EN ISO 4797-2015 en Laboratory glassware - Boiling flasks with conical ground joints《实验室玻璃器皿 锥形磨口接头烧瓶 (ISO 4797 2015)》.pdf

1、BSI Standards PublicationBS EN ISO 4797:2015Laboratory glassware Boiling flasks with conicalground jointsBS EN ISO 4797:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 4797:2015.It supersedes BS EN ISO 4797:2004 which is withdrawn.The UK participation i

2、n its preparation was entrusted to TechnicalCommittee LBI/1/2, Laboratory Equipment.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its c

3、orrectapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 83098 3ICS 71.040.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strat

4、egy Committee on 31 January 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4797 December 2015 ICS 71.040.20 Supersedes EN ISO 4797:2004English Version Laboratory glassware - Boiling flasks with conical ground jo

5、ints (ISO 4797:2015) Verrerie de laboratoire - Fioles coniques et ballons joint conique rod (ISO 4797:2015) Laborgerte aus Glas - Erlenmeyer-, Rund- und Stehkolben mit Kegelschliff (ISO 4797:2015) This European Standard was approved by CEN on 13 December 2015. CEN members are bound to comply with th

6、e CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managemen

7、t Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status

8、as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, N

9、etherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All

10、rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4797:2015 EBS EN ISO 4797:2015EN ISO 4797:2015 (E) 3 European foreword This document (EN ISO 4797:2015) has been prepared by Technical Committee ISO/TC 48 “Laboratory equipment“ in collab

11、oration with Technical Committee CEN/TC 332 “Laboratory equipment” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2016, and conflicting national stan

12、dards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 4

13、797:2004. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, F

14、rance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 4797:2015 has been approved by CEN as EN I

15、SO 4797:2015 without any modification. BS EN ISO 4797:2015ISO 4797:2015(E)Foreword iv1 Scope . 12 Normative references 13 Types . 14 Series of capacities . 15 Material 16 Dimensions . 17 Ground glass joints . 28 Thermal shock endurance 29 Marking 2 ISO 2015 All rights reserved iiiContents PageBS EN

16、ISO 4797:2015ISO 4797:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body intereste

17、d in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Com

18、mission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents

19、should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for

20、 identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the co

21、nvenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Forewo

22、rd - Supplementary information.The committee responsible for this document is ISO/TC 48, Laboratory equipment in collaboration with CEN/TC 332, Laboratory equipment.This third edition cancels and replaces the second edition (ISO 4797:2004), which has been technically revised to include the following

23、 changes: round-bottom flasks with nominal volumes of 3 l, 5 l, and 20 l have been added; overall heights of some round-bottom flasks of Series 1 (Table 3) have been modified; requirements for thermal shock endurance have been added.iv ISO 2015 All rights reservedBS EN ISO 4797:2015INTERNATIONAL STA

24、NDARD ISO 4797:2015(E)Laboratory glassware Boiling flasks with conical ground joints1 ScopeThis International Standard specifies requirements for an internationally acceptable series of boiling flasks with conical ground joints for general laboratory purposes.2 Normative referencesThe following docu

25、ments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 383, Laboratory glassw

26、are Interchangeable conical ground jointsISO 718, Laboratory glassware Thermal shock and thermal shock endurance Test methodsISO 1773, Laboratory glassware Narrow-necked boiling flasksISO 3585, Borosilicate glass 3.3 Properties3 TypesThe following three types of boiling flasks with conical ground jo

27、ints are specified:a) conical flasks;b) flat-bottom flasks;c) round-bottom flasks.4 Series of capacitiesTwo series are specified for each type of boiling flask with conical ground joints. The series differ in height and in selection of joint sizes. It is recommended that, in national standards, one

28、of these series is chosen.5 MaterialBoiling flasks shall be made from borosilicate glass 3.3 in accordance with ISO 3585, and shall be free from visible defects which might affect performance and free from any internal stress which would impair the performance of the flask.6 DimensionsThe external d

29、iameter of body of round-bottom flasks and flat-bottom flasks, the external diameter of body at the widest point of conical flasks and the minimum wall thickness shall comply with the dimensions specified in ISO 1773.The nominal overall height of the boiling flasks with conical ground joints shall b

30、e as specified in Table 1, Table 2 and Table 3. ISO 2015 All rights reserved 1BS EN ISO 4797:2015ISO 4797:2015(E)7 Ground glass jointsThe sizes of the conical joints fitted to the boiling flasks shall be as given in Table 1, Table 2 and Table 3. The joints shall comply with the requirements of ISO 3

31、83, k6 series.8 Thermal shock enduranceBoiling flasks with a nominal volume 3 000 ml shall have a thermal shock endurance of 150 C and boiling flasks with a nominal volume 3 000 ml shall have a thermal shock endurance of 100 C when tested in accordance with ISO 718.9 MarkingThe following inscription

32、s shall be permanently and legibly marked on all laboratory boiling flasks with conical ground joints:a) nominal volume of the boiling flask, for example “100 ml”;b) size of the conical ground joint, for example “29/32”;c) manufacturers and/or vendors name and/or mark;d) area with a surface suitable

33、 for marking with a pencil.It is recommended that reference be made on each flask to this International Standard, for example by the inscription “ISO 4797”.Table 1 Overall height and joint sizes for conical flasksNominal volumemlSeries 1 Series 2Overall height mmJoint sizes Nominal overall height mm

34、Joint sizes10 60 3 14/23 25 70 314/23 19/267014/23 19/2650 85 6 85100100 614/23 19/26 24/29 29/3210514/23 19/26 24/29 29/32250 140 619/26 24/29 29/32135 19/26 24/29 29/32 34/35500175 6 1701 000 220 7 24/29 29/32 34/35210 24/29 29/32 34/352 000270 7 2753 000 31034/35 45/405 000 3652 ISO 2015 All righ

35、ts reservedBS EN ISO 4797:2015ISO 4797:2015(E)Table 2 Overall height and joint sizes for flat-bottom flasksNominal volumemlSeries 1 Series 2Overall heightmmJoint sizes Nominal overall heightmmJoint sizes50 85 319/26 29/328519/26 24/29100 103 6 100 19/26 24/29 29/32 34/35250 130 6 125500 160 629/3214

36、524/29 29/32 34/351 000 187 6 1752 000 230 6 2104 000 255 45/40Table 3 Overall height and joint sizes for round-bottom flasksNominal volumemlSeries 1 Series 2Overall heightmmJoint sizes Nominal overall heightmmJoint sizes10 70 314/23 25 85 350 90 614/23 19/26 24/29 29/3290 14/23 19/26 29/32 24/29 34

37、/35100 105 6 110250 138 619/26 24/29 29/3213519/26 24/29 29/32 34/35500 163 624/29 29/32155 19/26 24/29 29/32 34/35 45/401 000 200 7 1852 000 240 7 2203 000 275 724/29 29/32 34/35 45/40 55/44 4 000 295 729/32 45/4027034/35 45/405 000 300 724/29 29/32 34/35 45/40 55/4427529/32 34/35 45/406 000 358 7

38、45/40 325 45/4010 000 380 7 45/40 35034/35 45/4020 000 435 10 55/44 ISO 2015 All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.

39、BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innov

40、ators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose st

41、andards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy a

42、nd download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordere

43、d from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and

44、 international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI

45、Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-

46、User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Sta

47、ndards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the

48、data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information

49、to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtaine