1、STD-BSI BS EN IS0 5b20-2-ENGL 1777 Lb24bb7 ObObh7b 84b BRITISH STANDARD MARINE SERIES Shipbuilding and marine structures- Filling connection for drinking water tanks Part 2. Components * n * The European Standard EN IS0 5620-2 : 1996 has the status of a British Standard ICs 47.020.30 NO COPYING WITH
2、OUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN IS0 5620-2 : 1997 BS EN IS0 5620-2 : 1997 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee SME/32, Steering Committee for shipbuilding and marine standards, upo
3、n which the following bodies were represented: British Marine Equipment Council British Maritime Technology British Motor Ship Owners Association British Waterways Board Chamber of Shipping Lloyds Register of Shipping Marine Safety Agency Ministry of Defence Shipbuilders and Shiprepairers Associatio
4、n This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1997 O BSI 1997 Amendments issued since publication Amd. No. 1 Date 1 Text affected The following BSI referenc
5、es relate to the work on this standard Committee reference: SMEi32 Draft for comment 91/73832 DC I l ISBN O 680 26660 8 I l BS EN IS0 5620-2 : 1997 National foreword This British Standard has been prepared by Technical Committee SMEM2 and is the English hguage version of EN IS0 5622 : 1996 Shipbuild
6、ing and rnamize structures - FiUing connection for dmnking water tanks -Part 2: Components, published by the European Committee for standardization (CEN). It is identical with IS0 5620-2 : 1992 published by the International Organization for Standasdization. It supersedes BS MA 85 : 1979 which is wi
7、thdrawn. EN IS0 5620-2 : 1996 was produced as a result of intrnationd discussions in which the United Kingdom took an active part. Cross-references The British Standards corresponding to the European standards referred to in the text are identical in number and titie with those given in annex zk Pub
8、lication referred to IS0 4026 : 1977 Corresponding British Standard BS 4168 Hmagon socket screws and wrench Ws: metric Series Part 2 : 1994 SpedfzCatim for hexagon socket set screuis with .fiat point Compliance with a British Standard does not of itself confer immunity from legal obligations. Sumnar
9、y of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN IS0 titie page, the EN IS0 foreword, the IS0 titie page, page ii, pages 1 to 6, the annex ZA page, a blank page, an inside back cover and a back cover. O BSI 1997 1 - EUROPEAN STANDARD NORME EUROPEENNE EU
10、ROPISCHE NORM EN IS0 5620-2 Novenikr 1996 ICs 41.020.30 Descriptors: See IS0 document English version Shipbuilding and marine structures - Filling connection for drinking water tanks - Part 2: Components (IS0 5620-2: 1 992) Construction navale et structures meritimes - Raccordement de remplissage de
11、s rCservoirs eau potable - Partie 2: Elements constitutifs (IS0 5620-2:1992) Schiffbau und Mcerestechnik - Obernahm-FlanschanschluB fr Trinkwassertanks - Teil 2: Einzelteile (IS0 5620-2:1992) This European Standard was approved by CEN on 1596-10-19. CEN members are bound to comply with the CEN/CENEL
12、EC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CE
13、N member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN mcmber into its oun language and notified to the Central Secretariat has the same status as the official versions. CEN me
14、mbers are the national standards bodies of Austria, Belgiun, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Cumnittee for Standardization Comit EuropCen de Normalisation Europi
15、sches Komitee fr Normung Central Secretariat: rue de Stassart,% 8-1050 Brussels 0 1996 Copyright reserved to CEN markrs Ref. No. EN IS0 5620-2:1996 E EN IS0 5620-2 : 1996 Foreword The text of the International Standard from Technical Committee ISOTTC 8 “Ships and mairne technology“ of the Internatio
16、nal Organization for Standarditation (EO) has been taken over as an European Standard by Technical Committee CEN/TC 300 “Sea-going vessels and mairne technology“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication o
17、f an identical text or by endorsement, at the latest by May 1997 and conflicting national standards shall be withdrawn at the latest by May 1997. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Sta
18、ndard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 5620-2:1992 has been approved by CEN as a European
19、Standard without any modification. NOTE: Normative references to International Standards are listed in annex ZA (normative). STD.BS1 BS EN IS0 5b20-2-ENGL 1997 lb24bb9 Obb901 T33 m EN IS0 5620-2 : 1996 INTERNATIONAL STANDARD IS0 First edition 1992-12-01 Shipbuilding and marine structures - Filling c
20、onnedion for drinking water tanks - Part 2: Components Construction navale et structures maritimes - Raccordement de remplissage des rservoirs eau potable - Partie 2: Elments constitutifs Reference number IS0 5620-2: 1992( E) STD-BSI BS EN IS0 5b20-2-ENGL 1777 LbZLibbS ObOb02 97T EN IS0 5620-2 : 199
21、6 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a
22、 technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take pari in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all mat
23、ters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an inter- national Standard requires approval by at least 75% of the member bodies casting a vote. International Standard IS0 562
24、0-2 was prepared by Technical Committee ISO/TC 8, Shipbuilding and marine structures. This first edition of IS0 5620-2 together with IS0 5620-1 cancel and re- place the first edition of IS0 5620, of which they constitute a technical revision. IS0 5620 consists of the following parts, under the gener
25、al title Shipbuilding and marine structures - Filling connection for drinking water tanks: - Part 1: General requirements - Part 2: Components DesdptOn: shipbulldlng, ships, water supply, potable water, tanks (contalners), plplng, water plpellnes, pipe jolnts, connecting joints, components, speclfic
26、atlons, dimensions, designation. ii STD.BSI BS EN IS0 5620-2-ENGL L997 Lb2Ybb OhOb903 Bub a EN IS0 5620-2 : 1996 Shipbuilding and marine structures - Filling connection for drinking water tanks - Part 2 Components 1 Scope IS0 5620 specifies the drinking water connection aboard ships for attachment o
27、f piping from another ship or from a land distribution system. This pari of IS0 5620 specifies the technical details of the components of the filling connection and lays down the designation of the main components such as flanges, securing bolts and gasket. * * r) NOTE 1 Part 1 of IS0 5820 specifies
28、 the general re- quirements, the composition and the designation of the complete filling connection. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 5620. At the time of publication, the editions indic
29、ated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 5620 are encouraged to investi- gate the possibility of applying the most recent edi- tions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid In- t
30、ernational Standards. IS0 630:1980. Structural steels. IS0 683-1:1987, Heat-treatable steels, alloy steels and free-cutting steels - Part I: Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products. IS0 1302:1992, Technical drawings - Method of in- dicating surfac
31、e texture. IS0 2341:1986, Clevis pins with head. IS0 4016:1988, Hexagon head bolts - Product grade C. IS0 4026:1977, Hexagon socket set screws with flat point. IS0 5620-1:1992, Shipbuilding and marine structures - Filling connection for drinking water tanks - Part 1: General requirements. 1 - STD.BS
32、I BS EN IS0 5620-2-ENGL 1997 m Lb24669 ObObOLi 7Li2 m EN IS0 6620-2 : 1996 3 Supply watering flange The supply watering flange (flange A in IS0 5620-1) shall be used for the piping or hose line to the drinking water supply source. 3.1 Dimensions The dimensions of the supply watering flange shall be
33、as shown in figure i. 3.2 Material The supply watering flange shall be made of steel in accordance with IS0 630, grade Fe 360, as the mini- mum quality. -I Alternatively shipquality steel plate grade A may be used, provided that it has equivalent mechanical and welding properties. 3.3 Designation A
34、supply watering flange (flange A) that meets the requirements of this part of IS0 5620 shall be des- ignated: Flange IS0 56202 - A NOTE - Positioning of holes shall be in accordance with IS0 5820-1. Dimensions in millimetres Surface texture in accordance with IS0 1302 Figure 1 - Dlmenslons of supply
35、 watering fiange 2 STD.BSI BS EN IS0 5b20-2-ENGL 1997 m Lb24bb9 ObOb905 b87 m EN IS0 5620-2 : 1996 4 Ship wateridg flange 4.1 Dimensions The dimensions of the ship watering flange (flange B in IS0 5620-1) shall be as given in figure2. 4.2 Matcrlal The ship watering flange shall be made of steel in a
36、ccordance with IS0 630, grade Fe 360, as the mini- mum quality. Alternatively ship-quality steel plate grade A may be used, provided that it has equivalent mechanical and welding properties. 4.3 Designation A ship watering flange (flange B) that meets the re- quirements of this part of IS0 5620 shal
37、l be desig- nated: Flange IS0 56202 - B Dimensions In miiiimetres Surface texture In accordance with IS0 1302 t 185 1 I i turned op faced /Rz #O NOTE - Positioning of holes shall be in accordance with IS0 5620-1. Figure 2 - Dimensions for ship watering flange 3 STD*BSI BS EN IS0 5b20-2-ENGL 1777 1b2
38、Libb7 ObOb70b 515 EN IS0 5620-2 : 1996 5 Shlp watering blind flange 5.1 Dlmenslons The dimensions of the ship watering blind flange (flange C in IS0 5620.1) shalt. be as given in flgure 3. 5.2 Material The ship watering blind flange shall be made of steel in accordance with IS0 630, grade Fe 360, as
39、 the minimum quality. Alternatively ship-quality steel plate grade A may be used, provided that it has equivalent mechanical and welding properties. 5.3 Deslgnation A ship watering blind flange (flange C) that meets the requirements of this part of IS0 5620 shall be designated: Flange IS0 5620-2 - C
40、 Dimensions in millimetres Surface texture in accordance with IS0 13132 NOTE - Positioning of holes shall be in accordance with IS0 5620-1. Figure 3 - Dimensions of ship watering Mind flange 4 - STD-BSI BS EN IS0 5b20-2-ENGL 1797 lb24bb9 OhOb707 451 M EN IS0 5620-2 : 1996 6 Securing boit 6.1 Dimensi
41、ons The dimensions of the securing bolt (code letter D in IS0 5620-1) shall be as given in figure4. Where semi-finished products are used, a clevis pin ac- cording to IS0 2341 - A - 20 x 85 - St shall be used. 6.2 Material The securing bolt shall be made of non-corrodible steel in accordance with IS
42、0 683-1, grade H as the minimum quality. 6.3 Designation A securing bolt (code letter D) that meets the re- quirements of this part of IS0 5620 shall be desig- nated: Bolt IS0 5820-2 - D 7 Gasket 7.1 Dimensions - II L - = _. I - The dimensions of the gasket (code letter E in IS0 5620-1) shall be as
43、given in figures. * * rn 7.2 Material Gaskets shall be made of seawater-resistant elastomer material, which is acceptable for drinking water. 7.3 Designation A gasket (code letter E) that meets the requirements of this part of IS0 5620 shall be designated: Gasket IS0 5620-2 - E 8 Stud-bolts Stud-bol
44、ts M16 of non-corrodible steel of grade H in accordance with IS0 683-1. as the minimum quality, shall be used and fitted in the watering flange. Alternatively hexagon socket set screws with a flat point in accordance with IS0 4026 or normal hexagon bolts in accordance with IS0 4016, both made of non
45、-corrodible steel, may be used. 9 Nuts Hexagon cap nuts M16 shall be used. They shall be made of non-corrodible steel grade H in accordance with IS0 683-1, as the minimum quality. Alternatively ordinary hexagon nuts Ml6 may be used, provided that they are of same material. 10 Padlock The hinged lock
46、ing shall have a width of approxi- mately 30 mm, with its diameter approximately 8 mm. The internal components of the padlock shall be of non-corrodible metallic materials (for instance brass). All other components of the padlock may be made of steel. The padlock should have an eye serving for the c
47、onnection of the securing chain. 11 Securing chain Securing chains shall be made of non-corrodible steel. The securing chain should have at one end an S- shaped hook for fastening the chain at the securing bolt: on the other end it should have a securing ring for padlock connection. Common small cha
48、ins without quality requirements may be used, for instance knotted link chains as shown in figure6. 5 Dimensions in millimetres Surface texture in accordance with IS0 1302 Flgure 4 - Dlmensions of securlng bolt Dimansions in millimetres i I Figure S - Dlmsnslonr of gasket rs- Flgure S - Example for
49、seeuring chain 6 STD.BSI BS EN IS0 5bZ-Z-ENGL 1997 Lb24bb7 0bUb907 22Y EN IS0 5620-2 : 1996 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only whe
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1