EN 62604-1-2015 en Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality - Part 1 Generic specification.pdf

1、BSI Standards PublicationSurface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed qualityPart 1: Generic specificationBS EN 62604-1:2015National forewordThis British Standard is the UK implementation of EN 62604-1:2015. It isidentical to IEC 62604-1:2015.The UK participation in

2、 its preparation was entrusted to TechnicalCommittee EPL/49, Piezoelectric devices for frequency control and selection.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contra

3、ct. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 76518 6ICS 31.140Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

4、 of theStandards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62604-1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62604-1 September 2015 ICS 31.140 English Version Surface acoustic wave (SAW) and

5、 bulk acoustic wave (BAW) duplexers of assessed quality - Part 1: Generic specification (IEC 62604-1:2015) Duplexeurs ondes acoustiques de surface (OAS) et ondes acoustiques de volume (OAV) sous assurance de la qualit - Partie 1: Spcification gnrique (IEC 62604-1:2015) Oberflchenwellen-(OFW-) und Vo

6、lumenwellen-(BAW-) Duplexer mit bewerteter Qualitt - Teil 1: Fachgrundspezifikation (IEC 62604-1:2015) This European Standard was approved by CENELEC on 2015-08-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European S

7、tandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions

8、(English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committe

9、es of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov

10、enia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All

11、rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 62604-1:2015 E BS EN 62604-1:2015EN 62604-1:2015 2 European foreword The text of document 49/1143/FDIS, future edition 1 of IEC 62604-1, prepared by IEC/TC 49 “Piezoelectric, dielectric and electr

12、ostatic devices and associated materials for frequency control, selection and detection“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62604-1:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication

13、of an identical national standard or by endorsement (dop) 2016-05-20 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-08-20 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. C

14、ENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62604-1:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following

15、notes have to be added for the standards indicated: IEC 60068-2-10:2005 NOTE Harmonized as EN 60068-2-10:2005 (not modified). IEC 60862-1:2003 NOTE Harmonized as EN 60862-1:2003 (not modified). IEC 60862-2:2012 NOTE Harmonized as EN 60862-2:2012 (not modified). IEC 61019-1:2004 NOTE Harmonized as EN

16、 61019-1:2005 (not modified). IEC 62047-7:2011 NOTE Harmonized as EN 62047-7:2011 (not modified). IEC 62604-2:2011 NOTE Harmonized as EN 62604-2:2012 (not modified). BS EN 62604-1:2015EN 62604-1:2015 3 Annex ZA (normative) Normative references to international publications with their corresponding E

17、uropean publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

18、nts) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Ti

19、tle EN/HD Year IEC 60027 series Letter symbols to be used in electrical technology - - IEC 60050 series International Electrotechnical Vocabulary - - IEC 60068-1 2013 Environmental testing - Part 1: General and guidance EN 60068-1 2014 IEC 60068-2-1 - Environmental testing - Part 2-1: Tests - Test A

20、: Cold EN 60068-2-1 - IEC 60068-2-2 - Environmental testing - Part 2-2: Tests - Test B: Dry heat EN 60068-2-2 - IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) EN 60068-2-6 - IEC 60068-2-7 - Basic environmental testing procedures - Part 2-7: Tests - Test Ga

21、and guidance: Acceleration, steady state EN 60068-2-7 - IEC 60068-2-13 - Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure EN 60068-2-13 - IEC 60068-2-14 - Environmental testing - Part 2-14: Tests - Test N: Change of temperature EN 60068-2-14 - IEC 60068-2-17 1994

22、Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing EN 60068-2-17 1994 IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock EN 60068-2-27 - IEC 60068-2-30 - Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h c

23、ycle) EN 60068-2-30 - BS EN 62604-1:2015EN 62604-1:2015 4 Publication Year Title EN/HD Year IEC 60068-2-31 - Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens EN 60068-2-31 - IEC 60068-2-45 - Basic environmental testing procedures - Par

24、t 2-45: Tests - Test XA and guidance: Immersion in cleaning solvents EN 60068-2-45 - IEC 60068-2-52 - Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) EN 60068-2-52 - IEC 60068-2-58 - Environmental testing - Part 2-58: Tests - Test Td: Test methods for

25、 solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) EN 60068-2-58 - IEC 60068-2-64 - Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance EN 60068-2-64 - IEC 60068-2-78 - Environmental testing - Pa

26、rt 2-78: Tests - Test Cab: Damp heat, steady state EN 60068-2-78 - IEC 60122-1 - Quartz crystal units of assessed quality - Part 1: Generic specification EN 60122-1 - IEC 60617-DB - Graphical symbols for diagrams - - IEC 60642 - Piezoelectric ceramic resonators and resonator units for frequency cont

27、rol and selection - Chapter I: Standard values and conditions - Chapter II: Measuring and test conditions - - IEC 60695-11-5 - Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance EN 60695-11-5 - IEC 60749-28 - 1)Semiconducto

28、r devices - Mechanical and climatic test methods - Part 28: Electrostatic Discharge (ESD) Sensitivity Testing Direct contact charged device model (DC-CDM) FprEN 60749-28 - 1)IEC 61000-4-2 - Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge i

29、mmunity test EN 61000-4-2 - IEC 61340-3-1 - Electrostatics - Part 3-1: Methods for simulation of electrostatic effects - Human body model (HBM) electrostatic discharge test waveforms EN 61340-3-1 - 1) At draft stage. BS EN 62604-1:2015EN 62604-1:2015 5 Publication Year Title EN/HD Year IEC 61340-3-2

30、 - Electrostatics - Part 3-2: Methods for simulation of electrostatic effects - Machine model (MM) electrostatic discharge test waveforms EN 61340-3-2 - IEC 62761 - Guidelines for the measurement method of nonlinearity for surface acoustic wave (SAW) and bulk acoustic wave (BAW) devices in radio fre

31、quency (RF) EN 62761 - IEC 80000 series Quantities and units EN 80000 series ISO 80000 series Quantities and units - EN ISO 80000 series BS EN 62604-1:2015 2 IEC 62604-1:2015 IEC 2015 CONTENTS FOREWORD . 5 1 Scope 7 2 Normative references 7 3 Terms, definitions, units and symbols 8 3.1 Terms and def

32、initions 8 3.1.1 General terms 9 3.1.2 Response characteristics related terms . 10 3.1.3 SAW and BAW duplexers related terms . 14 3.2 Units and graphical symbols . 16 4 Order of precedence of documents 16 5 Preferred values for ratings and characteristics . 16 5.1 General . 16 5.2 Nominal frequency

33、bands 16 5.3 Operating temperature ranges, in degrees Celsius (C) 16 5.4 Climatic category 17 5.5 Bump severity . 17 5.6 Vibration severity 17 5.7 Shock severity 18 5.8 Fine leak rate 18 6 Marking . 18 6.1 Duplexer marking 18 6.2 Package marking 18 7 Quality assessment procedures . 19 7.1 General .

34、19 7.2 Primary stage of manufacture . 19 7.3 Structurally similar components 19 7.4 Subcontracting 19 7.5 Incorporated components 19 7.6 Manufacturers approval 19 7.7 Approval procedures . 19 7.7.1 General . 19 7.7.2 Capability approval 19 7.7.3 Qualification approval 20 7.8 Procedures for capabilit

35、y approval 20 7.8.1 General . 20 7.8.2 Eligibility for capability approval . 20 7.8.3 Application for capability approval . 20 7.8.4 Granting of capability approval 20 7.8.5 Capability manual 20 7.9 Procedures for qualification approval 20 7.9.1 General . 20 7.9.2 Eligibility for qualification appro

36、val . 20 7.9.3 Application for qualification approval . 21 7.9.4 Granting of qualification approval 21 7.9.5 Quality conformance inspection . 21 7.10 Test procedures 21 BS EN 62604-1:2015IEC 62604-1:2015 IEC 2015 3 7.11 Screening requirements 21 7.12 Rework and repair work 21 7.12.1 Rework 21 7.12.2

37、 Repair work . 21 7.13 Certified records of released lots 21 7.14 Validity of release . 21 7.15 Release for delivery 21 7.16 Unchecked parameters . 21 8 Test and measurement procedures 22 8.1 General . 22 8.2 Test and measurement conditions . 22 8.2.1 Standard conditions for testing 22 8.2.2 Precisi

38、on of measurement . 22 8.2.3 Precautions . 22 8.2.4 Alternative test methods 23 8.3 Visual inspection . 23 8.3.1 General . 23 8.3.2 Visual test A 23 8.3.3 Visual test B 23 8.4 Dimensions test 23 8.5 Electrical test procedures 23 8.5.1 S parameters measurement . 23 8.5.2 Intermodulation distortion me

39、asurement 25 8.5.3 Insulation resistance 25 8.5.4 Voltage proof . 25 8.6 Mechanical and environmental test procedures . 25 8.6.1 Sealing tests (non-destructive) 25 8.6.2 Soldering (solderability and resistance to soldering heat) (destructive) 26 8.6.3 Rapid change of temperature: severe shock by liq

40、uid immersion (non-destructive) 26 8.6.4 Rapid change of temperature with prescribed time of transition (non-destructive) 26 8.6.5 Bump (destructive) 26 8.6.6 Vibration (destructive) 27 8.6.7 Shock (destructive) 27 8.6.8 Free fall (destructive) . 27 8.6.9 Acceleration, steady state (non-destructive)

41、 28 8.6.10 Low air pressure (non-destructive) . 28 8.6.11 Dry heat (non-destructive) . 28 8.6.12 Damp heat, cyclic (destructive) 28 8.6.13 Cold (non-destructive) . 28 8.6.14 Climatic sequence (destructive) . 28 8.6.15 Damp heat, steady state (destructive) 29 8.6.16 Salt mist cyclic (destructive) 29

42、8.6.17 Immersion in cleaning solvents (non-destructive) . 29 8.6.18 Flammability test (destructive) . 29 8.6.19 Electrostatic discharge (ESD) sensitivity test (destructive) . 29 8.7 Endurance test procedure . 30 Bibliography 31 BS EN 62604-1:2015 4 IEC 62604-1:2015 IEC 2015 Figure 1 FBAR configurati

43、on 9 Figure 2 SMR configuration 10 Figure 3 Frequency response of SAW and BAW duplexers 15 Figure 4 S parameters measurement 24 Table 1 Frequency allocation of typical UMTS bands . 16 BS EN 62604-1:2015IEC 62604-1:2015 IEC 2015 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SURFACE ACOUSTIC WAVE (SAW

44、) AND BULK ACOUSTIC WAVE (BAW) DUPLEXERS OF ASSESSED QUALITY Part 1: Generic specification FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC

45、is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) a

46、nd Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with th

47、e IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly

48、 as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that s

49、ense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and