EN ISO 3262-3-1998 en Extenders for Paints - Specifications and Methods of Test - Part 3 Blanc Fixe《涂料填充剂 规范和试验方法 第3部分 沉淀硫酸钡连同 BSISO 3262-3-1998其它部分》.pdf

1、STD.BS1 BS EN IS0 32b2-3-ENGL 1798 Lb24bb7 0733bO4 UT7 H BRITISH STANDARD Extenders for paints - Specifications and methods of test - Part 3: Blanc fixe The European Standard EN IS0 326231998 has the status of a British Standard ICs 87.060.10 SS EN IS0 l2623:1998 I NO COPYING WITHOUT BSI PERMISSION

2、EXCEPT AS PERMITTED BY COPYRIGHT LAW STD.BSI BS EN IS0 32b2-3-ENGL 1778 D Lb2Libb 0731b05 T33 D BS EN IS0 32623:1998 National foreword This British Standard is the English language version of EN IS0 32623.1998. It is identical with IS0 32623: 1998. Together with the other Parts of BS EN IS0 3262, it

3、 will supersede BS 1795:1976 which is declared obsolescent The UK participation in its preparation was entrusted to Technical Committee SW1, Pigments, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible inte them in the UK. - monitor related internat

4、ional and European developments and promulgate A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists nonnative references to intrnational

5、publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internationai Standards Correspondence Index“, or by using th

6、e “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ai the necessary provisions of a contract Users of British standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from l

7、egal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, pages ii and iii, a blank page, pages 1 to 4, the annex ZA page and a back cover. This British Standard, having been prepared under th

8、e direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 October 1998 O BSI 1998 ISBN O 580 30495 7 Amendments issued since publication AmdeNo. ID m, is the mass, in grams, of the precipitate. 7 Test report The

9、test report shall contain at least the following information: a) all details necessary to identify the product tested; b) a reference to this part of IS0 3262 (IS0 3262-3); c) the results of the tests and whether or not the product complies with the relevant specification limits; d) any deviation fr

10、om the test methods specified; e) the dates of the tests. 4 - STD.BSI BS EN IS0 32b2-3-ENGL L978 Lb2i-lbb7 073LbL5 982 EN IS0 3262-3:1998 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or

11、undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only w

12、hen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year IS0 787-2 1981 IS0 787-3 1979 IS0 787-5 1980 IS0 3262-1 1997 IS0 787-9 1981 IS03696 1987 - Title General methods of test for pigments and extenders - Pa

13、rt 2:Determination of matter volatile at 105 degrees C General methods of test for pigments and extenders - Part 3: Determination of matter soluble in water - Hot extraction method General methods of test for pigments and extenders - Part 5: Determination of oil absorption value Extenders for paints

14、 - Specifications and methods of test - Part 1 : Introduction and general test methods General methods of test for pigments and extenders - Part 9: Determination of pH value of aqueous suspension Water for analytical laboratory use - Specification and test methods - EN EN IS0 787-2 EN IS0 787-3 EN I

15、S0 787-5 EN IS0 3262-1 EN IS0 787-9 EN IS0 3696 Year 1995 1995 1995 1998 1995 1995 STD.BSI BS EN IS0 32b2-3-ENGL 1778 = Lb24bb7 0731bLb AL7 BS EN IS0 32623:1998 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent nationai body responsible for preparing

16、 British standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Chartr. Revisions British Standards are updated by amendment or revision. Users of British Standars should make sure that they possess the latest amendments or editions. It

17、is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front

18、cover. Tel: O181 996 9OOO. Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automa.tically receive the latest editions of standards. Buying standards Orders for all BSI, intemationai and foreign standards publications should be addresse

19、d to Customer Services. “el: O181 996 7000. Fax: O181 996 7001. In response to orders for internaiional standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range

20、of information on national, European and intedonai standards through its Library and its Technical Help to Exporters Service. Various BSI electronic infodon services are also available which give details on ali its products and services. Contact the Information Centre. Tel: O181 996 7111. Fax: O181

21、996 7048. Subscribiig members of BSI are kept up to date with standards developments and receive substantbi discounts on the purchase price of standards. For details of these and other benefits contact Membership Amon. Tel 0181 996 7002. Fax 0181 996 7001. COPyriBht Copyright subsists in all BSI pub

22、lications. BSI also holds the copyright, in the IJK, of the publications of the inhnaional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no exbract may be reproduced, stored in a retried system or transmitted in any form or by any means - electronic, p

23、hotocopying, recording or otherwise - without prior written permission hm BSI. This does not preclude the free use, in the com of implementing the standard, of necessary details such as symbols, and size, type or e designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if pennission is granted, the terms may include royaity payments or a licensing agreement. Details and actvice can be obtained from the Copyright Manager. Tel: 0181 996 7070.