EN 62310-3-2008 en Static transfer systems (STS) - Part 3 Method for specifying performance and test requirements《静态转换系统(STS) 第3部分 性能和实验要求的规定方法》.pdf

1、Static transfer systems (STS) Part 3: Method for specifying performanceand test requirementsBS EN 62310-3:2008raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI British StandardsNational forewordThis British Standard is the UK implementation of EN 62

2、310-3:2008. It isidentical to IEC 62310-3:2008.The UK participation in its preparation was entrusted to Technical CommitteePEL/22, Power electronics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the n

3、ecessary provisions of acontract. Users are responsible for its correct application. BSI 2009ISBN 978 0 580 57791 8ICS 29.200; 29.240.30BRITISH STANDARDBS EN 62310-3:2008Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the auth

4、ority of the StandardsPolicy and Strategy Committee on 30 April 2009Amendments issued since publicationAmd. No. Date Text affectedEUROPEAN STANDARD EN 62310-3 NORME EUROPENNE EUROPISCHE NORM September 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation

5、 Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62310-3:2008 E ICS 29.200; 29.240.30 English versio

6、n Static transfer systems (STS) - Part 3: Method for specifying performance and test requirements (IEC 62310-3:2008) Systmes de transfert statique (STS) - Partie 3: Mthode de spcification des performances et exigences dessai (CEI 62310-3:2008) Statische Transfersysteme - Teil 3: Verfahren fr die Fes

7、tlegung des Betriebsverhaltens und Prfanforderungen(IEC 62310-3:2008) This European Standard was approved by CENELEC on 2008-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

8、standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any

9、 other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech R

10、epublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 62310-3:2008 - 2 - Foreword The text of d

11、ocument 22H/105/FDIS, future edition 1 of IEC 62310-3, prepared by SC 22H, Uninterruptible power systems (UPS), of IEC TC 22, Power electronic systems and equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62310-3 on 2008-07-01. The following dates were fixed

12、: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-07-01 Annex ZA has been added by CENELEC. _ En

13、dorsement notice The text of the International Standard IEC 62310-3:2008 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60664-3 NOTE Harmonized as HD 625.3 S1:19

14、97 (not modified). HD 625.3 S1 is superseded by EN 60664-3:2003 which is based on IEC 60664-3:2003. IEC 60947-1 NOTE Harmonized as EN 60947-1:2007 (not modified). IEC 60990 NOTE IEC 60990:1990 is superseded by IEC 60990:1999, which is harmonized as EN 60990:1999 (not modified). IEC 61140 NOTE Harmon

15、ized as EN 61140:2002 (not modified). IEC 61400-1 NOTE Harmonized as EN 61400-1:2005 (not modified). IEC 62040-2 NOTE Harmonized as EN 62040-2:2006 (not modified). IEC 62040-1-1 NOTE Harmonized as EN 62040-1-1:2003 (not modified). IEC 62040-1-2 NOTE Harmonized as EN 62040-1-2:2003 (not modified). _

16、BS EN 62310-3:2008- 3 - EN 62310-3:2008 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited appli

17、es. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60068 Series Environme

18、ntal testing EN 60068 Series IEC 60146-1-1 -1)Semiconductor convertors - General requirements and line commutated convertorsPart 1-1: Specification of basic requirements EN 60146-1-1 19932)IEC 60439-1 -1)Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-teste

19、d assemblies EN 60439-1 19992)IEC 60529 -1)Degrees of protection provided by enclosures (IP Code) EN 60529 + corr. May 19912)1993 IEC 60947-6-1 -1)Low-voltage switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer switching equipment EN 60947-6-1 20052)IEC 60950-1 (mod) -1)Inf

20、ormation technology equipment - Safety - Part 1: General requirements EN 60950-1 20062)IEC 61000-2-2 -1)Electromagnetic compatibility (EMC) - Part 2-2: Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems EN 61000-2-2 2

21、0022)IEC 62040-3 (mod) -1)Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements EN 62040-3 20012)IEC 62310-1 -1)Static transfer systems (STS) - Part 1: General and safety requirements EN 62310-1 20052)IEC 62310-2 (mod) -1)Static transfer systems (ST

22、S) - Part 2: Electromagnetic compatibility (EMC) requirements EN 62310-2 20072)ISO 7779 -1)Acoustics - Measurement of airborne noise emitted by information technology and telecommunications equipment EN ISO 7779 20012)1)Undated reference. 2)Valid edition at date of issue. 2 62310-3 IEC:2008 CONTENTS

23、 1 Scope.6 2 Normative references .6 3 Terms and definitions .7 3.1 General definitions 7 3.2 Specified values 10 3.3 Input values.11 3.4 Output values11 4 Performance requirements .12 4.1 Declared electrical characteristics .12 4.1.1 Performance classification.12 4.1.2 Main electrical characteristi

24、cs13 4.2 Normal service conditions .14 4.3 Transfer characteristics .14 4.3.1 Load voltage14 4.3.2 Cross-current 15 4.4 Neutral management .15 4.4.1 Common neutral 15 4.4.2 Separately derived neutrals .15 4.4.3 Neutral current 15 4.4.4 Protective earth current .15 4.5 Performance requirements to be

25、identified by the purchaser .16 5 STS tests .16 5.1 General .16 5.1.1 Type tests .16 5.1.2 Routine tests .16 5.1.3 Site tests .16 5.1.4 Testing schedule .16 5.2 Electrical tests.18 5.2.1 Insulation and dielectric.18 5.2.2 Light load and functional test.18 5.2.3 No load19 5.2.4 Rated load.19 5.2.5 Tr

26、ansfer.19 5.2.6 Source tolerance .21 5.2.7 Overload and fault current .21 5.2.8 Operating losses .23 5.2.9 Backfeed .24 5.2.10 Abnormal operating conditions 25 5.3 Transportation and environment 26 5.3.1 General .26 5.3.2 Impact and shock 26 5.3.3 Free fall.26 5.3.4 Storage .27 5.3.5 Temperature and

27、 humidity .28 5.3.6 Acoustic noise .28 BS EN 62310-3:200862310-3 IEC:2008 3 Annex A (normative) Reference load29 Annex B (normative) STS voltage sensing tolerance33 Annex C (informative) Neutral management in static transfer systems .35 Annex D (normative) Neutral switching in static transfer system

28、s Additional requirements.37 Annex E (informative) Purchaser specification guidelines 39 Annex F (informative) Output short circuit test procedure.43 Annex G (normative) Backfeed protection test .47 Annex H (normative) Minimum and maximum cross-sections of copper conductors suitable for connection48

29、 Bibliography49 Figure 1 Complying load current flow - Common grounding of a.c. input sources - common STS neutral 15 Figure 2 Objectionable load current flow - Independent grounding of a.c. input sources - common STS neutral .16 Figure 3 STS cross current test20 Figure 4 Typical circuit for measuri

30、ng conduction losses24 Figure B.1 Source tolerance classification 1.33 Figure B.2 Source tolerance classification 2.34 Figure B.3 Source tolerance classification 3.34 Figure B.4 Source tolerance classification 4.34 Figure C.1 Continuous STS neutral with common grounding of a.c. input sources (comply

31、ing load current flow) 35 Figure C.2 Continuous STS neutral with independent grounding of a.c. input sources + isolation transformer (complying load current flow) 36 Figure C.3 Switched STS with independent grounding of a.c. input sources (complying steady state load current flow) 36 Figure D.1 Load

32、 voltage variation upon neutral switch failure.37 Figure D.2 Overlapping switched STS neutral 38 Figure F.1 Test circuit for STS output withstand current.45 Table 1 Transfer interruption classification “T” .13 Table 2 Tests for STS performance characteristics 17 Table 3 Short time withstand current2

33、2 Table 4 Free fall testing .27 Table E.1 STS technical data sheet .41 Table F.1 Values of power-factors and time-constants corresponding to test currents and ratio n between peak and r.m.s. values of current 44 Table H.1 Minimum and maximum cross-sections of copper conductors suitable for connectio

34、n (extract from IEC 60439-1)48 BS EN 62310-3:2008 6 62310-3 IEC:2008 STATIC TRANSFER SYSTEMS (STS) Part 3: Method for specifying performance and test requirements 1 Scope The IEC 62310 series of three standards applies to stand-alone operating a.c. static transfer systems (STS) intended to ensure th

35、e continuity of load supply through controlled transfer, with or without interruption of power, from two or more independent a.c. sources. This series of standards includes information for the overall integration of the STS and its accessories into the a.c. power network and includes requirements fo

36、r the switching elements, their control and protective elements, where applicable. Part 1 of the series concerns general and safety requirements. Part 2 of the series concerns electromagnetic compatibility (EMC) requirements. This Part 3 of the series concerns methods for specifying performance and

37、test requirements including applicable safety tests referenced in standard IEC 62310-1 for general and safety requirements. This standard applies for single-phase, phase-phase and three-phase static transfers in a. c. systems up to 1 000 V. It takes precedence over all aspects of generic performance

38、 standards, and no additional performance testing is necessary. The requirements have been selected so as to be consistent with compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems (see IEC 61000-2-2) as well as to ensure an adequate

39、 level of performance when the STS is applied in diverse critical load situations. The requirements take into account the differing test conditions necessary to encompass the range of physical sizes and power ratings of STS. This standard applies to STS as a stand-alone product, whether presented as

40、 a unit or an assembly of units. This standard does not apply to: devices for d.c. source switching; single source systems; transfer systems using only electromechanical switching devices with interruption of the supply to the load during transfer and intended to be used in emergency power systems o

41、r covered by IEC 60947-6-1; automatic switching devices integrated into UPS covered by the IEC 62040 series of UPS product standards. NOTE Additional or different requirements may apply to STS intended for use on board of vehicles including ships and aircrafts, in emergency power systems subject to

42、a particular regulation e.g. health care facilities, fire fighting or emergency rescue, in tropical countries or where elevations are greater than 1 000 m. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

43、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068 (all parts), Environmental testing BS EN 62310-3:200862310-3 IEC:2008 7 IEC 60146-1-1, Semiconductor convertors General requirements and line commutated convert

44、ors Part 1-1: Specifications of basic requirements IEC 60439-1, Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type-tested assemblies IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 60947-6-1, Low-voltage switchgear and controlgear Part 6-1:

45、 Multiple function equipment Transfer switching equipment IEC 60950-1, Information technology equipment Safety Part 1: General requirements IEC 61000-2-2, Electromagnetic compatibility (EMC) Part 2-2: Environment Compatibility levels for low-frequency conducted disturbances and signalling in public

46、low-voltage power supply systems IEC 62040-3, Uninterruptible power systems (UPS) Part 3: Method of specifying the performance and test requirements IEC 62310-1, Static Transfer Systems (STS) Part 1: General and safety requirements IEC 62310-2, Static Transfer Systems (STS) Part 2: Electromagnetic C

47、ompatibility (EMC) requirements ISO 7779, Measurement of airbone noise emitted by information technology and telecommunications equipment 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 General definitions 3.1.1 static transfer system (STS) s

48、ystem that transfers a load, by static means, between a preferred source and an alternate source NOTE 1 The transfer may be automatic and/or manual. NOTE 2 The transfer may be with or without interruption. 3.1.2 power pole or electronic power switch in the context of this standard, an operative unit

49、 for electronic power switching comprising at least one controlled electronic valve device IEV 551-13-01, modified 3.1.3 primary circuit internal circuit which is directly connected to the external supply source which supplies the electric power to the load. It includes the primary windings of transformers, motors, other loading devices and the means of connection to the supply source. BS EN 62310-3:2008 8 62310-3 IEC:2008