EN IEC 63093-7-2018 en Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7 EER-cores.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Ferrite cores - Guidelines on dimensions and the limits of surface irregularitiesPart 7: EER-coresBS EN IEC 63093-7:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 63093-7 May 2018 ICS 29.100.10 English Ver

2、sion Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7: EER-cores (IEC 63093-7:2018) Noyaux de ferrite - Lignes directrices concernant les dimensions et les limites des irrgularits de surface - Partie 7 : Noyaux EER (IEC 63093-7:2018) Ferritkerne - Richtlinie

3、n zu Maen und Grenzen von Oberflchenbeschdigungen - Teil 7: EER-Kerne (IEC 63093-7:2018) This European Standard was approved by CENELEC on 2018-04-26. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st

4、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, Fren

5、ch, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria,

6、 Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia,

7、Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All ri

8、ghts of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 63093-7:2018 E National forewordThis British Standard is the UK implementation of EN IEC 630937:2018. It is identical to IEC 630937:2018.The UK participation in its preparation was entrusted to

9、Technical Committee EPL/51, Transformers, inductors, magnetic components and ferrite materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsi

10、ble for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96673 6ICS 29.100.10Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards

11、 Policy and Strategy Committee on 31 May 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 630937:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 63093-7 May 2018 ICS 29.100.10 English Version Ferrite cores - Guidelines on dimensions and the

12、limits of surface irregularities - Part 7: EER-cores (IEC 63093-7:2018) Noyaux de ferrite - Lignes directrices concernant les dimensions et les limites des irrgularits de surface - Partie 7 : Noyaux EER (IEC 63093-7:2018) Ferritkerne - Richtlinien zu Maen und Grenzen von Oberflchenbeschdigungen - Te

13、il 7: EER-Kerne (IEC 63093-7:2018) This European Standard was approved by CENELEC on 2018-04-26. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up

14、-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by t

15、ranslation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republi

16、c, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United King

17、dom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means rese

18、rved worldwide for CENELEC Members. Ref. No. EN IEC 63093-7:2018 E BS EN IEC 630937:2018EN IEC 63093-7:2018 (E) 2 European foreword The text of document 51/1217/FDIS, future edition 1 of IEC 63093-7, prepared by IEC/TC 51 “Magnetic components, ferrite and magnetic powder materials“ was submitted to

19、the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 63093-7:2018. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-01-26 latest date by which the national

20、 standards conflicting with the document have to be withdrawn (dow) 2021-04-26 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice

21、 The text of the International Standard IEC 63093-7:2018 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated : IEC 60424-3:2015 NOTE Harmonized as EN 60424-3:2016 (not modifi

22、ed). BS EN IEC 630937:2018EN IEC 63093-7:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of t

23、his document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD ap

24、plies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60205 - Calculation of the effective parameters of magnetic piece parts EN 60205 - IEC 60401-1 - Terms and nomenclature

25、for cores made of magnetically soft ferrites - Part 1: Terms used for physical irregularities EN 60401-1 - IEC 60424-1 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 1: General Specification EN 60424-1 - BS EN IEC 630937:2018 2 IEC 63093-7:2018 IEC 2018 CONTENTS FOREWORD

26、 . 4 1 Scope 6 2 Normative references 6 3 Terms and definitions 6 4 Primary dimensions . 6 4.1 General . 6 4.2 Dimensions of EER-cores . 7 4.2.1 Principal dimensions 7 4.2.2 Effective parameter and Aminvalues . 8 4.3 Dimensional limits for coil formers. 8 5 Limits of surface irregularities 9 5.1 Gen

27、eral . 9 5.2 Chips and ragged edges . 10 5.2.1 General 10 5.2.2 Chips and ragged edges on the mating surfaces (see Figure 4) . 10 5.2.3 Chips and ragged edges on the other surfaces (see Figure 4) . 10 5.3 Cracks 12 5.4 Flash 12 5.5 Pull-outs . 12 5.6 Crystallites 13 5.7 Pores 14 Annex A (normative)

28、Derived standards . 15 Annex B (normative) Example of dimensions for gauges to check the dimensions of EER-cores meeting this primary standard . 16 B.1 General . 16 B.2 Procedure and requirements . 16 Annex C (informative) Examples of allowable areas of chips 17 Bibliography 18 Figure 1 Dimensions o

29、f EER-cores 7 Figure 2 Essential dimensions of coil formers 8 Figure 3 Examples of surface irregularities 9 Figure 4 Chip locations for EER-cores . 10 Figure 5 Cracks and pull-out locations for EER-cores 12 Figure 6 Crystallite location for EER-cores . 13 Figure 7 Pore location for EER-cores . 14 Fi

30、gure B.1 Gauge dimensions 16 Table 1 Dimensions of EER-cores 7 Table 2 Effective parameter values of EER-cores 8 BS EN IEC 630937:2018IEC 63093-7:2018 IEC 2018 3 Table 3 Dimensional limits for coil formers . 9 Table 4 Area and length reference for visual inspection . 11 Table 5 Limits for cracks 13

31、Table B.1 Gauge dimensions . 16 Table C.1 Allowable areas of chips for EER-cores . 17 BS EN IEC 630937:2018 4 IEC 63093-7:2018 IEC 2018 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FERRITE CORES GUIDELINES ON DIMENSIONS AND THE LIMITS OF SURFACE IRREGULARITIES Part 7: EER-cores FOREWORD 1) The Intern

32、ational Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electr

33、onic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees

34、; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Stan

35、dardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has r

36、epresentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate,

37、 IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional pu

38、blications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some a

39、reas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents incl

40、uding individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reli

41、ance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the e

42、lements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 63093-7 has been prepared by IEC technical committee 51: Magnetic components, ferrite and magnetic powder materials. This f

43、irst edition cancels and replaces the first edition of IEC 62317-7 published in 2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 62317-7: a) IEC 63093-7 integrates IEC 62317-7 and IEC 60424-3; b) IEC 60424-3:20

44、15, Table 2, has been included in Annex C as Table C.1. BS EN IEC 630937:2018IEC 63093-7:2018 IEC 2018 5 The text of this International Standard is based on the following documents: FDIS Report on voting 51/1217/FDIS 51/1226/RVD Full information on the voting for the approval of this International S

45、tandard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 63093 series, published under the general title Ferrite cores Guidelines on dimensions and the limits of surface

46、 irregularities can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be rec

47、onfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. BS EN IEC 630937:2018 6 IEC 63093-7:2018 IEC 2018 FERRITE CORES GUIDELINES ON DIMENSIONS AND THE LIMITS OF SURFACE IRREGULARITIES Part 7: EER-cores 1 Scope This part

48、 of IEC 63093 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EER-cores made of ferrite, the essential dimensions of coil formers to be used with them as well the effective parameter values to be used in calculations involving them, and give

49、s guidelines on allowable limits of surface irregularities applicable to EER-cores. This document is a specification useful in the negotiations between ferrite core manufacturers and customers about surface irregularities. The use of “derived” standards which give more detailed specifications of component parts while still permitting compliance with this document is discussed in Annex A. 2 Normative references The following documents are referred to in