EN ISO 1179-2-2013 en Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2 Heavy-duty (S ser.pdf

1、BSI Standards PublicationBS EN ISO 1179-2:2013Connections for general useand fluid power Ports andstud ends with ISO 228-1threads with elastomeric ormetal-to-metal sealingPart 2: Heavy-duty (S series) and light-duty(L series) stud ends with elastomeric sealing(type E)BS EN ISO 1179-2:2013 BRITISH ST

2、ANDARDNational forewordThis British Standard is the UK implementation of EN ISO1179-2:2013. It supersedes BS EN ISO 1179-2:2008 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/18/-/4, Connectors and associated components.A list of organizations repre

3、sented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 7

4、8396 8ICS 23.100.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EU

5、ROPENNE EUROPISCHE NORM EN ISO 1179-2 November 2013 ICS 23.100.40 English Version Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric s

6、ealing (type E) (ISO 1179-2:2013) Raccordements pour applications gnrales et transmissions hydrauliques et pneumatiques - Orifices et lments mles filetage ISO 228-1 et joint en lastomre ou tanchit mtal sur mtal - Partie 2: lments mles de sries lgre (srie L) et lourde (srie S) avec joint en lastomre

7、(type E) (ISO 1179-2:2013) Leitungsanschlsse fr allgemeine Anwendung und Fluidtechnik - Einschraublcher und Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener Dichtkante - Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und leichte Reihe (L) (ISO 1

8、179-2:2013) This European Standard was approved by CEN on 12 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliog

9、raphical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsib

10、ility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republi

11、c of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALIS

12、ATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1179-2:2013 EBS EN ISO 1179-2:2013EN ISO 1179-2:2013 (E) 3 Foreword This

13、 document (EN ISO 1179-2:2013) has been prepared by Technical Committee ISO/TC 131 “Fluid power systems“ in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat of which is held by UNI. This European Standard shall be given the status of a na

14、tional standard, either by publication of an identical text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the latest by May 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig

15、hts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1179-2:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European St

16、andard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

17、Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1179-2:2013 has been approved by CEN as EN ISO 1179-2:2013 without any modification. BS EN ISO 1179-2:2013ISO 1179-2:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 1

18、2 Normative references 13 Terms and definitions . 24 Dimensions . 25 Requirements 25.1 Working pressure . 25.2 Performance 26 Elastomeric seals 27 Test methods . 27.1 Burst pressure test (failure pressure test) 27.2 Cyclic endurance (impulse) test . 37.3 Test report . 37.4 Re-use of components 38 De

19、signation of stud ends 39 Identification statement (reference to this part of ISO 1179) . 4Annex A (normative) Test data form for ISO 1179-1 port and ISO 1179-2 stud ends . 9Bibliography .10BS EN ISO 1179-2:2013ISO 1179-2:2013(E)ForewordISO (the International Organization for Standardization) is a w

20、orldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented

21、on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this

22、 document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Dir

23、ectives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development

24、 of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC

25、131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components.This second edition cancels and replaces the first edition (ISO 1179-2:2007), which has been technically revised.ISO 1179 consists of the following parts, under the general title Connections for general use a

26、nd fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing: Part 1: Threaded ports Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaini

27、ng ring (types G and H) Part 4: Stud ends for general use only with metal-to-metal sealing (type B)iv ISO 2013 All rights reservedBS EN ISO 1179-2:2013ISO 1179-2:2013(E)IntroductionIn fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within a cir

28、cuit. In general applications, a fluid can be conveyed under pressure. Components are connected through their threaded ports by fluid conductor connectors to tubes and pipes or to hose fittings and hoses.For threaded ports and stud ends specified in new designs in hydraulic fluid power applications,

29、 ISO/TC 131/SC 4 recommends that the ISO 6149 series be used because these International Standards specify ports and stud ends with metric threads and O-ring sealing and because the subcommittee would like to help users by recommending one preferred system. ISO/TC 131/SC 4 further recommends that th

30、readed ports and stud ends in accordance with the ISO 1179 series, ISO 9974 series and ISO 11926 series not be used for new designs in hydraulic fluid power applications; these International Standards are maintained because they specify ports and stud ends that are currently used in hydraulic system

31、s worldwide.For threaded ports and stud ends specified in new designs in pneumatic fluid power applications, ISO/TC 131/SC 4 recommends that ISO 16030 be used, except where products are to interface with ISO 7-1 threads, because the subcommittee would like to help users by recommending one preferred

32、 system. ISO/TC 131/SC 4 further recommends that threaded ports and stud ends in accordance with the ISO 1179 series not be used for new designs in pneumatic fluid power applications; these International Standards are maintained because they specify ports and stud ends that are currently used in pne

33、umatic systems worldwide.Significant testing over more than 35 years of use has confirmed the performance requirements of connection ends made from carbon steel. The stud end connections specified in ISO 1179-2, ISO 1179-3 and ISO 1179-4 apply to connectors detailed in ISO 8434-1, ISO 8434-2 and ISO

34、 8434-4. ISO 2013 All rights reserved vBS EN ISO 1179-2:2013BS EN ISO 1179-2:2013Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealin

35、g (type E)CAUTION The use of stud ends conforming to this part of ISO 1179 with ports conforming to the relevant parts of ISO 6149, ISO 9974 and ISO 11926 could lead to a hazardous situation.1 ScopeThis part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-dut

36、y (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them.Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 can be used at working pressures up to 63 MPa (630 bar). Light-duty (L seri

37、es) stud ends with type E sealing in accordance with this part of ISO 1179 can be used at working pressures up to 25 MPa (250 bar). The permissible working pressure depends upon size, materials, design, working conditions, application, etc.Conformance to the dimensional information in this part of I

38、SO 1179 does not guarantee rated performance. It is the responsibility of each manufacturer to perform testing according to the specification contained in this part of ISO 1179 in order to ensure that components made to this part of ISO 1179 comply with the performance ratings.NOTE 1 This part of IS

39、O 1179 applies to connectors detailed in ISO 8434-1 and ISO 8434-2.NOTE 2 The introduction of this part of ISO 1179 gives recommendations for ports and stud ends to be used for new designs in hydraulic and pneumatic fluid power applications.2 Normative referencesThe following documents, in whole or

40、in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 228-1, Pipe threads where pressure-tight

41、joints are not made on the threads Part 1: Dimensions, tolerances and designationISO 286-1, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fitsISO 286-2, Geometrical product specifications (GPS) ISO code system for

42、tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shaftsISO 5598, Fluid power systems and components VocabularyISO 9974-2, Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal

43、sealing Part 2: Stud ends with elastomeric sealing (type E)INTERNATIONAL STANDARD ISO 1179-2:2013(E) ISO 2013 All rights reserved 1BS EN ISO 1179-2:2013ISO 1179-2:2013(E)ISO 19879, Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections3 Terms and

44、 definitionsFor the purposes of this document, the terms and definitions given in ISO 5598 apply.4 DimensionsHeavy-duty (S series) and light-duty (L series) stud ends shall conform to the dimensions given in Figure 1 and Table 2. Hexagonal tolerances across flats shall be a maximum of h12 in accorda

45、nce with ISO 286-1 and ISO 286-2.5 Requirements5.1 Working pressureHeavy-duty (S series) and light-duty (L series) stud ends made of carbon steel shall be designed for use at the working pressures given in Table 3.5.2 PerformanceHeavy-duty (S series) and light-duty (L series) stud ends made of carbo

46、n steel shall meet or exceed the relevant burst and impulse pressures given in Table 3, when tested in accordance with Clause 7 and assembled using the torques listed in Table 5.6 Elastomeric sealsElastomeric seals for use with both heavy-duty (S series) and light-duty (L series) stud ends shall con

47、form to the dimensions given in Figure 2 and Table 4. Figure 3 shows the correct assembly of the stud end and elastomeric seal.7 Test methods7.1 Burst pressure test (failure pressure test)7.1.1 PrincipleThree samples shall be tested to confirm that heavy-duty (S series) and light-duty (L series) stu

48、d ends meet or exceed a ratio of 4:1 between the burst and working pressures without failure.7.1.2 Materials7.1.2.1 Test block and stud endsTest blocks shall be in accordance with the requirements specified in ISO 19879. Stud ends shall be made from carbon steel and be plated.7.1.2.2 Test sealsUnles

49、s otherwise specified, test seals shall meet the requirements specified in ISO 19879. Test seals shall conform to the dimensions given in Table 4.2 ISO 2013 All rights reservedBS EN ISO 1179-2:2013ISO 1179-2:2013(E)7.1.3 Procedures7.1.3.1 Thread lubricationFor testing only, threads and contact surfaces shall be lubricated in accordance with the requirements of ISO 19879.7.1.3.2 Stud end torqueStud ends shall be tested after application of the torques given in Table 5.7.1.3.3 Pressure rise rateThe rate of pres