EN 62343-4-1-2016 en Dynamic modules - Part 4-1 Software and hardware interface - 1 x 9 wavelength selective switch.pdf

1、Dynamic modulesPart 4-1: Software and hardware interface 1 x 9 wavelength selective switchBS EN 62343-4-1:2016BSI Standards PublicationNational forewordThis British Standard is the UK implementation of EN 62343-4-1:2016. It isidentical to IEC 62343-4-1:2016.The UK participation in its preparation wa

2、s entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/3, Fibre optic systems and active devices.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa cont

3、ract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85515 3ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the auth

4、ority of theStandards Policy and Strategy Committee on 31 May 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62343-4-1:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62343-4-1 May 2016 ICS 33.180.20 English Version Dynamic modules - Part 4-1: Sof

5、tware and hardware interface - 1 x 9 wavelength selective switch (IEC 62343-4-1:2016) Modules dynamiques - Partie 4-1 : Interface logicielle et matrielle - Commutateur slectif en longueur donde 1 x 9 (IEC 62343-4-1:2016) Dynamische Module - Teil 4-1: Software und Hardware Schnittstelle - 1 x 9 Welle

6、nlngenselektiver Schalter (IEC 62343-4-1:2016) This European Standard was approved by CENELEC on 2016-04-08. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any al

7、teration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other langua

8、ge made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the C

9、zech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

10、Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means rese

11、rved worldwide for CENELEC Members. Ref. No. EN 62343-4-1:2016 EBS EN 62343-4-1:2016EN 62343-4-1:2016 2 European foreword The text of document 86C/1304/CDV, future edition 1 of IEC 62343-4-1, prepared by SC 86C “Fibre optic systems and active devices” of IEC/TC 86 “Fibre optics” was submitted to the

12、 IEC-CENELEC parallel vote and approved by CENELEC as EN 62343-4-1:2016. The following dates are fixed: g120 latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-01-08 g120 latest date by which the nat

13、ional standards conflicting with the document have to be withdrawn (dow) 2019-04-08 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. En

14、dorsement notice The text of the International Standard IEC 62343-4-1:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated : IEC 62343-3-3 NOTE Harmonized as EN 62343-3-3

15、. BS EN 62343-4-1:2016EN 62343-4-1:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For da

16、ted references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-d

17、ate information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 60050-731 - International Electrotechnical Vocabulary - Chapter 731: Optical fibre communication - - IEC 62343 - Dynamic modules - General and

18、 guidance EN 62343 - BS EN 62343-4-1:2016 2 IEC 62343-4-1:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms, definitions and abbreviations 6 3.1 Terms and definitions 6 3.2 Abbreviations 6 4 Basic configuration of WSS interface 7 5 Software interface .

19、8 6 Hardware interface Electrical connector 11 (informative) Hardware interface details 12 Annex A(informative) DPRAM memory map details and timing charts . 14 Annex BBibliography . 30 Figure 1 Basic configuration of WSS interface 7 Figure B.1 DPRAM READ CYCLE timing 25 Figure B.2 DPRAM WRITE CYCLE

20、timing . 26 Figure B.3 POWER ON timing 26 Figure B.4 START timing 27 Figure B.5 MASTER RESET timing 27 Figure B.6 SOFT RESET timing . 28 Figure B.7 DPRAM BUSY timing 28 Figure B.8 ALARM timing . 29 Table 1 Software interface . 9 Table 2 DPRAM memory map 10 Table A.1 Connector form 12 Table A.2 Pin a

21、ssignment 12 Table A.3 Supply voltages and currents 13 Table A.4 Low voltage TTL thresholds 13 Table A.5 Power consumption 13 Table B.1 DPRAM memory map specification A 14 Table B.2 DPRAM memory map specification B 15 Table B.3 Signal time specification . 24 BS EN 62343-4-1:2016IEC 62343-4-1:2016 IE

22、C 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DYNAMIC MODULES Part 4-1: Software and hardware interface 1 x 9 wavelength selective switch FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical co

23、mmittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Techni

24、cal Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, government

25、al and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agr

26、eements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use

27、 and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promo

28、te international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indica

29、ted in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6)

30、All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage

31、 or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this public

32、ation. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all suc

33、h patent rights. International Standard IEC 62343-4-1 has been prepared by subcommittee SC86C: Fibre optic systems and active devices, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: CDV Report on voting 86C/1304/CDV 86C/1346/RVCFull inform

34、ation on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62343 series, published under the general title Dynamic modules

35、, can be found on the IEC website. BS EN 62343-4-1:2016 4 IEC 62343-4-1:2016 IEC 2016 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publicat

36、ion. At this date, the publication will be g120 reconfirmed, g120 withdrawn, g120 replaced by a revised edition, or g120 amended. A bilingual version of this publication may be issued at a later date. BS EN 62343-4-1:2016IEC 62343-4-1:2016 IEC 2016 5 INTRODUCTION A wavelength selective switch (WSS)

37、is a dynamic module, which is mainly used in a reconfigurable optical add drop multiplexer (ROADM) system to switch all wavelength signals to their respective required output port in dense wavelength division multiplexing (DWDM) networks. The WSS module has one input port and a plurality of output p

38、orts (i.e. 1 x N WSS) and can be used reversely, such as N input ports and one output port, depending on its application. It is electrically controlled with software, which directs each wavelength signal among an input DWDM signal from one input port to the required output port for each wavelength s

39、ignal. BS EN 62343-4-1:2016 6 IEC 62343-4-1:2016 IEC 2016 DYNAMIC MODULES Part 4-1: Software and hardware interface 1 x 9 wavelength selective switch 1 Scope This part of IEC 62343 describes and provides specifications for a software and hardware interface for the 1 x 9 wavelength selective switch.

40、These switches can be controlled by resident firmware with this interface. This standard addresses the configuration and function to control a WSS. This interface is intended to enable a user or host to retrieve the switch status and/or adjust relevant switch and attenuation settings. 2 Normative re

41、ferences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

42、. IEC 60050-731, International Electrotechnical Vocabulary Chapter 731: Optical fibre communication (available at http:/www.electropedia.org) IEC 62343, Dynamic modules - General and guidance 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the term

43、s and definitions given in IEC 60050-731 and IEC 62343, as well as the following apply. 3.1.1 wavelength selective switch WSS dynamic module with one or more input ports and one or more output ports, which is mainly used in a reconfigurable optical add drop multiplexer (ROADM) system to switch each

44、wavelength signal on each input port independently to its required output port in DWDM networks Note 1 to entry: It is electrically controlled with software. Note 2 to entry: It can be used inverted, exchanging input and output ports. Note 3 to entry: Each wavelength signal can be independently atte

45、nuated. 3.2 Abbreviations For the purposes of this document, the following abbreviations apply. DWDM dense wavelength division multiplexing WSS wavelength selective switch BS EN 62343-4-1:2016IEC 62343-4-1:2016 IEC 2016 7 ROADM reconfigurable optical add drop multiplexer HC host controller DPRAM dua

46、l-port RAM FPGA field programmable gate array DSP digital signal processor R/W read or write RW read and write RO read only CE chip enable OE output enable TxD transmitted data RxD received data 4 Basic configuration of WSS interface The software interface is intended to provide an access to the fun

47、ctions of the WSS module and be the primary interface to command the unit. The HC controls the WSS module by sending control signal, as well as command data, to the WSS module via a 12-bit address bus, a 16-bit data bus, and DPRAM related signal lines such as Read/Write, Chip Enable, and Output Enab

48、le. The HC also receives from the WSS module response signals and status data. Any address within the DPRAM can be written to via the HC, however many of these values will be overwritten upon the application of a command to the WSS module. The addresses, which are identified as inputs, can be found

49、further along in this document. In addition to the DPRAM interface, RS232 serial communication is also supported by the WSS module. The WSS module has a non-volatile memory to store the latest setting when requested. A functional diagram of the WSS module controls is illustrated in Figure 1 below. Figure 1 Basic configuration of WSS interface Interface DSP/ FPGA DPRAM Address bus (12) DPRAM Date bus (16) DPRAM Control RS232C RxD RS232C TxD MASTER RESET SOFT RESET HC