EN IEC 61730-2-2018 en Photovoltaic (PV) module safety qualification - Part 2 Requirements for testing.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Photovoltaic (PV) module safety qualificationPart 2: Requirements for testingBS EN IEC 617302:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61730-2 April 2018 ICS 27.160 Supersedes EN 61730-2:2007 English

2、 Version Photovoltaic (PV) module safety qualification - Part 2: Requirements for testing (IEC 61730-2:2016) Qualification pour la sret de fonctionnement des modules photovoltaques (PV) - Partie 2: Exigences pour les essais (IEC 61730-2:2016) Photovoltaik (PV) Module - Sicherheitsqualifikation - Tei

3、l 2: Anforderungen an die Prfung (IEC 61730-2:2016) This European Standard was approved by CENELEC on 2016-09-22. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without a

4、ny alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other l

5、anguage made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,

6、the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey an

7、d the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and

8、by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 61730-2:2018 E National forewordThis British Standard is the UK implementation of EN IEC 617302:2018. It is identical to IEC 617302:2016. It supersedes BS EN 617302:2007+A1:2012, which is withdrawn.The UK participation in its prepa

9、ration was entrusted to Technical Committee GEL/82, Photovoltaic Energy Systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its cor

10、rect application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 76453 0ICS 27.160Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strate

11、gy Committee on 31 May 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 617302:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61730-2 April 2018 ICS 27.160 Supersedes EN 61730-2:2007 English Version Photovoltaic (PV) module safety qualifica

12、tion - Part 2: Requirements for testing (IEC 61730-2:2016) Qualification pour la sret de fonctionnement des modules photovoltaques (PV) - Partie 2: Exigences pour les essais (IEC 61730-2:2016) Photovoltaik (PV) Module - Sicherheitsqualifikation - Teil 2: Anforderungen an die Prfung (IEC 61730-2:2016

13、) This European Standard was approved by CENELEC on 2016-09-22. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographica

14、l references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibili

15、ty of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, For

16、mer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Elect

17、rotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Member

18、s. Ref. No. EN IEC 61730-2:2018 E BS EN IEC 617302:2018EN IEC 61730-2:2018 (E) 2 European foreword The text of document 82/1129/FDIS, future edition 2 of IEC 61730-2, prepared by IEC/TC 82 “Solar photovoltaic energy systems“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as E

19、N IEC 61730-2:2018. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-10-27 latest date by which the national standards conflicting with the document have to be withdr

20、awn (dow) 2021-04-27 This document supersedes EN 61730-2:2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared un

21、der a mandate given to CENELEC by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For the relationship with EU Directive 2006/42/EC see informative Annex ZZ, which is an integral part of this document. Endorsement notice The te

22、xt of the International Standard IEC 61730-2:2016 was approved by CENELEC as a European Standard without any modification. BS EN IEC 617302:2018EN IEC 61730-2:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The followi

23、ng documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 W

24、here an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60

25、060-1 - High-voltage test techniques - Part 1: General definitions and test requirements EN 60060-1 2010 IEC 60068-2-1 - Environmental testing - Part 2-1: Tests - Test A: Cold EN 60068-2-1 2007 IEC 60068-2-2 - Environmental testing - Part 2-2: Tests - Test B: Dry heat EN 60068-2-2 2007 IEC 60068-3-5

26、 - Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers EN 60068-3-5 2002 IEC 60598-1 (mod) 2014 Luminaires - Part 1: General requirements and tests EN 60598-1 2015 IEC 60664-1 2007 Insulation coordination for equipment wit

27、hin low-voltage systems - Part 1: Principles, requirements and tests EN 60664-1 2007 IEC 60695-2-10 - Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure EN 60695-2-10 2002 IEC 60904-2 - Photovoltaic devices - Part 2: Requirements for

28、photovoltaic reference devices EN 60904-2 2015 IEC 60904-9 - Photovoltaic devices - Part 9: Solar simulator performance requirements EN 60904-9 2007 IEC 60950-1 (mod) 2005 Information technology equipment - Safety - Part 1: General requirements EN 60950-1 2006 - - + A11 2009 - - + A12 2011 - - + AC

29、2011 IEC 61010-1 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 1: General requirements EN 61010-1 2010 IEC 61032 1997 Protection of persons and equipment by enclosures - Probes for verification EN 61032 1998 IEC 61140 - Protection against electric

30、shock - Common aspects for installation and equipment EN 61140 2016 IEC 61215 series Terrestrial photovoltaic (PV) modules Design qualification and type approval EN 61215 series IEC 61215-2 - Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures EN

31、61215-2 2017 BS EN IEC 617302:2018EN IEC 61730-2:2018 (E) 4 IEC 61730-1 2016 Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction EN 61730-1 2018 IEC 62790 - Junction boxes for photovoltaic modules - Safety requirements and tests EN 62790 2015 ISO 813 2016 Rubber, vu

32、lcanized or thermoplastic_- Determination of adhesion to a rigid substrate - 90 peel method - - ISO 4046-4 2016 Paper, board, pulps and related terms - Vocabulary - Part 4: Paper and board grades and converted products - - ISO 4587 2003 Adhesives - Determination of tensile lap-shear strength of rigi

33、d-to-rigid bonded assemblies - - ISO 5893 2002 Rubber and plastics test equipment - Tensile, flexural and compression types (constant rate of traverse) - Specification - - ISO 8124-1 2018 Safety of toys - Part 1: Safety aspects related to mechanical and physical properties - - ISO 11925-2 2010 React

34、ion to fire tests - Ignitability of products subjected to direct impingement of flame - Part 2: Single-flame source test EN ISO 11925-2 2010 ISO 23529 2016 Rubber - General procedures for preparing and conditioning test pieces for physical test methods - - ISO/IEC 17025 - General requirements for th

35、e competence of testing and calibration laboratories EN ISO/IEC 17025 2017 ANSI Z97.1 2009 American National Standard for Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test - - ANSI/UL 1703 2015 Flat-Plate Photovoltaic Modules and Panels - - BS EN IEC

36、617302:2018EN IEC 61730-2:2018 (E) 5 Annex ZZ (informative) Relationship between this European standard and the safety objectives of Directive 2014/35/EU 2014 OJ L96 aimed to be covered This European Standard has been prepared under a Commissions standardization request relating to harmonized standa

37、rds in the field of the Low Voltage Directive, M/511, to provide one voluntary means of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the making available on

38、the market of electrical equipment designed for use within certain voltage limits 2014 OJ L96. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of the

39、scope of this standard, a presumption of conformity with the corresponding safety objectives of that Directive, and associated EFTA regulations. Table ZZ.1 Correspondence between this European standard and Annex I of Directive 2014/35/EU 2014 OJ L96 Safety objectives of Directive 2014/35/EU Clause(s

40、) / sub-clause(s) of this EN Remarks / Notes 1. General conditions 1 (a) the essential characteristics, the recognition and observance of which will ensure that electrical equipment will be used safely and in applications for which it was made, shall be marked on the electrical equipment, or, if thi

41、s is not possible, on an accompanying document; EN 61730-1, 5.2 1 (b) the electrical equipment, together with its component parts, shall be made in such a way as to ensure that it can be safely and properly assembled and connected; EN 61730-1, 5.2 1(c) the electrical equipment shall be so designed a

42、nd manufactured as to ensure that protection against the hazards set out in points 2 and 3 is assured, providing that the equipment is used in applications for which it was made and is adequately maintained. EN 61730-1, 5.2 refer to 2a) to 2d) and 3a) to 3c) of this table cl. 5.4 (intended use) BS E

43、N IEC 617302:2018EN IEC 61730-2:2018 (E) 6 Safety objectives of Directive 2014/35/EU Clause(s) / sub-clause(s) of this EN Remarks / Notes 2. Protection against hazards arising from the electrical equipment Measures of a technical nature shall be laid down in accordance with point 1, in order to ensu

44、re that: 2 (a) persons and domestic animals are adequately protected against the danger of physical injury or other harm which might be caused by direct or indirect contact; EN 61730-1, 5.2.2, 5.3.4, 5.3.5, 5.5.4, 5.6.4.2 EN 61730-2, 4.4 EN 61730-2, 10.9, (MST 11) EN 61730-2, 10.11, (MST 13) EN 6173

45、0-2, 10.12, (MST 14) EN 61730-2, 10.13, (MST 16) EN 61730-2, 10.14, (MST 17) 2 (b) temperatures, arcs or radiation which would cause a danger, are not produced; EN 61730-1, 5.1, 5.2.2.1, 5.2.3, 5.3, 5.5 and Annex B (B6) EN 61730-2, 4.2 EN 61730-2, 10.15, (MST 21) 2 (c) persons, domestic animals and

46、property are adequately protected against non-electrical dangers caused by the electrical equipment which are revealed by experience; EN 61730-1, 5.2.3 EN 61730-2, 10.7, (MST 06) EN 61730-2, 10.10, (MST 12) EN 61730-2, 10.21, (MST 32) EN 61730-2, 10.23, (MST 34) 2 (d) the insulation is suitable for

47、foreseeable conditions. EN 61730-1, 5.2.2.1 k) and MST 26 EN 61730-1, 5.2.2, 5.2.2.1, 5.3.4, 5.3.5, 5.5.4, 5.6 and 5.6.4.2 EN 61730-2, 4.4 EN 61730-2, 10.13, (MST 16) EN 61730-2, 10.14, (MST 17) BS EN IEC 617302:2018EN IEC 61730-2:2018 (E) 7 Safety objectives of Directive 2014/35/EU Clause(s) / sub-

48、clause(s) of this EN Remarks / Notes 3. Protection against hazards which may be caused by external influences on the electrical equipment Technical measures shall be laid down in accordance with point 1, in order to ensure that the electrical equipment: 3 (a) meets the expected mechanical requiremen

49、ts in such a way that persons, domestic animals and property are not endangered; EN 61730-1, 5.1, 5.2.3, 5.3, 5.4 and 5.5 EN 61730-2, 4.2 EN 61730-2, 10.7, (MST 06) EN 61730-2, 10.21, (MST 32) EN 61730-2, 10.23, (MST 34) 3 (b) is resistant to non-mechanical influences in expected environmental conditions, in such a way that persons, domestic animals and property are not endangered; EN 61730-2, 4.5 EN 61730-2, 10.15, (MST 21) EN 61730-2, 10.17, (MST 23) No remote access to modules to influence function. There a