EN ISO 4545-4-2005 en Metallic materials - Knoop hardness test - Part 4 Table of hardness values《金属材料 努氏硬度试验 第4部分 硬度值表 ISO 4545-4-2005》.pdf

1、BRITISH STANDARD BS EN ISO 4545-4:2005 Metallic materials Knoop hardness test Part 4: Table of hardness values The European Standard EN ISO 4545-4:2005 has the status of a British Standard ICS 77.040.10 BS EN ISO 4545-4:2005 This British Standard was published under the authority of the Standards Po

2、licy and Strategy Committee on 30 January 2006 BSI 30 January 2006 ISBN 0 580 47641 3 National foreword This British Standard is the official English language version of EN ISO 4545-4:2005. It is identical with ISO 4545-4:2005. The UK participation in its preparation was entrusted by Technical Commi

3、ttee ISE/NFE/4, Mechanical testing of metals, to Subcommittee ISE/NFE/4/5, Indentation/hardness testing, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement inter

4、national or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purp

5、ort to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committe

6、e any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO fore

7、word page, the ISO title page, pages ii and iii, a blank page, pages 1 to 22, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPE

8、NNE EUROPISCHENORM ENISO45454 November2005 ICS77.040.10 EnglishVersion MetallicmaterialsKnoophardnesstestPart4:Tableof hardnessvalues(ISO45454:2005) MatriauxmtalliquesEssaideduretKnoopPartie4: Tableaudesvaleursdeduret(ISO45454:2005) MetallischeWerkstoffeHrteprfungnachKnoopTeil4: TabellezurBestimmung

9、derHrtewerte(ISO45454:2005) ThisEuropeanStandardwasapprovedbyCENon28October2005. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcerni

10、ngs uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathast

11、hesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,Switze

12、rlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO45454:2005:E Foreword This docum

13、ent (EN ISO 4545-4:2005) has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of metals“ in collaboration with Technical Committee ECISS/TC 1 “Steel - Mechanical testing“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national sta

14、ndard, either by publication of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by May 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are boun

15、d to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and Unite

16、d Kingdom. Endorsement notice The text of ISO 4545-4:2005 has been approved by CEN as EN ISO 4545-4:2005 without any modifications. EN ISO 4545-4:2005 Reference number ISO 4545-4:2005(E)INTERNATIONAL STANDARD ISO 4545-4 First edition 2005-11-15 Metallic materials Knoop hardness test Part 4: Table of

17、 hardness values Matriaux mtalliques Essai de duret Knoop Partie 4: Tableau des valeurs de duret EN ISO 4545-4:2005ii iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International

18、Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, al

19、so take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committ

20、ees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the poss

21、ibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 4545-4 was prepared by Technical Committee ISO/TC 164, Mechanical hardness testing, Subcommittee SC 3, Hardness testing. ISO 45

22、45-4 cancels and replaces ISO 10250:1994, which has been technically revised. ISO 4545 consists of the following parts, under the general title Metallic materials Knoop hardness test: Part 1: Test method Part 2: Verification and calibration of testing machines Part 3: Calibration of reference blocks

23、 Part 4: Table of hardness values EN ISO 4545-4:2005blank1 Metallic materials Knoop hardness test Part 4: Table of hardness values 1 Scope This part of ISO 4545 gives a table for the calculation of Knoop hardness values for use in tests made on flat surfaces carried out in accordance with ISO 4545-1

24、. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4545-1, Metallic mat

25、erials Knoop hardness test Part 1: Test method ISO 4545-2, Metallic materials Knoop hardness test Part 2: Verification and calibration of testing machines 3 Calculation The Knoop hardness values in Table 1 have been calculated from the formula Test force HK Gravitational constant Projected area of i

26、ndentation = 222 0,102 0,102 1,451 0,070 28 F FF cd d d = = (1) where HK is the Knoop hardness; F is the test force, in newtons; d is the length in millimetres, of the long diagonal of the indentation; c is an indenter constant which equals tan 2 , 2tan 2 ideally c = 0,070 28; where and are the angl

27、es between the opposite edges at the vertex of the diamond pyramid, as defined in ISO 4545-2. EN ISO 4545-4:20052 NOTE Gravitational constant = 11 0,102 9,806 65 n g = where g nis the acceleration due to gravity. Table 1 covers a range of indentation diagonals d between 0,020 mm and 0,200 0 mm. EN I

28、SO 4545-4:2005EN ISO 4545-4:2005 3 Table 1 Test force N 0,098 07 0,196 1 0,245 2 0,490 3 0,980 7 1,961 2 2,942 0 4,903 9,807 Knoop hardness Indentation diagonal d mm HK 0,01 HK 0,02 HK 0,025 HK 0,05 HK 0,1 HK 0,2 HK 0,3 HK 0,5 HK 1 0,020 0 0,020 2 0,020 4 0,020 6 0,020 8 0,021 0 0,021 2 0,021 4 0,02

29、1 6 0,021 8 0,022 0 0,022 2 0,022 4 0,022 6 0,022 8 0,023 0 0,023 2 0,023 4 0,023 6 0,023 8 0,024 0 0,024 2 0,024 4 0,024 6 0,024 8 0,025 0 0,025 2 0,025 4 0,025 6 0,025 8 0,026 0 0,026 2 0,026 4 0,026 6 0,026 8 0,027 0 0,027 2 0,027 4 0,027 6 0,027 8 0,028 0 0,028 2 0,028 4 0,028 6 0,028 8 355,8 34

30、8,7 341,9 335,3 328,9 322,7 316,6 310,7 305,0 299,4 294,0 288,7 283,6 278,6 273,7 269,0 264,4 259,9 255,5 251,2 247,0 243,0 239,0 235,1 231,4 227,7 224,1 220,6 217,1 213,8 210,5 207,3 204,2 201,1 198,1 195,2 192,3 189,5 186,8 184,1 181,5 178,9 176,4 174,0 171,6 711,3 697,2 683,6 670,4 657,6 645,1 63

31、3,0 621,2 609,8 598,6 587,8 577,3 567,0 557,0 547,3 537,8 528,6 519,6 510,8 502,3 493,9 485,8 477,9 470,1 462,6 455,2 448,0 441,0 434,1 427,4 420,9 414,5 408,2 402,1 396,1 390,3 384,5 378,9 373,5 368,1 362,9 357,8 352,7 347,8 343,0 889,5 872,0 855,0 838,4 822,4 806,8 791,7 776,9 762,6 748,7 735,1 72

32、1,9 709,1 696,6 684,4 672,6 661,0 649,8 638,8 628,1 617,7 607,5 597,6 587,9 578,5 569,3 560,3 551,5 542,9 534,5 526,3 518,3 510,5 502,9 495,4 488,1 480,9 473,9 467,1 460,4 453,8 447,4 441,1 435,0 429,0 1 779 1 743 1 709 1 676 1 644 1 613 1 583 1 553 1 525 1 497 1 470 1 443 1 418 1 393 1 368 1 345 1

33、322 1 299 1 277 1 256 1 235 1 215 1 195 1 176 1 157 1 138 1 120 1 103 1 086 1 069 1 052 1 036 1 021 1 005 990,5 975,9 961,6 947,6 933,9 920,5 907,4 894,6 882,0 869,7 857,7 2 994 2 940 2 887 2 836 2 786 2 737 2 690 2 644 2 599 2 555 2 512 2 470 2 430 2 390 2 351 2 314 2 277 2 241 2 206 2 171 2 138 2

34、105 2 073 2 042 2 011 1 981 1 952 1 923 1 895 1 868 1 841 1 815 1 789 1 764 1 740 1 716 EN ISO 4545-4:2005 4 Table 1 (continued) Test force N 0,098 07 0,196 1 0,245 2 0,490 3 0,980 7 1,961 2 2,942 0 4,903 9,807 Knoop hardness Indentation diagonal d mm HK 0,01 HK 0,02 HK 0,025 HK 0,05 HK 0,1 HK 0,2 H

35、K 0,3 HK 0,5 HK 1 0,029 0 0,029 2 0,029 4 0,029 6 0,029 8 0,030 0 0,030 2 0,030 4 0,030 6 0,030 8 0,031 0 0,031 2 0,031 4 0,031 6 0,031 8 0,032 0 0,032 2 0,032 4 0,032 6 0,032 8 0,033 0 0,033 2 0,033 4 0,033 6 0,033 8 0,034 0 0,034 2 0,034 4 0,034 6 0,034 8 0,035 0 0,035 2 0,035 4 0,035 6 0,035 8 0,

36、036 0 0,036 2 0,036 4 0,036 6 0,036 8 0,037 0 0,037 2 0,037 4 0,037 6 0,037 8 169,2 166,9 164,6 162,4 160,2 158,1 156,0 154,0 152,0 150,0 148,1 146,2 144,3 142,5 140,7 139,0 137,2 135,6 133,9 132,3 130,7 129,1 127,6 126,0 124,6 123,1 121,7 120,3 118,9 117,5 116,2 114,8 113,6 112,3 111,0 109,8 108,6

37、107,4 106,2 105,1 103,9 102,8 101,7 100,7 99,59 338,3 333,7 329,1 324,7 320,4 316,1 311,9 307,8 303,8 299,9 296,0 292,3 288,6 284,9 281,3 277,8 274,4 271,0 267,7 264,4 261,2 258,1 255,0 252,0 249,0 246,1 243,2 240,4 237,6 234,9 232,2 229,6 227,0 224,5 222,0 219,5 217,1 214,7 212,4 210,1 207,8 205,6

38、203,4 201,2 199,1 423,1 417,3 411,6 406,1 400,7 395,3 390,1 385,0 380,0 375,1 370,2 365,5 360,9 356,3 351,8 347,5 343,2 338,9 334,8 330,7 326,7 322,8 318,9 315,2 311,4 307,8 304,2 300,7 297,2 293,8 290,4 287,2 283,9 280,7 277,6 274,5 271,5 268,5 265,6 262,7 259,9 257,1 254,4 251,7 249,0 845,9 834,3

39、823,0 812,0 801,1 790,4 780,0 769,8 759,8 749,9 740,3 730,8 721,5 712,4 703,5 694,7 686,1 677,7 669,4 661,3 653,3 645,4 637,7 630,1 622,7 615,4 608,2 601,2 594,2 587,4 580,7 574,2 567,7 561,3 555,1 548,9 542,9 536,9 531,1 525,3 519,6 514,1 508,6 503,2 497,9 1 692 1 669 1 646 1 624 1 602 1 581 1 560

40、1 540 1 520 1 500 1 481 1 462 1 443 1 425 1 407 1 390 1 372 1 356 1 339 1 323 1 307 1 291 1 276 1 260 1 246 1 231 1 217 1 203 1 189 1 175 1 162 1 148 1 136 1 123 1 110 1 098 1 086 1 074 1 062 1 051 1 039 1 028 1 017 1 007 995,9 2 999 2 960 2 923 2 886 2 849 2 813 2 778 2 744 2 710 2 677 2 644 2 612

41、2 581 2 550 2 520 2 490 2 461 2 432 2 404 2 376 2 349 2 322 2 296 2 270 2 245 2 220 2 195 2 171 2 147 2 124 2 101 2 078 2 056 2 034 2 012 1 991 2 988 5 Table 1 (continued) Test force N 0,098 07 0,196 1 0,245 2 0,490 3 0,980 7 1,961 2 2,942 0 4,903 9,807 Knoop hardness Indentation diagonal d mm HK 0,

42、01 HK 0,02 HK 0,025 HK 0,05 HK 0,1 HK 0,2 HK 0,3 HK 0,5 HK 1 0,038 0 0,038 2 0,038 4 0,038 6 0,038 8 0,039 0 0,039 2 0,039 4 0,039 6 0,039 8 0,040 0 0,040 2 0,040 4 0,040 6 0,040 8 0,041 0 0,041 2 0,041 4 0,041 6 0,041 8 0,042 0 0,042 2 0,042 4 0,042 6 0,042 8 0,043 0 0,043 2 0,043 4 0,043 6 0,043 8

43、 0,044 0 0,044 2 0,044 4 0,044 6 0,044 8 0,045 0 0,045 2 0,045 4 0,045 6 0,045 8 0,046 0 0,046 2 0,046 4 0,046 6 0,046 8 98,55 97,52 96,50 95,51 94,52 93,56 92,60 91,67 90,74 89,83 88,94 88,05 87,19 86,33 85,48 84,65 83,83 83,02 82,23 81,44 80,67 79,91 79,15 78,41 77,68 76,96 76,25 75,55 74,86 74,17

44、 73,50 72,84 72,18 71,54 70,90 70,27 69,65 69,04 68,43 67,84 67,25 66,67 66,10 65,53 64,97 197,0 195,0 192,9 190,9 189,0 187,0 185,1 183,3 181,4 179,6 177,8 176,0 174,3 172,6 170,9 169,2 167,6 166,0 164,4 162,8 161,3 159,8 158,3 156,8 155,3 153,9 152,4 151,0 149,7 148,3 147,0 145,6 144,3 143,0 141,8

45、 140,5 139,3 138,0 136,8 135,6 134,5 133,3 132,1 131,0 129,9 246,4 243,8 241,3 238,8 236,3 233,9 231,5 229,2 226,9 224,6 222,4 220,2 218,0 215,9 213,7 211,7 209,6 207,6 205,6 203,6 201,7 199,8 197,9 196,1 194,2 192,4 190,7 188,9 187,2 185,5 183,8 182,1 180,5 178,9 177,3 175,7 174,2 172,6 171,1 169,6

46、 168,1 166,7 165,3 163,8 162,4 492,7 487,5 482,4 477,5 472,6 467,7 463,0 458,3 453,7 449,1 444,6 440,2 435,9 431,6 427,4 423,2 419,1 415,1 411,1 407,2 403,3 399,5 395,7 392,0 388,4 384,7 381,2 377,7 374,2 370,8 367,5 364,1 360,9 357,6 354,5 351,3 348,2 345,1 342,1 339,1 336,2 333,3 330,4 327,6 324,8 985,5 975,2 965,0 955,1 945,2 935,6 926,0 916,7 907,4 898,3 889,4 880,5 871,9 863,3 854,8 846,5 838,3 83