EN 62496-3-2011 en Optical circuit boards - Part 3 Performance standards - General and guidance《光学电路板 第3部分 性能标准 总则和指南》.pdf

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication Optical circuit boards Part 3: Performance standards General and guidance BS EN 62496-3:2011National foreword This British Standard is the UK implementation of EN 62496-3:2011

2、. It is identical to IEC 62496-3:2011. The UK participation in its preparation was entrusted to Technical Committee GEL/86, Fibre optics. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary

3、provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 68356 5 ICS 31.180; 33.180.01 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Str

4、ategy Committee on 31 March 2011. Amendments issued since publication Amd. No. Date Text affected BRITISH STANDARD BS EN 62496-3:2011 EUROPEAN STANDARD EN 62496-3 NORME EUROPENNE EUROPISCHE NORM February 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisat

5、ion Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62496-3:2011 E ICS 33.180.01 English version Optical

6、 circuit boards - Part 3: Performance standards - General and guidance (IEC 62496-3:2011) Cartes circuits optiques - Partie 3: Normes de performance - Gnralits et guide (CEI 62496-3:2011) Optische Leiterplatten - Teil 3: Betriebsverhalten - Allgemeines und Leitfaden (IEC 62496-3:2011) This European

7、Standard was approved by CENELEC on 2011-02-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references con

8、cerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member int

9、o its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icela

10、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 62496-3:2011EN 62496-3:2011 - 2 - Foreword The text of document 86/380/FDIS, future edition 1 of IEC 62496-3, pre

11、pared by IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62496-3 on 2011-02-16. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsibl

12、e for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-11-16 latest date by which the national standards conflicting with the EN

13、 have to be withdrawn (dow) 2014-02-16 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62496-3:2011 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be a

14、dded for the standards indicated: IEC 60068-2-27 NOTE Harmonized as EN 60068-2-27. IEC 60068-2-32 NOTE Harmonized as EN 60068-2-32. IEC 61300 series NOTE Harmonized in EN 61300 series (not modified). IEC 61751 NOTE Harmonized as EN 61751. IEC 62005 series NOTE Harmonized in EN 62005 series (not modi

15、fied). IEC 60529 NOTE Harmonized as EN 60529. _ BS EN 62496-3:2011 - 3 - EN 62496-3:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. F

16、or dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication

17、 Year Title EN/HD Year IEC 61300-2-18 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-18: Tests - Dry heat - High temperature endurance EN 61300-2-18 - IEC 61300-2-19 - Fibre optic interconnecting devices and passive components - Basic te

18、st and measurement procedures - Part 2-19: Tests - Damp heat (steady state) EN 61300-2-19 - IEC 61300-2-22 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-22: Tests - Change of temperature EN 61300-2-22 - IEC 61753-1 - Fibre optic interco

19、nnecting devices and passive components performance standard - Part 1: General and guidance for performance standards EN 61753-1 - BS EN 62496-3:2011 2 62496-3 IEC:2011 CONTENTS INTRODUCTION 5 1 Scop e 6 2 Normative references 6 3 Terms and definitions 6 4 Preparation of a performance standard . 7 4

20、.1 Gene ra l . 7 4.2 Product definition . 7 4.3 Tests 7 4.4 Details 8 4.5 Requirements 8 4.6 Sample size . 8 4.7 Groupings /sequences . 8 4.8 Pass/fail criteria . 8 4.9 Reference product definition 8 4.10 Performance standard test report . 8 Annex A (normative) Tests and severities for performance s

21、tandards 9 Bibliography . 11 Table A.1 General operating service environments and definitions 9 Table A.2 Category C Controlled environment (Flexible optical circuit boards using optical glass fibres) 9 Table A.3 Category C Controlled environment (Optical circuit boards using optical waveguides) 10

22、BS EN 62496-3:201162496-3 IEC:2011 5 INTRODUCTION Performance standards define standard electro-optical performance under a set of prescribed conditions and contain a series or a set of tests and measurements (which may or may not be grouped into a specific schedule) with clearly defined conditions,

23、 severities and pass/fail criteria. The tests are intended to be run as an initial design verification to prove the products ability to satisfy the requirements of a specific application, market sector or user group. The following clauses in this part of IEC 62496 contain those sets of performance c

24、riteria that have been standardized for international use. A product that has been shown to meet all the requirements of a performance standard may be declared as complying with that performance standard. Products from one manufacturer that are tested to a performance standard will operate together

25、within the bounds of the criteria set by the performance standard. There is however no guarantee that products from different suppliers having the same standard interface, which have been independently tested to a performance standard, will meet the same levels of optical performance when mated toge

26、ther as those supplied by one manufacturer. Compliance with a performance standard demonstrates that a product has passed a design verification test; it is not a guarantee of lifetime assured performance or reliability. Both service life tests and reliability testing must be the subject of a separat

27、e test schedule where the tests and severities selected are such that they are truly representative of the requirements of these test programmes. Consistency of manufacture should be maintained using a recognized quality assurance programme, while the reliability of the product should be evaluated u

28、sing the procedures recommended in IEC 62005 series and IEC 61751. When possible, tests and measurements should be selected from the IEC 61300 series. Where this is not possible, the required test method should be attached as an annex to the performance standard. BS EN 62496-3:2011 6 62496-3 IEC:201

29、1 OPTICAL CIRCUIT BOARDS Part 3: Performance standards General and guidance 1 Scope This part of IEC 62496 covers general information on optical circuit board performance standards. It defines those tests and severities which form the performance categories or general operating service environments

30、and identifies those tests which are considered to be product-specific. Test and severity details are given in Annex A. IEC 62496-3 provides references, definitions and rules for creating optical circuit board performance standards, as well as related information pertinent to the subject. Subsequent

31、 parts of the IEC 62496-3 series are sequentially numbered and contain performance criteria for specific applications. Each part will be added as the performance criteria become standardized for international use. 2 Normative references The following referenced documents are indispensable for the ap

32、plication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-2-18, Fibre optic interconnecting devices and passive components Basic test and measurement procedures

33、 Part 2-18: Tests Dry heat High temperature endurance IEC 61300-2-19, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-19: Tests Damp heat (steady state) IEC 61300-2-22, Fibre optic interconnecting devices and passive components Basic test and m

34、easurement procedures Part 2-22: Tests Change of temperature IEC 61753-1, Fibre optic interconnecting devices and passive components performance standard Part 1: General and guidance for performance standards 3 Terms and definitions For the purposes of this document, the following terms and definiti

35、ons apply. 3 . 1 operating/service environment typical service environment or operating location simulated by a performance category 3 . 2 performance category series of tests and measurements (which may or may not be grouped into a specific sequence) with clearly stated conditions and severities, w

36、hich are chosen to simulate a particular operating service environment BS EN 62496-3:201162496-3 IEC:2011 7 3 . 3 performance standard standard designed to verify a product which is capable of meeting the requirements of a particular service environment NOTE It contains a combination of those tests,

37、 together with their severities and pass-fail criteria, which shall be applied to all optical circuit boards for a particular performance category, together with those which are considered specific to that particular product in that environment. 3 . 4 product specific tests those tests which are con

38、sidered to be specific to a particular product type, e.g. flexible optical circuit boards, rigid optical circuit board, optical fibre circuit boards, or waveguide circuit boards NOTE Where there is a specific IP (International Protection, IEC 60529) for a product, this shall be the subject of a sepa

39、rate test and shall be included in the relevant product performance standard. 3 . 5 performance standard test report report to be produced on completion of testing to a performance standard 4 Preparation of a performance standard 4.1 General In the preparation of a performance standard, the followin

40、g items shall be considered and instructions pertaining to them included: product definition, tests, details, requirements, sample size, groupings/sequences, pass/fail criteria, reference product definition. 4.2 Product definition The product to which the performance standard relates shall be clearl

41、y defined. 4.3 Tests The tests to be carried out on the product in order for it to meet the performance standard shall be clearly defined. No ambiguity or options shall be allowed. The tests selected, combined with the severities/durations, groupings/sequencing, method used and pass/fail criteria, s

42、hould be indicative of a defined product location within a service environment. The test method to be used shall be clearly defined for each test. Wherever possible the test method shall be selected from IEC referenced tests; where this is not possible other test methods may be defined. If a previou

43、sly undefined test method is used, the test method and details to be specified shall be included in an annex of the performance standard. BS EN 62496-3:2011 8 62496-3 IEC:2011 4.4 Details Severities, durations and the details to be considered shall be given for all tests and measurements presented i

44、n a performance standard. These shall be directly related to the requirements specified for a product location within a service environment to which the performance standard is intended to correspond. No ambiguity or options shall be allowed. 4.5 Requirements The performance requirements that shall

45、be satisfied in order for the product to comply with the standard shall be specified for each test and/or measurement. No ambiguities shall be allowed. 4.6 Sample size The sample size for each test shall be defined in an annex of the performance standard. No deviations shall be allowed. 4.7 Grouping

46、s/sequences Test groups and test sequences shall be defined in an annex as required by the user, user group or manufacturer. The number of samples for each test group shall also be defined in the annex. Where prohibitive cost is associated with the active devices, numbers of samples may be reduced.

47、4.8 Pass/fail criteria The pass/fail criteria shall be unambiguously stated for each test within the performance standard. No deviation or exceptions shall be allowed. 4.9 Reference product definition Where a reference product is called for in any of the test and measurement methods used within a pe

48、rformance standard, the reference product shall be clearly defined in an annex of the performance standard. 4.10 Performance standard test report Conformance with a performance standard shall be supported by a test report. The test report may be prepared by an independent test laboratory. The test r

49、eport shall clearly demonstrate that the tests were carried out as per the requirements of the performance standard and provide full details of the tests, together with a pass/fail declaration. Any product failing a particular test or sequence of tests shall be reported in the performance standard test report. The cause of the failure shall be given and any corrective action taken shall be described. If no design changes are made to the product, the test or test