EN ISO 7083-1994 en Technical Drawings - Symbols for Geometrical Tolerancing - Proportions and Dimensions《技术制图 几何形位公差的符号 比例和尺寸(ISO 7083-1983)》.pdf

1、CEN EN*IS0*7083 94 m 3404589 OL09782 b55 m BRITISH STANDARD Technical drawings - Symbols for geometrical tolerancing Proportions and dimensions The European Standard EN IS0 7083 : 1994 has the status of a British Standard BS EN IS0 7083 : 1995 BS 308 : Section 3.6 : 1995 CEN EN*IS0*7083 94 3404589 0

2、109783 591 BS EN IS0 7083 : 1995 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TDW4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas pic British S

3、tan Generalities, definitions, s yrnbols. indicetion on drawings. 1 ) symbols for tolerance characteristics and additional IS0 3098/1, Technical drawings - lettering - Part 1 : symbols (see IS0 1101) are always to be depicted as shown Currently used characters. - in figures 1 to 21. li Ar present at

4、 the stage of draft. (Revisiion of ISO/A 1101/1-1969.) CEN EN*ISO*083 74 3404589 0307789 TOT Page 4 EN IS0 7083 : 1994 Figure 1 - Straightness Figure 5 - Profile of any line Figure 2 - Flatness Figure 4 - Cylindricity Figure 6 - Profile of any surface CEN EN*ISO*7083 94 3404589 0307790 721 = Page 5

5、EN IS0 7083 : 1994 Figure 7 - Parallelism Figure 8 - Perpendicularity Figure 9 - Angularity Figure 11 - Concentricity and coaxiality Figure 12 - Symmetry CEN EN*ISO*083 94 3404589 0309793 bb8 W Page 6 EN IS0 7083 : 1994 Figure 13 - Simple runout f Figure 14 - Total runout Figure 15 - Indication of t

6、oleranced feature (by reference letter) Figure 16 - Indication of datum (direct) _ CEN EN*ISO*7083 94 3404589 0309792 5T4 Page 7 EN IS0 7083 : 1994 I_ D Figure 18 - Datum target (IS0 5459) - CEN EN*IS0*7083 94 3404589 O309793 430 Page 8 EN IS0 7083 : 1994 b) a) Figure 19 - Theoretically exact dimens

7、ion a) Figure 20 - Projected tolerance zone a) Figure 21 - Maximum material condition CEN EN*IS0*703 94 3404589 OL09794 377 9 Page 9 EN IS0 7083 : 1994 Characteristic Recommended dimensions Heightof frame(H)* 5 7 10 14 a) 28 40 Height of characters (h) 2.5 3,5 5 7 10 14 20 Diameter D) * 10 14 a) 28

8、405 80 Thickness of line id) 0,25 0.35 0.5 0.7 1 1,4 2 L 5 Dimensions 5.1 Recommended dimensions of the symbols with lettering type A are specified in table 1, those for use with lettering type B in table 2. Table 1 - Lettering type A Dimensions in millimetres Height of characters (h) Diameter 10 *

9、14x1 m4o 5680 Thickness of line d) 0.25 0.35 0.5 0.7 1.4 5.2 The recommended widths of the frame should be : - first compartment, equal to height of frame (HI; - tion; second compartment, to suit the length of the inscrip- - the width of the reference letter (or lettercl. third and subsequent compar

10、tments, if required, to suit The distances between the vertical strokes of the compart- ments and the inscriptions shall be at least twice the thickness of lines, with a minimum of 0,7 mrn. CEN EN*IS0*7083 94 m 3404589 0109795 203 Page 10 EN IS0 7083 : 1994 6 Examples Figure Pa) - Lettering B, verti

11、cal CEN EN*ISO*7083 94 = 3404589 0309796 L4T Page 11 EN IS0 7083 : 1994 Figure 23a) - Lettering 8. vertical CEN EN*IS0*7083 94 = 3404589 0309797 O86 BS EN IS0 7083 : 1995 List of references See national foreword. BS EN IS0 7083 : 1995 BS 308 Section 3.6 : 1995 BSI 389 Chiswick High Road London w4 4A

12、L 951G74.3513- RTL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the intedonal level. It is incorporated by Royal Charter. Contract requirements A British Standard does not p

13、urport to include aU the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. An

14、y person who finds an inaccuracy or ambiguity while using this British Standard should bring it to the attention of the Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unl

15、ess otherwise requested. Information on standards BSI provides a wide range of infodon on national, European and international standards through its fibmy, the Standardline Database, the BSI Infodon Technology Service (BITS) and its Technical Help to Exporters Service. Contact the Information Depart

16、ment at Chiswick Tel 0181 996 7111; Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel: O181

17、 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standard of necessary detais such as symbols and size,

18、type or grade designahons including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of BSI must be obtained and if granted will be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager at Chiswick. ISBN O O80 23776 1 Product code 00583794 TDW4