EUROPENNE EUROPISCHE NORM September 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektr
6、otechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62026-1:2007 E ICS 29.130.20 English version Low-voltage switchgear and controlgear - Controller-d
7、evice interfaces (CDIs) - Part 1: General rules (IEC 62026-1:2007) Appareillage basse tension - Interfaces appareil de commande-appareil (CDI) - Partie 1: Rgles gnrales (CEI 62026-1:2007) Niederspannungsschaltgerte - Steuerungs-Gerte-Netzwerke (CDIs) - Teil 1: Allgemeine Festlegungen (IEC 62026-1:20
8、07) This European Standard was approved by CENELEC on 2007-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographi
9、cal references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a
10、CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hunga
11、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 17B/1505/CDV, future edition 2 of IEC 62026-1, prepared by SC 17B, Low-voltage s
12、witchgear and controlgear, of IEC TC 17, Switchgear and controlgear, was submitted to the IEC-CENELEC parallel Unique Acceptance Procedure and was approved by CENELEC as EN 62026-1 on 2007-09-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by p
13、ublication of an identical national standard or by endorsement (dop) 2008-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2010-09-01 This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the Europ
14、ean Free Trade Association and covers essential requirements of EC Directives EMC (89/336/EEC) and EMC2 (2004/108/EC). See Annex ZZ. Annexes ZA and ZZ have been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62026-1:2007 was approved by CENELEC as a European Standa
15、rd without any modification. _ EN 62026-1:2007 2 CONTENTS INTRODUCTION.4 1 Scope.5 2 Normative references5 3 Terms and definitions .6 4 Classifications 7 5 Characteristics7 5.1 CDI components7 5.2 Interfaces 7 5.3 Topology .8 5.4 Information exchanges.8 5.5 Attributes.8 6 Product information.8 6.1 I
16、nstructions for installation, operation and maintenance8 6.2 Profiles8 6.3 Marking .8 6.4 Degree of protection 9 7 Normal service, mounting and transport conditions9 7.1 General .9 7.2 Normal service conditions9 7.2.1 General .9 7.2.2 Ambient air temperature.9 7.2.3 Altitude 9 7.2.4 Climatic conditi
17、ons.9 7.3 Conditions during transport and storage.9 7.4 Mounting .10 8 Constructional and performance requirements 10 8.1 General .10 8.2 Electromagnetic compatibility (EMC)10 8.2.1 Immunity10 8.2.2 Emission11 8.2.3 EMC tests11 9 Tests 11 9.1 General .11 9.2 Type tests .11 9.3 Electromagnetic compat
18、ibility.11 Table 1 Immunity requirements 10 EN 62026-1:2007 3 Annex ZA (normative) Normative references to international publications with theircorresponding European publications .13 Annex ZZ (informative) Coverage of Essential Requirements of EC Directives .14INTRODUCTION The class of controller-d
19、evice interfaces (CDIs) covered in this International Standard includes industrial CDIs for control systems, factory automation and process automation. Industrial CDIs have proliferated to meet specific user needs, but no single CDI meets all needs. The reason for multiple solutions is the wide rang
20、e of physical, usage, information content and configuration requirements. The physical requirements have resulted in CDIs with widely differing signal and line conditioning mechanisms in order to meet distance, node count and environmental considerations. While there is wide variation in CDI technol
21、ogies, there are common components, interfaces and environmental requirements that are specified by this standard. Standardized definitions of these common CDI requirements assist the user to compare and select technologies to match the distance, node count, throughout and installation requirements
22、for a specific application. This standard simplifies the CDI selection process by providing a common structure for generating a specific CDIs IEC standard while also allowing specific interface features and capabilities to be included. Clauses 1 to 8 contain the outline of general requirements that
23、the CDIs IEC standard identifies. Clause 9 contains the test specification. Standardization of CDI aspects also simplifies the task of writing the software for the higher layer functions of industrial control systems, such as supervisory control, operator interface and control strategy programming.
24、For this standard to be complete and usable, it requires the availability of specific CDI standards, which make up the other parts of the IEC 62026 series. EN 62026-1:2007 4 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR CONTROLLER-DEVICE INTERFACES (CDIs) Part 1: General rules 1 Scope This International St
25、andard applies to interfaces between low-voltage switchgear, controlgear, and controllers (e.g. programmable controllers, personal computers, etc.). This standard does not apply to higher level industrial communication networks that have become known as fieldbuses and are considered by IEC subcommit
26、tee 65C. The purpose of this standard is to harmonize and define rules, components and requirements of a general nature applicable to industrial CDIs. Those features of the various CDI standards which can be considered as general have therefore been brought together in this part of IEC 62026. For ea
27、ch CDI, two main documents are necessary to determine all requirements and tests: a) this part, referred to as “IEC 62026-1” or “Part 1” in the relevant CDI parts covering the various types of CDIs; b) the specific CDI part of the IEC 62026 series. A specific CDI part may omit a general requirement
28、if it is not applicable, or it may add to it if it is inadequate in the particular case, but it should not deviate from the requirement unless there is substantial technical justification. NOTE Product-specific requirements for products incorporating a CDI are given in the relevant product standards
29、. These requirements apply in addition to those given in this International Standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of
30、the referenced document (including any amendments) applies. IEC 60947-1:2007, Low-voltage switchgear and controlgear Part 1: General rules IEC 61000-4-2:1995, Electromagnetic compatibility (EMC) Part 4-2: Testing and measure-ment techniques Electrostatic discharge immunity test Amendment 1 (1998) Am
31、endment 2 (2000) IEC 61000-4-3:2006, Electromagnetic compatibility (EMC) Part 4-3: Testing and measure-ment techniques Radiated radio-frequency electromagnetic field immunity test IEC 61000-4-4:2004, Electromagnetic compatibility (EMC) Part 4-4: Testing and measure-ment techniques Electrical fast tr
32、ansient/burst immunity test IEC 61000-4-5:2005, Electromagnetic compatibility (EMC) Part 4-5: Testing and measure-ment techniques Surge immunity test EN 62026-1:2007 5 EC 61000-4-6:2003, Electromagnetic compatibility (EMC) Part 4-6: Testing and measurement techniques Immunity to conducted disturbanc
33、es, induced by radio-frequency fields Amendment 1 (2004) Amendment 2 (2006) IEC 61000-6-2:2005, Electromagnetic compatibility (EMC) Part 6-2: Generic standards Immunity for industrial environments CISPR 11:2003, Industrial, scientific and medical (ISM) radio-frequency equipment Electromagnetic distu
34、rbance characteristics Limits and methods of measurement Amendment 1 (2004) Amendment 2 (2006) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 change of state process of data exchange which occurs only when a devices or controllers data chang
35、es state according to specific change criteria 3.2 controller programmable controller, personal computer or equivalent computing hardware in which the software controlling the application or process runs 3.3 controller-device communication medium means (such as two or more wires or fibre optic cable
36、) utilized by devices or controllers to transfer data to other devices or controllers NOTE A CDI that has “power on the communication medium“ architecture uses two wires that also distribute power within the CDI. 3.4 controller-device interface (CDI) arrangement of nodes and their interconnections t
37、hat transport information between controllers and devices in an industrial control system 3.5 CDI component device, controller or other component for which the requirements are specified in a CDI part 3.6 CDI power supply power supply with characteristics and parameters suitable for the CDIs functio
38、nality and capability 3.7 CDI power distribution medium inter-connecting means used to transfer power within a CDI NOTE In the case of a CDI that has “power on the communication medium“ architecture, the CDI power distribution medium also transfers data within the CDI. EN 62026-1:2007 6 3.8 device p
39、hysical unit containing application elements and that may contain communication elements EXAMPLES: Control circuit device (see 2.2.16 of IEC 60947-1), presence sensing device, pressure sensing device, actuator, annunciator, operator terminal, motor controller, current sensor, valve control, data log
40、ger, bar-code scanner, push-button, pilot light, etc. 3.9 device profile representation of device functionality available to the CDI 3.10 multicast process of data exchange which occurs when a device or controller produces one message to multiple devices and/or controllers for their appropriate acti
41、on 3.11 polling process of data exchange which occurs when a device or a controller sends data to, or requests data from, a specific device or controller NOTE The receiving device responds to the polling by acting according to the data it receives or by returning its status data. When this transacti
42、on is completed, the device polls the next device in a predetermined sequence. 3.12 strobing process of data exchange which occurs when a device or a controller sends a single request for data from one or more devices and/or controllers NOTE Each device receiving the message then responds with its r
43、equested data in a predetermined sequence. 4 Classifications This clause in the specific CDI parts shall list the classifications below, where applicable, with appropriate details: CDI components; interfaces; topology; information exchanges; attributes. 5 Characteristics This clause in the specific
44、CDI parts shall list the applicable characteristics described below with appropriate details. 5.1 CDI components Specific CDI parts shall specify requirements for the devices, controllers and other components that may be used. 5.2 Interfaces Specific CDI parts shall include information on the follow
45、ing, if applicable: EN 62026-1:2007 7 procedural, such as what needs to happen first, second, etc. when the interface system powers up and down, and establishes and terminates data exchange across the interface; information exchanges, such as what a device is requested to do across an interface; EXA
46、MPLE 1 Polling, change of state. services and protocol, i.e. the message structure and content that crosses the interface; EXAMPLE 2 Peer-to-peer, master-slave. device and controller behaviour as viewed from the CDI; mechanical, i.e. the shape, construction, pin size, etc.; electrical, such as the v
47、oltage, current and timing of the bit levels on the CDI; functional, i.e. what interface connections provide which functions. 5.3 Topology Specific CDI parts shall specify the topologies that may be used. EXAMPLE Daisy chain, star, tree, trunk/drop. 5.4 Information exchanges Specific CDI parts shall
48、 specify the information exchanges that may be used. 5.5 Attributes Specific CDI parts shall specify the applicable attribute values including as a minimum: data transmission rate (in bits per second); maximum length of communication medium or end to end distance; message length for single transmiss
49、ion; EXAMPLE 4 bits, 8 bytes. maximum node count per system; and other information to support the evaluation of the transmission time of the CDI. 6 Product information 6.1 Instructions for installation, operation and maintenance The manufacturer shall specify in the documents or catalogues, the conditions for installation, operation and maintenance of the CDI components. The instructions shall specify the measures to be taken, if any, for achieving EMC compliance as d
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1