EN IEC 60051-5-2018 en Direct acting indicating analogue electrical measuring instruments and their accessories - Part 5 Special requirements for phase meters power factor meters a.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Direct acting indicating analogue electrical measuring instruments and their accessoriesPart 5: Special requirements for phase meters, power factor meters and synchroscopes (IEC 60051-5:2017)BS EN IEC 60051-5:2018EUROPE

2、AN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 60051-5 March 2018 ICS 17.220.20 Supersedes EN 60051-5:1989 English Version Direct acting indicating analogue electrical measuring instruments and their accessories - Part 5: Special requirements for phase meters, power factor meters and synchroscop

3、es (IEC 60051-5:2017) Appareils mesureurs lectriques indicateurs analogiques action directe et leurs accessoires - Partie 5: Exigences particulires pour les phasemtres, les appareils de mesure de facteur de puissance et les synchronoscopes (IEC 60051-5:2017) Direkt wirkende anzeigende elektrische Me

4、gerte und ihr Zubehr - Megerte mit Skalenanzeige - Teil 5: Spezielle Anforderungen fr Phasenverschiebungswinkel-Megerte, Leitstungsfaktor- Megerte und Synchronoskope (IEC 60051-5:2017) This European Standard was approved by CENELEC on 2018-01-19. CENELEC members are bound to comply with the CEN/CENE

5、LEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre o

6、r to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

7、 the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux

8、embourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische

9、Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 60051-5:2018 E National forewordThis British Standard is the UK implementation of EN IEC 600515:20

10、18. It is identical to IEC 600515:2017. It supersedes BS 895:1990, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PEL/85, Measuring equipment for electrical and electromagnetic quantities.A list of organizations represented on this committee can be ob

11、tained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 93061 4ICS 17.220.20Compliance w

12、ith a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 600515:2018EUROPEAN S

13、TANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 60051-5 March 2018 ICS 17.220.20 Supersedes EN 60051-5:1989 English Version Direct acting indicating analogue electrical measuring instruments and their accessories - Part 5: Special requirements for phase meters, power factor meters and synchroscopes (

14、IEC 60051-5:2017) Appareils mesureurs lectriques indicateurs analogiques action directe et leurs accessoires - Partie 5: Exigences particulires pour les phasemtres, les appareils de mesure de facteur de puissance et les synchronoscopes (IEC 60051-5:2017) Direkt wirkende anzeigende elektrische Megert

15、e und ihr Zubehr - Megerte mit Skalenanzeige - Teil 5: Spezielle Anforderungen fr Phasenverschiebungswinkel-Megerte, Leitstungsfaktor- Megerte und Synchronoskope (IEC 60051-5:2017) This European Standard was approved by CENELEC on 2018-01-19. CENELEC members are bound to comply with the CEN/CENELEC

16、Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to

17、 any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

18、 official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembo

19、urg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Norm

20、ung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 60051-5:2018 E BS EN IEC 600515:2018EN IEC 60051-5:2018 (E) 2 European foreword The text of document 8

21、5/581/CDV, future edition 5 of IEC 60051-5, prepared by IEC/TC 85 “Measuring equipment for electrical and electromagnetic quantities“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60051-5:2018. The following dates are fixed: latest date by which the document has to

22、 be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-10-19 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-01-19 This document supersedes EN 60051-5:1989. Attention is drawn to the po

23、ssibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Assoc

24、iation, and supports essential requirements of EU Directives. For the relationship with EU Directives see informative Annex ZZ, which is an integral part of this document. Endorsement notice The text of the International Standard IEC 60051-5:2017 was approved by CENELEC as a European Standard withou

25、t any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 60051-91NOTE Harmonized as EN 60051-92. 1To be published. Stage at the time of publication: IEC CDV 60051-9:2018. 2To be published. Stage at the time of publication: prEN

26、 60051-9:2018. BS EN IEC 600515:2018EN IEC 60051-5:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes require

27、ments of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevan

28、t EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60051-1 2016 Direct acting indicating analogue electrical measuring instruments and their accessories Part 1:

29、Definitions and general requirements common to all parts EN 60051-1 2017 BS EN IEC 600515:2018This page deliberately left blank 2 IEC 60051-5:2017 IEC 2017 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms and definitions 7 4 Description, classification and compliance

30、 . 7 4.1 Description . 7 4.2 Classification 7 4.3 Compliance with the requirements of this standard . 7 5 Requirements 8 5.1 Reference conditions 8 5.2 Limits of intrinsic uncertainty, fiducial value 8 5.2.1 Limits of intrinsic uncertainty . 8 5.2.2 Correspondence between intrinsic uncertainty and a

31、ccuracy class 8 5.2.3 Fiducial value 8 5.3 Nominal range of use and variations . 8 5.3.1 Nominal range of use . 8 5.3.2 Limits of variations. 9 5.3.3 Conditions for the determination of variations 10 5.4 Operating uncertainty, overall system uncertainty and variations 10 5.5 Electrical requirements

32、. 10 5.5.1 Electrical safety requirements 10 5.5.2 Self-heating . 10 5.5.3 Permissible overloads 10 5.5.4 Limiting range of temperature 11 5.5.5 Deviation from zero . 11 5.5.6 Electromagnetic compatibility (EMC) . 11 5.5.7 Special requirements for synchroscopes 12 5.6 Constructional requirements . 1

33、2 5.6.1 General constructional requirements . 12 5.6.2 Damping 12 5.6.3 Sealing to prevent access 12 5.6.4 Scales . 12 5.6.5 Stopper 12 5.6.6 Preferred values 12 5.6.7 Adjusters, mechanical and/or electrical 13 5.6.8 Effects of vibration and shock 13 5.6.9 Degrees of protection provided by enclosure

34、 . 13 5.6.10 Terminals 13 6 Information, markings and symbols 13 6.1 Information . 13 6.2 Markings, symbols and their locations . 13 6.3 Markings relating to the reference values and nominal ranges of use of influence quantities . 13 6.4 The symbols for marking instruments and accessories 13 6.5 Mar

35、kings and symbols for terminals 13 2 IEC 60051-5:2017 IEC 2017 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms and definitions 7 4 Description, classification and compliance . 7 4.1 Description . 7 4.2 Classification 7 4.3 Compliance with the requirements of this st

36、andard . 7 5 Requirements 8 5.1 Reference conditions 8 5.2 Limits of intrinsic uncertainty, fiducial value 8 5.2.1 Limits of intrinsic uncertainty . 8 5.2.2 Correspondence between intrinsic uncertainty and accuracy class 8 5.2.3 Fiducial value 8 5.3 Nominal range of use and variations . 8 5.3.1 Nomi

37、nal range of use . 8 5.3.2 Limits of variations. 9 5.3.3 Conditions for the determination of variations 10 5.4 Operating uncertainty, overall system uncertainty and variations 10 5.5 Electrical requirements . 10 5.5.1 Electrical safety requirements 10 5.5.2 Self-heating . 10 5.5.3 Permissible overlo

38、ads 10 5.5.4 Limiting range of temperature 11 5.5.5 Deviation from zero . 11 5.5.6 Electromagnetic compatibility (EMC) . 11 5.5.7 Special requirements for synchroscopes 12 5.6 Constructional requirements . 12 5.6.1 General constructional requirements . 12 5.6.2 Damping 12 5.6.3 Sealing to prevent ac

39、cess 12 5.6.4 Scales . 12 5.6.5 Stopper 12 5.6.6 Preferred values 12 5.6.7 Adjusters, mechanical and/or electrical 13 5.6.8 Effects of vibration and shock 13 5.6.9 Degrees of protection provided by enclosure . 13 5.6.10 Terminals 13 6 Information, markings and symbols 13 6.1 Information . 13 6.2 Mar

40、kings, symbols and their locations . 13 6.3 Markings relating to the reference values and nominal ranges of use of influence quantities . 13 6.4 The symbols for marking instruments and accessories 13 6.5 Markings and symbols for terminals 13 BS EN IEC 600515:2018IEC 60051-5:2017 IEC 2017 3 6.5.1 Req

41、uirements for markings 13 6.5.2 Earthing (grounding) terminals . 13 6.5.3 Measuring circuit terminals 14 6.5.4 Special markings for terminals . 14 6.6 Instructions for use . 14 7 Package 14 8 Test rules 14 Annex A (normative) Nonconformity classification of tests . 15 Bibliography 16 Table 1 Referen

42、ce conditions and tolerances, additional to those given in Table 2 of IEC 60051-1:2016, for testing purposes relating to the influence quantities . 8 Table 2 Limits of the nominal range of use and permissible variations in addition to those given in Table 3 of IEC 60051-1:2016 9 Table 3 Overloads of

43、 short duration . 11 Table A.1 Nonconformity classification of tests 15 BS EN IEC 600515:2018 4 IEC 60051-5:2017 IEC 2017 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DIRECT ACTING INDICATING ANALOGUE ELECTRICAL MEASURING INSTRUMENTS AND THEIR ACCESSORIES Part 5: Special requirements for phase meters

44、, power factor meters and synchroscopes FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all que

45、stions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publicatio

46、n(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC col

47、laborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion

48、 on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensu

49、re that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be cl