EN 62282-6-200-2017 en Fuel cell technologies - Part 6-200 Micro fuel cell power systems - Performance test methods.pdf

1、Fuel cell technologiesPart 6-200: Micro fuel cell power systems Performance test methodsBS EN 62282-6-200:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN 62282-6-200:2017. Itis identical to IEC

2、 62282-6-200:2016. It supersedes BS EN 62282-6-200:2012which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/105, Fuel cell technologies.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does

3、 not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 86725 5ICS 27.070Compliance with a British Standard cannot confer immunity fromlegal obli

4、gations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62282-6-200:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62282-6-200 Janu

5、ary 2017 ICS 27.070 Supersedes EN 62282-6-200:2012 English Version Fuel cell technologies - Part 6-200: Micro fuel cell power systems - Performance test methods (IEC 62282-6-200:2016) Technologies des piles combustible - Partie 6-200: Systmes micropiles combustible - Mthodes dessai des performances

6、(IEC 62282-6-200:2016) Brennstoffzellentechnologien - Teil 6-200: Mikro-Brennstoffzellen-Energiesysteme - Leistungskennwerteprfverfahren (IEC 62282-6-200:2016) This European Standard was approved by CENELEC on 2016-10-27. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations

7、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.

8、This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. C

9、ENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Nethe

10、rlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Manag

11、ement Centre: Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 62282-6-200:2017 E BS EN 62282-6-200:2017EN 62282-6-200:2017 2 European foreword The text of document 105/527/CDV, future edition 3

12、 of IEC 62282-6-200, prepared by IEC/TC 105 “Fuel cell technologies“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62282-6-200:2017. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical

13、national standard or by endorsement (dop) 2017-07-27 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-10-27 This document supersedes EN 62282-6-200:2012. Attention is drawn to the possibility that some of the elements of this document may be t

14、he subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62282-6-200:2016 was approved by CENELEC as a European Standard without any modification. BS EN 62282-6-200:2017E

15、N 62282-6-200:2017 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only

16、the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on th

17、e latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) EN 60068-2-6 - IEC 60721-3-7 - Classification of environmental conditions -

18、Part 3: Classification of groups of environmental parameters and their severities - Section 7: Portable and non-stationary use EN 60721-3-7 - IEC/TS 62282-1 2013 Fuel cell technologies - Part 1: Terminology - - ISO/IEC 17025 - General requirements for the competence of testing and calibration labora

19、tories EN ISO/IEC 17025 - BS EN 62282-6-200:2017 2 IEC 62282-6-200:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms and definitions 7 4 General principles . 8 4.1 Testing environment 8 4.2 Minimum required measurement accuracy . 8 4.3 Measuring instrum

20、ents 9 4.3.1 General . 9 4.3.2 Voltage 9 4.3.3 Current 9 4.3.4 Time 9 4.3.5 Weight . 9 4.3.6 Temperature 9 4.3.7 Humidity 9 4.3.8 Pressure 9 4.3.9 Vibration frequency 9 4.3.10 Volume 9 5 Tests . 10 5.1 Test procedure 10 5.2 Power generation characteristics . 10 5.2.1 Starting duration 10 5.2.2 Rated

21、 power test and rated voltage test 10 5.2.3 Power generation test after idle condition . 10 5.2.4 Power generation test at low and high temperatures . 11 5.2.5 Power generation test under low and high humidity conditions 11 5.2.6 Altitude test . 11 5.3 Mechanical durability tests 12 5.3.1 Drop test

22、12 5.3.2 Vibration test . 12 6 Labelling and marking 13 7 Test report 13 Bibliography . 17 Figure 1 Micro fuel cell power system block diagram . 6 Table 1 Drop height . 12 Table 2 Vibration condition . 13 Table 3 Test report of micro fuel cell power system Performance test . 14 BS EN 62282-6-200:201

23、7IEC 62282-6-200:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FUEL CELL TECHNOLOGIES Part 6-200: Micro fuel cell power systems Performance test methods FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all nation

24、al electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical

25、Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Int

26、ernational, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The f

27、ormal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations

28、 for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user

29、. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication s

30、hall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent cer

31、tification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal i

32、njury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative reference

33、s cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for iden

34、tifying any or all such patent rights. International Standard IEC 62282-6-200 has been prepared by IEC technical committee 105: Fuel cell technologies. This third edition cancels and replaces the second edition, published in 2012. This edition constitutes a technical revision. This edition includes

35、the following significant technical changes with respect to the previous edition: a) deletion of 5.3 (Fuel consumption test) as it was impractical to measure the actual consumption rate of some kinds of fuels; b) addition and modification of some terms and definitions. BS EN 62282-6-200:2017 4 IEC 6

36、2282-6-200:2016 IEC 2016 The text of this standard is based on the following documents: CDV Report on voting 105/527/CDV 105/545A/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted

37、in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62282 series, published under the general title Fuel cell technologies, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date in

38、dicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 62282-6-200:2017IEC 62282-6-200:2016 IEC 2016 5 INTRODUCTION With advancements in

39、technology, the expectation or demand for the commercial introduction of fuel cells has increased dramatically in recent years. It is especially strong for micro fuel cell power systems intended for applications in laptop computers, mobile phones, personal digital assistants (PDAs), cordless home ap

40、pliances, TV broadcast cameras, autonomous robots, etc. The essential component of a micro fuel cell power system is its power unit. Some micro fuel cell power systems have built-in power units and others have external power units. BS EN 62282-6-200:2017 6 IEC 62282-6-200:2016 IEC 2016 FUEL CELL TEC

41、HNOLOGIES Part 6-200: Micro fuel cell power systems Performance test methods 1 Scope This part of IEC 62282 specifies test methods for the performance evaluation of micro fuel cell power systems for laptop computers, mobile phones, personal digital assistants (PDAs), cordless home appliances, TV bro

42、adcast cameras, autonomous robots, etc. This document describes the performance test methods for power characteristics, and mechanical durability for micro fuel cell power systems with output up to 60 V DC and 240 VA. The functional arrangement of a typical example of a micro fuel cell power system,

43、 evaluated according to this document, is shown in Figure 1. This document does not address the safety of micro fuel cell power systems. This document does not address the interchangeability of micro fuel cell power systems. Figure 1 Micro fuel cell power system block diagram 2 Normative references

44、The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition IEC Aqueous reservoir/ Water cartridge (optional) Fuel reservoir Optional combined cartridge housing Fuel cartridge Ai

45、r Micro fuelcell power system Waste reservoir (optional) Waste cartridge (optional) Internal power needs (optional) Power conditioning Primary or secondary battery or capacitor (optional) Water/byproduct management Micro fuel cell or micro fuel cell module Thermal management Internal reservoir (opti

46、onal) Fuel management system Control system Balance of plant Air management system Micro fuel cell power unit Aqueous supply (optional) Fuel supply Water/ byproduct discharge Power output Waste heat External control BS EN 62282-6-200:2017IEC 62282-6-200:2016 IEC 2016 7 cited applies. For undated ref

47、erences, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal) IEC 60721-3-7, Classification of environmental conditions Part 3-7: Classification of groups of environmental parameters and

48、 their severities Portable and non-stationary use IEC TS 62282-1:2013, Fuel cell technologies Part 1: Terminology ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories 3 Terms and definitions For the purposes of this document, the terms and definitions given

49、in IEC TS 62282-1:2013 and the following apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp NOTE Some terms have been taken from IEC TS 62282-1 and modified for the needs of this document. 3.1 conditioning placing the micro fuel cell power system in the pre-generation state in the