EN ISO 7053-2011 en Hexagon washer head tapping screws《六角凸缘自攻螺钉》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 7053:2011Hexagon washer head tapping screws (ISO 7053:2011)BS EN ISO 7053:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO

2、 7053:2011. It supersedes BS 7599:1992, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e F M E / 9 / 3 , F a s t e n e r s - P r o d u c t S t a n d a r d s .A list of organizations represented on this committee can be obtained on reques

3、t to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 68780 8 ICS 21.060.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British S

4、tandard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7053 August 2011 ICS 21.060.10 English Version Hexagon washer head tappin

5、g screws (ISO 7053:2011) Vis tle tte hexagonale embase plate (ISO 7053:2011) Sechskant-Blechschrauben mit Bund (ISO 7053:2011) This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givin

6、g this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offic

7、ial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of

8、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

9、EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 7053:2011: EBS EN IS

10、O 7053:2011 EN ISO 7053:2011 (E) 3 Foreword This document (EN ISO 7053:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a n

11、ational standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at the latest by February 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of

12、 patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria

13、, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The

14、 text of ISO 7053:2011 has been approved by CEN as a EN ISO 7053:2011 without any modification. BS EN ISO 7053:2011ISO 7053:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bod

15、ies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

16、 non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,

17、Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies cast

18、ing a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7053 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 13, Fas

19、teners with non-metric thread. This second edition cancels and replaces the first edition (ISO 7053:1992), which has been technically revised. BS EN ISO 7053:2011BS EN ISO 7053:2011INTERNATIONAL STANDARD ISO 7053:2011(E) ISO 2011 All rights reserved 1Hexagon washer head tapping screws 1 Scope This I

20、nternational Standard specifies hexagon washer head tapping screws with thread sizes from ST 2,2 to ST 8 inclusive. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refe

21、rences, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 1478, Tapping screws thread ISO 2702, Heat-treated steel tapping screws Mechanical properties ISO 3269, Fasteners Acce

22、ptance inspection ISO 3506-4, Mechanical properties of corrosion-resistant stainless steel fasteners Part 4: Tapping screws ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 8992, Fasteners General requ

23、irements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners BS EN ISO 7053:2011ISO 7053:2011(E) 2 ISO 2011 All rights reserved3 Dimensions See Figure 1 and Table 1. Symbols an

24、d descriptions of dimensions are specified in ISO 225. a) Type C b) Type F c) Type R aOptional indentation. bDimension a shall be measured at the core diameter of the first full thread. Figure 1 Hexagon washer head tapping screws BS EN ISO 7053:2011ISO 7053:2011(E) ISO 2011 All rights reserved 3Tabl

25、e 1 Dimensions Dimensions in millimetres Thread ST 2,2 ST 2,9 ST 3,5 ST 3,9 ST 4,2 ST 4,8 ST 5,5 ST 6,3 ST 8 Pa0,8 1,1 1,3 1,3 1,4 1,6 1,8 1,8 2,1 a max. 0,8 1,1 1,3 1,3 1,4 1,6 1,8 1,8 2,1 c min. 0,25 0,40 0,60 0,60 0,80 0,90 1,00 1,00 1,20 damax. 2,8 3,5 4,1 4,6 4,9 5,6 6,3 7,3 9,2 max. 4,2 6,3 8,

26、3 8,3 8,8 10,5 11,0 13,5 18,0 dcmin. 3,8 5,8 7,6 7,6 8,1 9,8 10,0 12,2 16,7 nom. = max. 3,00 4,00 5,50 5,50 7,00 8,00 8,00 10,00 13,00 s min. 2,86 3,82 5,32 5,32 6,78 7,78 7,78 9,78 12,73 e min. 3,20 4,28 5,96 5,96 7,59 8,71 8,71 10,95 14,26 nom. = max. 2,0 2,8 3,4 3,4 4,1 4,3 5,4 5,9 7,0 k min. 1,7

27、 2,5 3,0 3,0 3,6 3,8 4,8 5,3 6,4 kwmin. 0,9 1,3 1,5 1,5 1,8 2,2 2,7 3,1 3,3 r min. 0,3 0,4 0,5 0,5 0,6 0,7 0,8 0,9 1,1 r2max. 0,15 0,20 0,25 0,25 0,30 0,30 0,40 0,50 0,60 Type C 2,0 2,6 3,2 3,5 3,7 4,3 5,0 6,0 7,5 Type F 1,6 2,1 2,5 2,7 2,8 3,2 3,6 3,6 4,2 y ref. Type R 2,7 3,0 3,2 3,6 4,3 5,0 6,3 l

28、bType C and Type R Type F nom. min. max. min. max. Approximate mass, in kilograms per 1 000 pieces ( = 7,85 kg/dm3) (for information only) 4,5 3,7 5,3 3,7 4,5 0,17 6,5 5,7 7,3 5,7 6,5 0,21 0,43 0,93 9,5 8,7 10,3 8,7 9,5 0,27 0,54 1,10 1,14 1,84 2,48 13 12,2 13,8 12,2 13,0 0,35 0,66 1,28 1,35 2,09 2,

29、80 3,64 5,44 16 15,2 16,8 15,2 16,0 0,41 0,77 1,44 1,54 2,31 3,10 4,01 5,96 10,90 19 18,2 19,8 18,2 19,0 0,47 0,87 1,59 1,73 2,52 3,39 4,40 6,49 11,80 22 21,2 22,8 20,7 22,0 1,74 1,93 2,74 3,68 4,78 7,01 12,70 25 24,2 25,8 23,7 25,0 2,12 2,95 3,97 5,17 7,54 13,60 32 30,7 33,3 30,7 32,0 4,66 6,06 8,7

30、6 15,70 38 36,7 39,3 36,7 38,0 6,82 9,82 17,50 45 43,7 46,3 43,5 45,0 11,10 19,60 50 48,7 51,3 48,5 50,0 12,00 21,10 NOTE Preferred lengths are those between the continuous, bold, stepped lines. aP = pitch of the thread. bSizes with lengths marked with a dash () cannot be manufactured. BS EN ISO 705

31、3:2011ISO 7053:2011(E) 4 ISO 2011 All rights reserved4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standards Material Steel, in accordance with ISO 2702 Stainless steel General requirements ISO 8992 Thread ISO 1478 Steel grade/

32、 hardness class A2-20H, A4-20H, A5-20H Mechanical propertyInternational Standard ISO 2702 ISO 3506-4 Product grade A Tolerances International Standard ISO 4759-1 As processed Finish Coating Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc

33、flake coatings are specified in ISO 10683. Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Requirements for passivation are specified in ISO 16048. Acceptability Acceptance inspection is specified ISO 3269. 5 Designation EXAMPLE 1 A hexag

34、on washer head tapping screw with thread size ST 3,5, nominal length l = 16 mm, made of steel (St) in accordance with ISO 2702 and rounded end (Type R) is designated as follows: Tapping screw ISO 7053 - ST 3,5 16 - St - R EXAMPLE 2 Designation of a hexagon washer head tapping screw with thread size

35、ST 3,5, nominal length l = 16 mm, made of stainless steel (A4-20H) in accordance with ISO 3506-4 and rounded end (Type R) is designated as follows: Tapping screw ISO 7053 - ST 3,5 16 - A4-20H - R BS EN ISO 7053:2011This page deliberately left blankThis page deliberately left blankBSI is the independ

36、ent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards wor

37、ldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the

38、quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44

39、(0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using

40、 acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply

41、the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Ema

42、il: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase pric

43、eof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI web

44、site at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitte

45、d in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: