EN ISO 6145-6-2017 en Gas analysis - Preparation of calibration gas mixtures using dynamic methods - Part 6 Critical flow orifices.pdf

1、Gas analysis - Preparation of calibration gas mixtures using dynamic methodsPart 6: Critical flow orificesBS EN ISO 6145-6:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6145-6 August 2017 ICS 71.040.40 Su

2、persedes EN ISO 6145-6:2008English Version Gas analysis - Preparation of calibration gas mixtures using dynamic methods - Part 6: Critical flow orifices (ISO 6145-6:2017) Analyse des gaz - Prparation des mlanges de gaz pour talonnage laide de mthodes volumtriques dynamiques - Partie 6: Orifices de d

3、bit critiques (ISO 6145-6:2017) Gasanalyse - Herstellung von Kalibriergasgemischen mit Hilfe von dynamisch-volumetrischen Verfahren - Teil 6: Kritische Dsen (ISO 6145-6:2017) This European Standard was approved by CEN on 7 August 2017. CEN members are bound to comply with the CEN/CENELEC Internal Re

4、gulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN me

5、mber. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

6、 CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan

7、d, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploi

8、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6145-6:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 6145-6:2017. It supersedes BS EN ISO 6145-6:2008, which is withdrawn.The UK participation in its preparation was ent

9、rusted to Technical Committee PTI/15, Natural Gas and Gas Analysis.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicat

10、ion. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 79572 5ICS 71.040.40Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committe

11、e on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 6145-6:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6145-6 August 2017 ICS 71.040.40 Supersedes EN ISO 6145-6:2008English Version Gas analysis - Preparation of calibration

12、 gas mixtures using dynamic methods - Part 6: Critical flow orifices (ISO 6145-6:2017) Analyse des gaz - Prparation des mlanges de gaz pour talonnage laide de mthodes volumtriques dynamiques - Partie 6: Orifices de dbit critiques (ISO 6145-6:2017) Gasanalyse - Herstellung von Kalibriergasgemischen m

13、it Hilfe von dynamisch-volumetrischen Verfahren - Teil 6: Kritische Dsen (ISO 6145-6:2017) This European Standard was approved by CEN on 7 August 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the statu

14、s of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Ger

15、man). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croati

16、a, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

17、 and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref

18、. No. EN ISO 6145-6:2017 EBS EN ISO 6145-6:2017EN ISO 6145-6:2017 (E) 3 European foreword This document (EN ISO 6145-6:2017) has been prepared by Technical Committee ISO/TC 158 “Analysis of gases”. This European Standard shall be given the status of a national standard, either by publication of an i

19、dentical text or by endorsement, at the latest by February 2018, and conflicting national standards shall be withdrawn at the latest by February 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsib

20、le for identifying any or all such patent rights. This document supersedes EN ISO 6145-6:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus

21、, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

22、United Kingdom. Endorsement notice The text of ISO 6145-6:2017 has been approved by CEN as EN ISO 6145-6:2017 without any modification. ISO 6145-6:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The w

23、ork of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-govern

24、mental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in t

25、he ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the p

26、ossibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO lis

27、t of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, on the meaning of ISO specific terms and expressions r

28、elated to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 158, Analysis of g

29、ases.This third edition cancels and replaces the second edition (ISO 6145-6:2003) which has been technically revised.A list of all parts in the ISO 6145 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 6145-6:2017ISO 6145-6:2017(E)ForewordISO (the International Organiz

30、ation for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established

31、 has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Th

32、e procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the e

33、ditorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any paten

34、t rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For

35、 an explanation on the voluntary nature of standards, on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: ww

36、w .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 158, Analysis of gases.This third edition cancels and replaces the second edition (ISO 6145-6:2003) which has been technically revised.A list of all parts in the ISO 6145 series can be found on the ISO website.

37、iv ISO 2017 All rights reservedBS EN ISO 6145-6:2017INTERNATIONAL STANDARD ISO 6145-6:2017(E)Gas analysis Preparation of calibration gas mixtures using dynamic methods Part 6: Critical flow orifices1 ScopeThis document specifies a method for the dynamic preparation of calibration gas mixtures contai

38、ning at least two gases (usually one of them is a complementary gas) from pure gases or gas pre-mixtures using critical flow orifices systems.The method applies principally to the preparation of mixtures of non-reactive gases that do not react with any of the materials forming the gas circuit inside

39、 the critical flow orifices system or auxiliary equipment. It has the merit of allowing multi-component mixtures to be prepared as readily as binary mixtures if an appropriate number of critical flow orifices are used.By selecting appropriate combinations of critical flow orifices, a dilution ratio

40、of 1 104is achievable.Although it is more particularly applicable to the preparation of gas mixtures at atmospheric pressure, the method also offers the possibility of preparing calibration gas mixtures at pressures greater than atmospheric. The upstream pressure will need to be at least two times h

41、igher than downstream pressure.The range of flow rates covered by this document extends from 1 ml/min to 10 l/min.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references,

42、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 6143, Gas analysis Comparison methods for determining and checking the composition of calibration gas mixturesISO 7504, Gas analysis VocabularyISO 9300, Measu

43、rement of gas flow by means of critical flow Venturi nozzlesISO 12963, Gas analysis Comparison methods for the determination of the composition of gas mixtures based on one- and two-point calibrationISO 16664, Gas analysis Handling of calibration gases and gas mixtures Guidelines3 Terms and definiti

44、onsFor the purposes of this document, the terms and definitions given in ISO 9300, ISO 7504 and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsi

45、ng platform: available at h t t p :/ www .iso .org/ obp ISO 2017 All rights reserved 1BS EN ISO 6145-6:2017INTERNATIONAL STANDARD ISO 6145-6:2017(E)Gas analysis Preparation of calibration gas mixtures using dynamic methods Part 6: Critical flow orifices1 ScopeThis document specifies a method for the

46、 dynamic preparation of calibration gas mixtures containing at least two gases (usually one of them is a complementary gas) from pure gases or gas pre-mixtures using critical flow orifices systems.The method applies principally to the preparation of mixtures of non-reactive gases that do not react w

47、ith any of the materials forming the gas circuit inside the critical flow orifices system or auxiliary equipment. It has the merit of allowing multi-component mixtures to be prepared as readily as binary mixtures if an appropriate number of critical flow orifices are used.By selecting appropriate co

48、mbinations of critical flow orifices, a dilution ratio of 1 104is achievable.Although it is more particularly applicable to the preparation of gas mixtures at atmospheric pressure, the method also offers the possibility of preparing calibration gas mixtures at pressures greater than atmospheric. The

49、 upstream pressure will need to be at least two times higher than downstream pressure.The range of flow rates covered by this document extends from 1 ml/min to 10 l/min.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 6143, Gas analysis Compa