EN ISO 2507-3-2017 en Thermoplastics pipes and fittings - Vicat softening temperature - Part 3 Test conditions for acrylonitrile butadiene styrene (ABS) and acrylonitrile styrene a.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Thermoplastics pipes and fittings - Vicat softening temperaturePart 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittingsBS EN ISO 25073:2017Nation

2、al forewordThis British Standard is the UK implementation of EN ISO 25073:2017. It is identical to ISO 25073:1995. Together with BS EN ISO 25071:2017 and BS EN ISO 25072:2017, it supersedes BS EN 727:1995, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committe

3、e PRI/88, Plastics piping systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Instit

4、ution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96914 0ICS 23.040.45; 23.040.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2018.Amend

5、ments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 25073:2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 2507-3October 2017ICS 23.040.20; 23.040.45EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC

6、 Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN Ref. No. EN ISO 25073:2017: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersThermoplastics pipes and fittings Vicat softening temperature Part 3: Test conditions for acrylonitrile/butad

7、iene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 25073:1995)Tubes et raccords en matires thermoplastiques Temprature de ramollissement Vicat Partie 3: Conditions particulires dessai pour tubes et raccords en acrylonitrile/butadine/styrne (ABS) et en acrylonitr

8、ile/styrne/ester acrylique (ASA) (ISO 25073:1995)Rohre und Formstcke aus Thermoplasten VicatErweichungstemperatur Teil 3: Prfbedingungen fr Rohre und Formstcke aus AcrylnitrilButadienStyrol (ABS) und AcrylnitrilStyrolAcrylester (ASA) (ISO 25073:1995)This European Standard was approved by CEN on 19 S

9、eptember 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be o

10、btained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the C

11、ENCENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,

12、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 2507-3:2017 (E)European forewordThe text of ISO 25073:1995 has been prepared by Technical Committee IS

13、O/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 25073:2017 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.

14、This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the latest by October 2020.Attention is drawn to the possibility that some of t

15、he elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 727:1994.According to the CENCENELEC Internal Regulations, the national standards organizations of the following countries are

16、 bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por

17、tugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 25073:1995 has been approved by CEN as EN ISO 25073:2017 without any modification.2BS EN ISO 25073:2017ISO 2507-3:1995Foreword iv1 Scope .12 Normative reference .13

18、 Principle 14 Apparatus .15 Test pieces .16 Conditioning 26.1 Preliminary drying of test pieces 26.2 Conditioning of dried test pieces. 27 Procedure. 28 Test report . 2Annex A (informative) Acrylonitrile/butadiene/styrene (ABS) pipes and fittings Basic specification 3Annex (informative) Acrylonitril

19、e/styrene/acrylic ester (ASA) Basic specification . 4 ISO 1995 All rights reserved iiiContents PageBS EN ISO 25073:2017ISO 2507-3:1995ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Int

20、ernational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and nongovernmental, in liaison wi

21、th ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an

22、 International Standard requires approval by at least 75 % of the member bodies casting a vote.International Standard ISO 25073 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings an

23、d valves of plastic materials and their accessories Test methods and basic specifications .ISO 2507 consists of the following parts, under the general title Thermoplastics pipes and fittings Vicat softening temperature: Part 1: General test method Part 2: Test conditions for unplasticized poly(vinyl

24、 chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC-HI) pipes Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings Annexes A and of thi

25、s part of ISO 2507 are for information only.iv ISO 1995 All rights reservedBS EN ISO 25073:2017Thermoplastics pipes and fittings - Vicat softening temperature Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings1 ScopeThis

26、 part of ISO 2507 specifies the particular test conditions for determining the Vicat softening temperature of acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings.It also gives, for information, the corresponding basic specifications.NOTE 1 The gener

27、al test method for determining the Vicat softening temperature of thermoplastics pipes and fittings is given in ISO 25071.2 Normative referenceThe following standard contains provisions which, through reference in this text, constitute provisions of this part of ISO 2507. At the time of publication,

28、 the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this part of ISO 2507 are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently

29、valid International Standards.ISO 25071:1995, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method.3 PrincipleSee clause 3 in ISO 25071:1995, applicable to the thermoplastics materials covered by this part of ISO 2507.4 ApparatusSee clause 4 in ISO 25071:1995: us

30、e the oven (4.7) instead of the heating bath (4.5).5 Test piecesSee clause 5 in ISO 25071:1995.INTERNATIONAL STANDARD ISO 2507-3:1995 ISO 1995 All rights reserved 1BS EN ISO 25073:2017ISO 2507-3:19956 Conditioning6.1 Preliminary drying of test piecesImmediately before conditioning in accordance with

31、 6.2, predry the test pieces as follows: place the test pieces for 2 h in the oven (see ISO 25071:1995) controlled at 90 C 2 C; then let them cool in air at 23 C 2 C and (50 5) % relative humidity, for 15 min 1 min.6.2 Conditioning of dried test piecesCondition the dried test pieces (see 6.1) in acc

32、ordance with clause 6 of ISO 25071:1995.7 ProcedureSee clause 7 in ISO 25071:1995.8 Test reportSee clause 8 in ISO 25071:1995.2 ISO 1995 All rights reservedBS EN ISO 25073:2017ISO 2507-3:1995Annex A (informative) Acrylonitrile/butadiene/styrene (ABS) pipes and fittings Basic specificationWhen tested

33、 in accordance with this part of ISO 2507, the Vicat softening temperature (VST) of acrylonitrile/butadiene/styrene (ABS) pipes and fittings should be not less than 90 C.For specific applications which need more stringent requirements, minimum values greater than those specified above are given in t

34、he relevant product standards. ISO 1995 All rights reserved 3BS EN ISO 25073:2017ISO 2507-3:1995Annex (informative) Acrylonitrile/styrene/acrylic ester (ASA) Basic specificationWhen tested in accordance with this part of ISO 2507, the Vicat softening temperature (VST) of acrylonitrile/styrene/acryli

35、c ester (ASA) pipes and fittings should be not less than 90 C.For specific applications which need more stringent requirements, minimum values greater than those defined above are given in the relevant product standards.4 ISO 1995 All rights reservedBS EN ISO 25073:2017This page deliberately left bl

36、ankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limite

37、d.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format

38、 and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visi

39、ting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need

40、 international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or e

41、ntity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other

42、 person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is li

43、censed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use

44、 only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the docum

45、ent, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription

46、services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is ref

47、reshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribin

48、g Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on y

49、our intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the qual