EN ISO 1119-2011 en Geometrical product specifications (GPS) - Series of conical tapers and taper angles《产品几何量规范(GPS) 锥度和锥度角系列》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 1119:2011Geometrical product specifications (GPS) Series of conical tapers and taper angles (ISO 1119:2011)BS EN ISO 1119:2011 BRITISH STANDARDNational forewordThis Bri

2、tish Standard is the UK implementation of EN ISO 1119:2011. It supersedes BS EN ISO 1119:2002, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this committee can be obtained on

3、 request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 69104 1 ICS 17.040.01 Compliance with a British Standard cannot confer immunity from legal obligations.This Br

4、itish Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1119 December 2011 ICS 17.040.01 Supersedes EN ISO 1119:2002English Version

5、 Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011) Spcification gomtrique des produits (GPS) - Srie dangles de cnes et de conicits (ISO 1119:2011) Geometrische Produktspezifikation (GPS) - Reihen von Regeln und Kegelwinkeln (ISO 1119:2011) This Euro

6、pean Standard was approved by CEN on 14 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

7、concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN membe

8、r into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

9、Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marn

10、ix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1119:2011: EBS EN ISO 1119:2011 EN ISO 1119:2011 (E) 3 Foreword This document (EN ISO 1119:2011) has been prepared by Technical Committee ISO/TC 213 “D

11、imensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national stan

12、dard, either by publication of an identical text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN

13、and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1119:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Aus

14、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

15、 Endorsement notice The text of ISO 1119:2011 has been approved by CEN as a EN ISO 1119:2011 without any modification. BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction . v 1 Scope 1 2 Normative references 1 3 Terms and definitions . 1 4 Value

16、s . 1 Annex A (informative) Relation to the GPS matrix model . 5 Bibliography 7 BS EN ISO 1119:2011ISO 1119:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of

17、 preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental

18、, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main

19、task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Atten

20、tion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1119 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specification

21、s and verification. This third edition cancels and replaces the second edition (ISO 1119:1998); the tables have been corrected and updated, but not technically modified. BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved vIntroduction This International Standard is a geometrical produc

22、t specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain links 1 and 2 of the chain of standards on angle. The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamen

23、tal rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document, unless otherwise indicated For more detailed information of the relation of this International Standard to other standards

24、and the GPS matrix model, see Annex A. BS EN ISO 1119:2011BS EN ISO 1119:2011INTERNATIONAL STANDARD ISO 1119:2011(E) ISO 2011 All rights reserved 1Geometrical product specifications (GPS) Series of conical tapers and taper angles 1 Scope This International Standard provides calculated values for a s

25、eries of cones or conical tapers, ranging from 120 to less than 1, or ratios from 1:0,289 to 1:500, intended for general use in technical engineering. It applies only to plain conical surfaces, and excludes prismatic pieces, taper threads, bevel gears, etc. 2 Normative references The following refer

26、enced document is indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3040, Geometrical product specifications (GPS) Dimensioning and to

27、lerancing Cones 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 3040 apply. 4 Values Series 1 and 2 initial values, as specified in Table 1, should be used in the order of preference given with the purpose of reducing the range of tools, gauges and m

28、easuring instruments required for production of conical parts. Table 2 shall be used only for the particular applications indicated in the last column. For information, these tables give calculated values for the cone angle or the rate of taper, in order to facilitate design, production and control

29、of conical pieces. Cones shall be dimensioned and toleranced according to ISO 3040. BS EN ISO 1119:2011ISO 1119:2011(E) 2 ISO 2011 All rights reservedTable 1 Cones for general applications Nominal values Initial value Calculated values Cone angle, Rate of taper, C Series 1 Series 2 Degrees, minutes

30、and seconds “ Degrees Radians rad 120 2,094 395 10 1:0,288 675 1 90 1,570 796 33 1:0,500 000 0 75 1,308 996 94 1:0,651 612 7 60 1,047 197 55 1:0,866 025 4 45 0,785 398 16 1:1,207 106 8 30 0,523 598 78 1:1,866 025 4 1:3 18 55 28,719 9“ 18,924 644 42 0,330 297 35 1:4 14 15 0,117 7“ 14,250 032 70 0,248

31、 709 99 1:5 11 25 16,270 6“ 11,421 186 27 0,199 337 30 1:6 9 31 38,220 2“ 9,527 283 38 0,166 282 46 1:7 8 10 16,440 8“ 8,171 233 56 0,142 614 93 1:8 7 9 9,607 5“ 7,152 668 75 0,124 837 62 1:10 5 43 29,317 6“ 5,724 810 45 0,099 916 79 1:12 4 46 18,797 0“ 4,771 888 06 0,083 285 16 1:15 3 49 5,897 5“ 3

32、,818 304 87 0,066 641 99 1:20 2 51 51,092 5“ 2,864 192 37 0,049 989 59 1:30 1 54 34,857 0“ 1,909 682 51 0,033 330 25 1:50 1 8 45,158 6“ 1,145 877 40 0,019 999 33 1:100 34 22,630 9“ 0,572 953 02 0,009 999 92 1:200 17 11,321 9“ 0,286 478 30 0,004 999 99 1:500 6 52,529 5“ 0,114 591 52 0,002 000 00 NOTE

33、 1 For series 1, values from 120 to 1:3 are approximately in accordance with the R 10/2 series of preferred numbers, and values from 1:5 to 1:500 are in accordance with the R 10/3 series (see ISO 3). NOTE 2 The calculated values are for information only. BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011

34、All rights reserved 3Table 2 Selection of cones for particular application Nominal values International Standard number Applications Initial value Calculated values Cone angle, Rate of taper, C Degrees, minutes and seconds “ Degrees Radians rad 7:24 16 35 39,444 3“ 16,594 290 08 0,289 625 00 1:3,428

35、 571 4 ISO 297 Machine tool spindles, tool fits 1154 0,207 694 18 1:4,797 451 1 ISO 5237, ISO 8489-5 Cones and tubes for textile industry 840 0,151 261 87 1:6,598 441 5 ISO 324 ISO 575 ISO 8489-3, ISO 8489-4, 7 0,122 173 05 1:8,174 927 7 ISO 8489-2 1:9 a6 41 34,776 9” 6,359 660 24 0,110 997 01 IEC 6

36、0095-2 Terminals of lead acid starter battery 1 : 9,98 5 44 10,550 0 5,736 263 88 0,100 116 69 ISO 12164-1 Hollow taper interface 1:12,262 4 40 12,151 4“ 4,670 042 05 0,081 507 61 ISO 239 Jacobs taper No. 2 1:12,972 4 24 52,903 9“ 4,414 695 52 0,077 050 97 ISO 239 Jacobs taper No. 1 1:15,748 3 38 13

37、,442 9“ 3,637 067 47 0,063 478 80 ISO 239 Jacobs taper No. 33 6:100 3 26 12,177 6“ 3,436 716 00 0,059 982 01 1:16,666 666 7 ISO 594-1 ISO 595-1 ISO 595-2 Medical equipment 1:18,779 3 3 1,207 0“ 3,050 335 27 0,053 238 39 ISO 239 Jacobs taper No. 3 1:19,002 3 0 52,395 6“ 3,014 554 34 0,052 613 90 ISO

38、296 Morse taper No. 5 1:19,180 2 59 11,725 8“ 2,986 590 50 0,052 125 84 ISO 296 Morse taper No. 6 1:19,212 2 58 53,825 5“ 2,981 618 20 0,052 039 05 ISO 296 Morse taper No. 0 1:19,254 2 58 30,421 7“ 2,975 117 13 0,051 925 59 ISO 296 Morse taper No. 4 1:19,264 2 58 24,864 4“ 2,973 573 43 0,051 898 65

39、ISO 239 Jacobs taper No. 6 1:19,922 2 52 31,446 3“ 2,875 401 76 0,050 185 23 ISO 296 Morse taper No. 3 1:20,020 2 51 40,796 0“ 2,861 332 23 0,049 939 67 ISO 296 Morse taper No. 2 BS EN ISO 1119:2011ISO 1119:2011(E) 4 ISO 2011 All rights reservedTable 2 (continued) Nominal values International Standa

40、rd number Applications Initial value Calculated values Cone angle, Rate of taper, C Degrees, minutes and seconds “ Degrees Radians rad 1:20,047 2 51 26,928 3“ 2,857 480 08 0,049 872 44 ISO 296 Morse taper No. 1 1:20,288 2 49 24,780 2“ 2,823 550 06 0,049 280 25 ISO 239 Jacobs taper No. 0 1:23,904 2 2

41、3 47,624 4“ 2,396 562 32 0,041 827 90 ISO 296 Brown & Sharpe taper No. 1 to 3 1:28 2 2 45,817 4“ 2,046 060 38 0,035 710 49 ISO 10651-4 Resuscitators 1:38 1 30 27,708 0“ 1,507 696 67 0,026 314 27 ISO 368 Cones and tubes for textile industry 1:36 1 35 29,209 6“ 1,591 447 11 0,027 775 99 ISO 5356-1 Ana

42、esthetic equipment 1:40 1 25 56,351 6“ 1,432 319 89 0,024 998 70 1:64 0 53 42,822 0“ 0,895 228 34 0,015 624 68 ISO 368 Cones and tubes for textile industry aIn IEC 60095-2, the rate of taper is defined with a tolerance: 1 0,01:9. NOTE 1 The values in this table should be used only for the particular

43、 applications mentioned in the rightmost column. NOTE 2 The calculated values are for information only. BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved 5Annex A (informative) Relation to the GPS matrix model A.1 General For full details about the GPS matrix model, see ISO/TR 14638.

44、The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this do

45、cument, unless otherwise indicated. A.2 Information about this International Standard and its use This International Standard on conical tapers covers definitions of parameters and corresponding values for some applications. It should be completed by standards covering chain links 3 to 6 in order to

46、 allow an unambiguous understanding. A.3 Position in the GPS matrix model This International Standard is a general GPS standard, which influences chain links 1 and 2 of the chain of standards on angle in the general GPS matrix, as illustrated in Figure A.1. Global GPS standards General GPS matrixCha

47、in link number 1 2 3 4 5 6Size Distance Radius Angle Fundamental Form of line independent of datum Form of line dependent of datum GPS Form of surface independent of datum Form of surface dependent of datum standards Orientation Location Circular run-out Total run-out Datums Roughness profile Wavine

48、ss profile Primary profile Surface imperfections Edges Figure A.1 Position in the GPS matrix model BS EN ISO 1119:2011ISO 1119:2011(E) 6 ISO 2011 All rights reservedA.4 Related standards The related International Standards are those of the chains of standards indicated in Figure A.1. BS EN ISO 1119:2011ISO 1119:2011(E) ISO 2011 All rights reserved 7Bibliography 1 ISO 3:1973, Preferred numbers Series of preferred numbers 2 ISO 239:1999, Drill chuck tapers 3 ISO 296:1991, Machine tools Self-holding tapers for tool shanks 4 ISO 297:19