EN ISO 5821-2009 en Resistance welding - Spot welding electrode caps《电阻焊接 点焊电极帽接头》.pdf

1、BS EN ISO5821:2009ICS 25.160.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDResistance welding Spot welding electrodecaps (ISO 5821:2009)This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 March2010 BSI 201

2、0ISBN 978 0 580 65944 7Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 5821:2009National forewordThis British Standard is the UK implementation of EN ISO 5821:2009. Itsupersedes BS EN 25821:1992 which is withdrawn.The UK participation in its preparation was entrusted to Technica

3、lCommittee WEE/29, Resistance welding.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British S

4、tandard cannot confer immunityfrom legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 5821 November 2009 ICS 25.160.30 English Version Resistance welding - Spot welding electrode caps (ISO 5821:2009) Soudage par rsistance - Embouts amovibles de pointes dlectrodes pour soudage

5、 par points (ISO 5821:2009) Widerstandsschweien - Punktschwei-Elektrodenkappen (ISO 5821:2009) This European Standard was approved by CEN on 8 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

6、 status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa

7、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Re

8、public, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN

9、DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 5821:2009: EBS EN ISO 5821:2009EN ISO 5821:2009 (E) 3 Foreword The text o

10、f ISO 5821:2009 has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 5821:2009 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European

11、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of thi

12、s document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stan

13、dard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

14、 Endorsement notice The text of ISO 5821:2009 has been approved by CEN as a EN ISO 5821:2009 without any modification. BS EN ISO 5821:2009ISO 5821:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards

15、 bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organiza

16、tions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in t

17、he ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of

18、 the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5821 was prepared by Technical Committee ISO/TC 44, Welding an

19、d allied processes, Subcommittee SC 6, Resistance welding and allied mechanical joining. This second edition cancels and replaces the first edition (ISO 5821:1979) which has been technically revised. Requests for official interpretations of any aspect of this International Standard should be directe

20、d to the Secretariat of ISO/TC 44/SC 6 via your national standards body, a complete listing of which can be found at www.iso.org. BS EN ISO 5821:2009BS EN ISO 5821:2009INTERNATIONAL STANDARD ISO 5821:2009(E) ISO 2009 All rights reserved 1Resistance welding Spot welding electrode caps 1 Scope This In

21、ternational Standard specifies the dimensions and tolerances of resistance spot welding electrode caps, where a female taper (see ISO 1089) is used to fix the cap to an electrode adaptor (see ISO 5183-1 and ISO 5183-2). It applies only to electrode caps for which the electrode force, FE, given for d

22、iameter d1in Table 2 and Table A.2 is not exceeded. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

23、 any amendments) applies. ISO 1089, Electrode taper fits for spot welding equipment Dimensions ISO 5182, Resistance welding Materials for electrodes and ancillary equipment ISO 5183-1, Resistance welding equipment Electrode adaptors, male taper 1:10 Part 1: Conical fixing, taper 1:10 ISO 5183-2, Res

24、istance welding equipment Electrode adaptors, male taper 1:10 Part 2: Parallel shank fixing for end-thrust electrodes ISO 17677-1, Resistance welding Vocabulary Part 1: Spot, projection and seam welding 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO

25、 17677-1 apply. 4 Dimensions and tolerances The dimensions shall be as given in Table 1 and Figure 1 for taper 1:10 and as given in Annex A for taper 1:9,6. ISO 1089 shall be used to provide the taper dimensions. Tolerances shall be as given in Table 3. To enlarge the application potential of this I

26、nternational Standard, common variations of the base types are specified in Table 1. Preferred values are printed in bold-face. Depending on the working stroke of the guns, two additional lengths, l1, are offered to allow optimized lifetimes of the caps using tip dressers. D2and R1allow options to a

27、dapt the contact areas to different electrode indentations and nugget sizes. BS EN ISO 5821:2009ISO 5821:2009(E) 2 ISO 2009 All rights reservedThe electrode force, FE, given for diameter d1in Table 2 and Table A.2 should not be exceeded. Table 1 Dimensions for taper 1:10 (preferred values are printe

28、d in bold-face) Linear dimensions in millimetres Type d1d2d3l1l2l3e R1R2 13 10,0 18,0 21,0 24,0 8,5 30 65 100 16 12,0 20,0 23,0 25,0 10,5 40 70 100 A0 20 15,0 22,0 25,0 28,0 12,0 50 75 100 13 5,0 6,0 7,0 10,0 18,0 21,0 24,0 8,5 30 flat 30 45 16 6,0 7,0 8,0 12,0 20,0 23,0 25,0 10,5 40 flat 50 30 45 B

29、0 20 8,0 9,0 10,0 15,0 22,0 25,0 28,0 12,0 50 flat 75 30 45 13 10,0 18,0 21,0 24,0 8,5 16 12,0 20,0 23,0 25,0 10,5 C0 20 15,0 22,0 25,0 28,0 12,0 13 5,0 10,0 18,0 21,0 24,0 8,5 3,0 32 flat 30 45 60 16 6,0 12,0 20,0 23,0 25,0 10,5 4,0 40 flat 30 45 60 D0 20 8,0 15,0 22,0 25,0 28,0 12,0 5,0 50 flat 30

30、 45 60 13 10,0 18,0 21,0 24,0 8,5 8,0 5 20 16 12,0 20,0 23,0 25,0 10,5 10,5 6 20 E0 20 15,0 22,0 25,0 28,0 12,0 12,0 8 20 13 10,0 18,0 21,0 24,0 8,5 6,5 16 12,0 20,0 23,0 25,0 10,5 8 F0 20 15,0 22,0 25,0 28,0 12,0 10 13 5,0 5,5 6,0 10,0 18,0 21,0 24,0 8,5 6,0 50 63 flat 6,5 16 5,5 6,5 8,0 12,0 20,0

31、23,0 25,0 10,5 7,5 50 80 flat 8,0 F1 20 6,0 7,0 8,0 15,0 22,0 25,0 28,0 12,0 9,5 50 100 flat 10,0 13 5,0 10,0 18,0 21,0 24,0 8,5 10,5 32 flat 5,0 1520 16 6,0 12,0 20,0 23,0 25,0 10,5 12,0 40 flat 6,0 15 17 G0 20 8,0 15,0 22,0 25,0 28,0 12,0 10,0 50 flat 8,0 22,5 20 NOTE For tolerances on dimensions,

32、 see Table 3. BS EN ISO 5821:2009ISO 5821:2009(E) ISO 2009 All rights reserved 3Table 2 Recommended maximum electrode force, FE, depending on the hardness of the caps, given for diameter d1, taper 1:10 d1Electrode force FEHardness u 150 HB Electrode force FEHardness 150 HB mm kN kN 13 2,5 3,5 16 4,0

33、 5,5 20 6,3 7,5 Table 3 Tolerances on dimensions Dimension Tolerance d1 0,15 mm d2 0,2 mm d300,1mm l1 0,5 mm l2 0,5 mm l3 0,5 mm l1 l2 R1u 30 mm 0,5 mm R1 30 mm 2,0 mm R2 0,5 mm 1 T06c 0,02 mm Tangle of taper c circularity BS EN ISO 5821:2009ISO 5821:2009(E) 4 ISO 2009 All rights reservedaTolerance

34、for Tapplies. Type A0 Type B0 Type C0 Type D0 Type E0 Type F0 Type F1 Type G0 NOTE Types A0, B0, C0 and D0 denote representative forms of water hole configuration. “S” denotes spherical radiuses. Figure 1 Female electrode caps 5 Designation EXAMPLES A spot welding electrode cap type B0 (i.e. taper 1

35、:10), width d1= 16 mm, length l1= 20 mm, R1= 30 mm, d2= 8 mm and = 45, is designated as follows: Spot welding electrode cap ISO 5821 B0 16 20 30 8 45 A spot welding electrode cap type A0 (i.e. taper 1:10), width d1= 20 mm, length l1= 22 mm, R1= 50 mm (d2and are not applicable), is designated as foll

36、ows: Spot welding electrode cap ISO 5821 A0 20 22 50 A spot welding electrode cap type C0 (i.e. taper 1:10), width d1= 13 mm, length l1= 18 mm (R1, d2and are not applicable), is designated as follows: Spot welding electrode cap ISO 5821 C0 13 18 BS EN ISO 5821:2009ISO 5821:2009(E) ISO 2009 All right

37、s reserved 56 Material Materials in accordance with ISO 5182 shall be used. 7 Marking The package shall be marked with the full designation and material used, for example in accordance with the first example in Clause 5. ISO 5821 B0 16 20 30 8 45 A2/2 BS EN ISO 5821:2009ISO 5821:2009(E) 6 ISO 2009 A

38、ll rights reservedAnnex A (normative) Alternative types and dimensions of female electrode caps A.1 General The classification according to Table 1 is mainly based on the previous edition of this International Standard. The classification according to Annex A is mainly based on standards specifying

39、taper 1:9,6. Application of either type of classification designation identifies a product as classified according to this International Standard. Annex A has been incorporated to improve the market relevance of this International Standard, especially in countries where taper 1:9,6 is still used. Al

40、though it is recognised that the 1:10 taper is not universally used currently, it is felt that a move to a 1:10 taper would be in the interest of global relevance and therefore it is intended to delete this annex in a future revision. A.2 Types and dimensions Table A.1 and Figure A.1 show alternativ

41、e types of female electrode caps; the corresponding symbols between Table 1 and Figure 1 and this annex are in parentheses. Tolerances shall be as given in Table 3. BS EN ISO 5821:2009ISO 5821:2009(E) ISO 2009 All rights reserved 7Table A.1 Alternative dimensions with taper 1:9,6 Linear dimensions i

42、n millimetres d1(M) Type Table 1 functional equivalent l1 l2(G) d2(D) (N) R1(R) (S) l1(L) d3(J) l2(P) FA G0 4,8 9,5 4,1 1520 FB F1 4,8 6,4 4,1 FC C0 FD D0 4,8 50 FE B0 4,8 45 12,7 FF A0 11,7 50,1 21,3 10,01 9,1 13 FB F1 9,5 6 8 20 10 9 FA G0 6,4 12,7 5,6 17 FB F1 6,4 9,5 5,6 FC C0 FD D0 6,4 45 FE B0

43、 6,4 45 15,8 FF A0 9,4 50,1 22,35 12,56 9,9 FA G0 12,1 6 8 23 12,6 10,9 16 FB F1 11,5 6 8 23 12,6 10 19 FB F1 8,5 8 8 25 14 15 FA G0 7,1 19,1 7,1 20 FB F1 7,1 9,5 7,1 FC C0 FD D0 7,1 45 FE B0 7,1 45 19,1 FF A0 9,4 101,6 25,4 15,88 11,0NOTE 12,7 mm = 1/2 inch; 15,8 mm = 5/8 inch; 19,1 mm = 3/4 inch.

44、Table A.2 Recommended maximum electrode force, FE, given for diameter d1, taper 1:9,6 d1Electrode force FEHardness u 150 HB Electrode force FEHardness 150 HB mm kN kN 12,7 2,6 3,6 15,8 4,9 6,8 19,1 7,6 9,1 BS EN ISO 5821:2009ISO 5821:2009(E) 8 ISO 2009 All rights reservedType FA Type FB Type FC Type

45、 FD Type FE Type FF aTaper 1:9,6. Figure A.1 Alternative female electrode caps A.3 Designation EXAMPLE A spot welding electrode cap type FA (i.e. taper 1:9,6) in accordance with Table A.1, width d1= 12,7 mm, is designated as follows: Spot welding electrode cap ISO 5821 FA 12,7 BS EN ISO 5821:2009ISO

46、 5821:2009(E) ISO 2009 All rights reserved 9Bibliography 1 ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts 2 ISO 1119, Geometrical Product Specifications (GPS) Series of conical tapers and taper angles 3 ISO 5822, Spot we

47、lding equipment Taper plug gauges and taper ring gauges BS EN ISO5821:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they poss