EN ISO 1207-2011 en Slotted cheese head screws - Product grade A《开槽圆柱头螺钉 产品等级A》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 1207:2011Slotted cheese head screws Product grade A (ISO1207:2011)BS EN ISO 1207:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of

2、 EN ISO 1207:2011.It supersedes BS EN ISO 1207:1994 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication

3、does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 68770 9ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

4、of theStandards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1207 August 2011 ICS 21.060.10 Supersedes EN ISO 1207:1994English Version Slotted cheese head screws - Product grade A (ISO 12

5、07:2011) Vis mtaux tte cylindrique fendue - Grade A (ISO 1207:2011) Zylinderschrauben mit Schlitz - Produktklasse A (ISO 1207:2011) This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

6、giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three

7、official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodie

8、s of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United King

9、dom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1207:2011: EBS

10、EN ISO 1207:2011EN ISO 1207:2011 (E) 3 Foreword This document (EN ISO 1207:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of

11、 a national standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at the latest by February 2012. Attention is drawn to the possibility that some of the elements of this document may be the subjec

12、t of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1207:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement thi

13、s European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

14、 and the United Kingdom. Endorsement notice The text of ISO 1207:2011 has been approved by CEN as a EN ISO 1207:2011 without any modification. BS EN ISO 1207:2011ISO 1207:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federati

15、on of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee

16、. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance w

17、ith the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appr

18、oval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1207 was prepared by Technical Committ

19、ee ISO/TC 2, Fasteners, Subcommittee SC 11, Fasteners with metric external thread. This third edition cancels and replaces the second edition (ISO 1207:1992), which has been technically revised. BS EN ISO 1207:2011BS EN ISO 1207:2011INTERNATIONAL STANDARD ISO 1207:2011(E) ISO 2011 All rights reserve

20、d 1Slotted cheese head screws Product grade A 1 Scope This International Standard specifies the characteristics of slotted cheese head screws of product grade A and with threads from M1,6 to M10 inclusive. If, in special cases, specifications other than those listed in this International Standard ar

21、e required, they can be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1, ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition

22、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 261, ISO general purpose metric screw threads General plan ISO 898-1, Mechanical prope

23、rties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads M

24、edium quality ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fast

25、eners Electroplated coatings ISO 4753, Fasteners Ends of parts with external ISO metric thread ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements I

26、SO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts BS EN ISO 1207:2011ISO 1207:2011(E) 2 ISO 2011 All rights reservedISO 10683, Fasteners Non-electrolytically applied zinc fla

27、ke coatings ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners 3 Dimensions See Figure 1 and Table 1. The shank diameter is approximately equal to the pitch diameter or equal to the major thread diameter permissible. The symbols and descriptions of dimensions are specified in IS

28、O 225. aEdge may be rounded or flat. bAs-rolled end (RL) in accordance with ISO 4753. Figure 1 Slotted cheese head screws BS EN ISO 1207:2011ISO 1207:2011(E) ISO 2011 All rights reserved 3Table 1 Dimensions Dimensions in millimetres Thread, d M1,6 M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 Pb0,35 0,4 0,45 0,

29、5 0,6 0,7 0,8 1 1,25 1,5 a max. 0,7 0,8 0,9 1,0 1,2 1,4 1,6 2,0 2,5 3,0 b min. 25 25 25 25 38 38 38 38 38 38 damax. 2,0 2,6 3,1 3,6 4,1 4,7 5,7 6,8 9,2 11,2 nom. = max. 3,00 3,80 4,50 5,50 6,00 7,00 8,50 10,00 13,00 16,00 dkmin. 2,86 3,62 4,32 5,32 5,82 6,78 8,28 9,78 12,73 15,73 nom. = max. 1,10 1,

30、40 1,80 2,00 2,40 2,60 3,30 3,9 5,0 6,0 k min. 0,96 1,26 1,66 1,86 2,26 2,46 3,12 3,6 4,7 5,7 nom. 0,4 0,5 0,6 0,8 1 1,2 1,2 1,6 2 2,5 max. 0,60 0,70 0,80 1,00 1,20 1,51 1,51 1,91 2,31 2,81 n min. 0,46 0,56 0,66 0,86 1,06 1,26 1,26 1,66 2,06 2,56 r min. 0,10 0,10 0,10 0,10 0,10 0,20 0,20 0,25 0,40 0

31、,40 t min. 0,45 0,60 0,70 0,85 1,00 1,10 1,30 1,60 2,00 2,40 w min. 0,40 0,50 0,70 0,75 1,00 1,10 1,30 1,60 2,00 2,40 x max. 0,90 1,00 1,10 1,25 1,50 1,75 2,00 2,50 3,20 3,80 lcnom.amin. max. Approximate mass, in kilograms per 1 000 pieces ( = 7,85 kg/dm3) (for information only) 2 1,80 2,20 0,07 3 2

32、,80 3,20 0,082 0,16 0,272 4 3,76 4,24 0,094 0,179 0,302 0,515 5 4,76 5,24 0,105 0,198 0,332 0,56 0,786 1,09 6 5,76 6,24 0,117 0,217 0,362 0,604 0,845 1,17 2,06 8 7,71 8,29 0,14 0,254 0,422 0,692 0,966 1,33 2,3 3,56 10 9,71 10,29 0,163 0,291 0,482 0,78 1,08 1,47 2,55 3,92 7,85 12 11,65 12,35 0,186 0,

33、329 0,542 0,868 1,2 1,63 2,8 4,27 8,49 14,6 (14) 13,65 14,35 0,209 0,365 0,602 0,956 1,32 1,79 3,05 4,62 9,13 15,6 16 15,65 16,35 0,232 0,402 0,662 1,04 1,44 1,95 3,3 4,98 9,77 16,6 20 19,58 20,42 0,478 0,782 1,22 1,68 2,25 3,78 5,69 11 18,6 25 24,58 25,42 0,932 1,44 1,98 2,64 4,4 6,56 12,6 21,1 30

34、29,58 30,42 1,66 2,28 3,02 5,02 7,45 14,2 23,6 35 34,50 35,50 2,57 3,41 5,62 8,25 15,8 26,1 40 39,50 40,50 3,8 6,25 9,2 17,4 28,6 45 44,50 45,50 6,88 10 18,9 31,1 50 49,50 50,50 7,5 10,9 20,6 33,6 (55) 54,05 55,95 11,8 22,1 36,1 60 59,05 60,95 12,7 23,7 38,6 (65) 64,05 65,95 25,2 41,1 70 69,05 70,95

35、 26,8 43,6 (75) 74,05 75,95 28,3 46,1 80 79,05 80,95 29,8 48,6 NOTE Preferred lengths are those between the solid, bold, stepped lines. aSizes in parentheses should be avoided if possible. bP = pitch of the thread. cScrews with nominal lengths above the discontinuous line are threaded up to the head

36、 (b = l a). BS EN ISO 1207:2011ISO 1207:2011(E) 4 ISO 2011 All rights reserved4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standards Material Steel Stainless steel Non-ferrous metal General requirements International Standard

37、ISO 8992 Tolerance class 6g Thread International Standard ISO 261, ISO 965-2, ISO 965-3 Property class 4.8, 5.8 A2-50, A2-70 As agreed Mechanical property International Standard ISO 898-1 ISO 3506-1 ISO 8839 Product grade A Tolerances International Standard ISO 4759-1 As processed Requirements for e

38、lectroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Requirements for passivation are specified in ISO 16048. Requirements for electroplating are specified in ISO 4042. Finish Coating Additional requirements or other f

39、inishes or coatings shall be agreed between the supplier and the purchaser. Surface integrity Limits for surface discontinuities are specified in ISO 6157-1. Acceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE A slotted cheese head screw with thread M5, nominal length

40、 l = 20 mm and property class 4.8 is designated as follows: Cheese head screw ISO 1207 - M5 20 - 4.8 BS EN ISO 1207:2011ISO 1207:2011(E) ISO 2011 All rights reserved 5Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose bolts This page deliberately

41、left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Ch

42、arter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendm

43、ents or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be fou

44、nd on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou

45、may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to

46、orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowled

47、ge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevel

48、opments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bo