EN IEC 61347-2-14-2018 en Lamp controlgear - Part 2-14 Particular requirements for DC and or AC supplied electronic controlgear for fluorescent induction lamps.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Lamp controlgearPart 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lampsBS EN IEC 61347-2-14:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61347-

2、2-14 April 2018 ICS 29.140.99 English Version Lamp controlgear - Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps (IEC 61347-2-14:2018) Appareillages de lampes - Partie 2-14: Exigences particulires pour les appareillages lectroniques

3、 aliments en courant continu et/ou alternatif pour les lampes fluorescentes induction (IEC 61347-2-14:2018) Gerte fr Lampen - Teil 2-14: Besondere Anforderungen an gleich- und/oder wechselstromversorgte elektronische Betriebsgerte fr Induktions-Leuchtstofflampen (IEC 61347-2-14:2018) This European S

4、tandard was approved by CENELEC on 2018-04-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

5、erning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC m

6、ember into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Repu

7、blic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Stand

8、ardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IE

9、C 61347-2-14:2018 E National forewordThis British Standard is the UK implementation of EN IEC 61347214:2018. It is identical to IEC 61347214:2018.The UK participation in its preparation was entrusted to Technical Committee CPL/34/3, Auxiliaries for lamps.A list of organizations represented on this c

10、ommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 94325 6ICS 29.

11、140.99Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 6134

12、7214:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61347-2-14 April 2018 ICS 29.140.99 English Version Lamp controlgear - Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps (IEC 61347-2-14:2018) Appareillages de lampes -

13、 Partie 2-14: Exigences particulires pour les appareillages lectroniques aliments en courant continu et/ou alternatif pour les lampes fluorescentes induction (IEC 61347-2-14:2018) Gerte fr Lampen - Teil 2-14: Besondere Anforderungen an gleich- und/oder wechselstromversorgte elektronische Betriebsger

14、te fr Induktions-Leuchtstofflampen (IEC 61347-2-14:2018) This European Standard was approved by CENELEC on 2018-04-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard with

15、out any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any ot

16、her language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyp

17、rus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turk

18、ey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form

19、 and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 61347-2-14:2018 E BS EN IEC 61347214:2018EN IEC 61347-2-14:2018 (E) 2 European foreword The text of document 34C/1374/FDIS, future edition 1 of IEC 61347-2-14, prepared by IEC/SC 34C: “Auxiliaries for lamps, of IEC technical c

20、ommittee 34: Lamps and related equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61347-2-14:2018. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by

21、endorsement (dop) 2019-01-03 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-04-03 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for

22、 identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61347-2-14:2018 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated:

23、 IEC 60598-2-22 NOTE Harmonized as EN 60598-2-22. BS EN IEC 61347214:2018EN IEC 61347-2-14:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or

24、all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifi

25、cations, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60929 2011 AC and/or DC-supplied electronic control gear for tubular f

26、luorescent lamps - Performance requirements EN 60929 2011 - - + AC 2011 IEC 61347-1 2015 Lamp controlgear - Part 1: General and safety requirement EN 61347-1 2015 + A1 2017 + A1 2018 IEC 61347-2-7 2011 Lamp controlgear - Part 2-7: Particular requirements for battery supplied electronic controlgear f

27、or emergency lighting (self-contained) EN 61347-2-7 2012 + A1 2017 - - IEC 61547 - Equipment for general lighting purposes - EMC immunity requirements EN 61547 - IEC 62532 2011 Fluorescent induction lamps - Safety specifications EN 62532 2011 IEC 62639 2012 Fluorescent induction lamps - Performance

28、specification EN 62639 2012 BS EN IEC 61347214:2018 2 IEC 61347-2-14:2018 IEC 2018 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms and definitions 7 4 General requirements 9 5 General notes on tests 9 6 Classification . 9 7 Marking . 9 7.1 General . 9 7.2 Mandatory

29、markings 9 7.3 Information to be provided, if applicable 10 8 Protection against accidental contact with live parts 10 9 Terminals 10 10 Provisions for earthing . 10 11 Moisture resistance and insulation . 10 12 Electric strength 10 13 Thermal endurance test for windings . 10 14 Fault conditions . 1

30、0 15 Protection of associated components. 11 15.1 Maximum peak voltage under normal operation conditions 11 15.2 Maximum working voltage under normal and abnormal operating conditions . 11 15.3 Compliance . 11 15.4 Insulation of input terminals of controllable electronic controlgear . 11 16 Abnormal

31、 conditions 12 16.1 Abnormal conditions for DC and/or AC supplied electronic controlgear . 12 16.2 Additional abnormal conditions for DC only electronic controlgear 12 17 Construction 12 18 Creepage distances and clearances 12 19 Screws, current-carrying parts and connections . 12 20 Resistance to h

32、eat, fire and tracking 13 21 Resistance to corrosion . 13 Annex A (normative) Test to establish whether a conductive part is a live part which may cause an electric shock . 14 Annex B (normative) Particular requirements for thermally protected lamp controlgear 15 Annex C (normative) Particular requi

33、rements for electronic lamp controlgear with means of protection against overheating . 16 Annex D (normative) Requirements for carrying out the heating tests of thermally protected lamp controlgear . 17 Annex E (normative) Use of constant S other than 4 500 in twtests . 18 Annex F (normative) Draugh

34、t-proof enclosure 19 Annex G (normative) Explanation of the derivation of the values of pulse voltages 20 Annex H (normative) Tests. 21 BS EN IEC 61347214:2018IEC 61347-2-14:2018 IEC 2018 3 Annex I (normative) Additional requirements for built-in magnetic ballast with double or reinforced insulation

35、 . 22 Annex J (normative) Particular additional safety requirements for DC and/or AC supplied electronic controlgear for emergency lighting 23 J.1 General . 23 J.2 Marking . 23 J.2.1 Mandatory markings 23 J.2.2 Information to be provided if applicable . 23 J.3 General statement 23 J.4 Starting condi

36、tions 24 J.5 Operating conditions . 24 J.6 Current . 24 J.7 EMC immunity. 24 J.8 Pulse voltage from central battery systems . 24 J.9 Tests for abnormal conditions . 24 J.10 Temperature cycling test and endurance test 25 J.11 Functional safety (EBLF) . 25 Annex K (informative) Conformity testing duri

37、ng manufacture 26 Annex L (normative) Particular additional requirements for controlgear providing SELV . 27 Annex M (informative) Dielectric strength test voltages for controlgear intended for the use in impulse withstand Category III 28 Annex N (normative) Requirements for insulation materials use

38、d for double or reinforced insulation . 29 Annex O (normative) Additional requirements for built-in electronic controlgear with double or reinforced insulation 30 Annex P (normative) Creepage distances and clearances and distance through insulation (DTI) for lamp controlgear which are protected agai

39、nst pollution by the use of coating or potting 31 Annex Q (informative) Example for Upcalculation . 32 Annex R (informative) Concept of creepage distances and clearances . 33 Annex S (informative) Examples of controlgear insulation coordination 34 Annex T (informative) Creepage distances and clearan

40、ces for controlgear with a higher degree of availability (impulse withstand category III) . 35 Bibliography 36 Table 1 Relation between RMS working voltage and maximum peak voltage . 11 Table J.1 Pulse voltages 24 BS EN IEC 61347214:2018 4 IEC 61347-2-14:2018 IEC 2018 INTERNATIONAL ELECTROTECHNICAL

41、COMMISSION _ LAMP CONTROLGEAR Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical c

42、ommittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Techn

43、ical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmen

44、tal and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or ag

45、reements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international us

46、e and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to prom

47、ote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indic

48、ated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6)

49、 All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publicatio