1、 STDmBSI BS EN IS0 8737-ENGL 1798 H 1ibZLib67 Ob78653 b77 H BRITISH STANDARD Grooved pins - Full-length parallel grooved, with pilot * * m The European Standard EN IS0 8739 : 1997 has the status of a British Standard ICs 21.060.50 BS EN IS0 5739 : 1998 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PER
2、MITTED BY COPYRIGHT LAW - STD*BSI BS EN IS0 8737-ENGL 1778 Lb211bb7 Ob7Ab5LI 503 9 AmdNo. Date BS EN IS0 8739 : 1998 Textaffected National foreword This British Standard is the English language version of EN IS0 8739 : 1997. It is identical with Is0 8739 : 1997. It supemedes ES EN 28739 : 1992 which
3、 is withdram The UKparticipation in its prepamtion was entrusted by Technical Commiaee FME4, Bolts, nuts and accessorieS, to Subcommittee FME/9/6, General purpose fasteners and accessories, which has the responsibility to: - aid enquirers to undad the text; - presenttotheresponsibeinocommiaeeanyenqu
4、ines on the interpretation, or proposals for change, and keep the UK interesls informed; - monitor related intemationai and European developments and promulgate themintheuK. A iist of organbtions represented on this Subcommittee can be obtained on request toit9secretary. Cross-references Attention i
5、s drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to intemationai publications with their corresponding European publicalions ?he British Stan- which implement intemationai or European publicalions refd to in this document may be found in t
6、he BSI standards catalogue under the section entitled Intedonai standards Correspondence Index, or by using the Find tcility of the BSI Stan- Electronic catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a
7、 front cover, an inside front cover, the EN Is0 title page, the EN Is0 foreword page, the Is0 title page, page ii, pages 1 to 3, the annex ZA page, an inside back cover and a back cover. This British standard, having been prepared under the direciion of the Engineering sector Board, was pubiished un
8、der the authority of the standards Board and comes into effect on 16 May 1998 8 BSI 1998 iSBN O 680 29401 3 STD.BSI BS EN IS0 8737-ENGL 1998 1b24bb9 Ob98b55 4LIT EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 8739 November 1997 ICs 21 .o60 Descriptors: see IS0 document Supersedes EN 28739:
9、1992 English version Grooved pins - Full-length parallel grooved, with pilot (IS0 8739: 1 997) Goupilles canneles cannelures constantes sur toute la langueur d8bouchante8, B bout pilote (IC0 8739:1997) Zylinderkerbstie mit Einihrende (IS0 873W997) This European Standard was approved by CEN on 17 Oct
10、ober 1997. CEN members are bound to comply with the CENICENELEC Intemal Regulations whkh stipulate the condltions for giving ails European Standard lhe status oi a national standard withait any aiteration. Uplo-dale lists and bibhographimi references concerning such national standards may be OMSined
11、 on application to lhe Central Secretariat or to any CEN member. This urnpeen Standard exists in three oWcial versions (English, French, German). A version in any other language made by translation under the responsibiily oi a CEN member into its own language and notified to lhe Centrai Secreiariai
12、has lhe same status as lhe otricial versions. CEN members are lhe national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzeiiend and United Kingdom. EUROPEAN COMM
13、ITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FOR NORMUNG COMITE EUROPEEN DE NORMALISATION Central Secretariat rue de Stassart, 36 8-1050 Bru8seis Q 1997 CEN Ail rights of exploitation in any form and by any means reserved worklwide for CEN national Members. Ref. No. EN IS0 8739:1997 E STDmBSI BS EN
14、 IS0 8739-ENGL 1998 lb2Libb9 Ob98b5b 38b W EN IS0 8739 : 1997 The text of the International Standard IS0 8739:1997 has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories“ , the
15、 secretariat of which is held by DIN. This European Standard supersedes EN 28739: 1992. This European Standard shall be given the status of a national Standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdr
16、awn at the latest by May 1998. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemb
17、ourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 8739:1997 was approved by CEN as a European Standard without any modification. NOTE: Normative references to International Standards are listed in ann
18、ex ZA (normative). 4 UI 4 _L_- _ . STD-BSI BS EN IS0 8739-ENGL 1798 = Lb29bb7 Ob78b57 212 M EN IS0 8739 : 1997 INTERNATIONAL STANDARD IS0 0739 Second edition 1997-1 1-01 Grooved pins - Full-length parallel grooved, with pilot Goupilles canneles cannelures constantes sur toute la longueur dbouchantes
19、, bout pilote Reference number IS0 8739: 1 997( E) - 7 STD-BSI BS EN IS0 8739-ENGL 1778 lb24bb9 Ob98b56 159 EN IS0 8739 : 1997 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing Intematio
20、nal Standards is normally carried out through Is0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non- governmental, in liaison with IS
21、O, also take pari in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Int
22、ernational Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 8739 was prepared by Technical Committee ISOTTC 2, Fastenem. This second edition cancels and replaces the first edition (IS0 8739:1986), which has been technically revised. Descrlpt
23、ws: fasteners, steel products, pins (mediani), grooved pins, specifications, charaCterlstiCS, dhnensbs, dedgnatim. i - STD-BSI BS EN IS0 8737-ENGL 2998 W Lb24bb7 ObAb57 075 = EN IS0 8739 : 1997 Grooved pins - Full-length parallel grooved, with pilot 1 scope This International Standard specifies the
24、characteristics of full-length parallel grooved pins, made of steel or austenitic stainless steel, with pilot which have three equally spaced grooves impressed longitudinally on their exterior surface and a pilot to facilitate insertion, with nominal diameter, d, from 1,5 mm to 25 mm inclusive. The
25、displaced material to each side of the grooves forming an expanded diameter d2 which is larger than the nominal diameter d, will cause a non-positive locking fit when these grooved pins are forced into a drilled hole equal to the nominal diameter d, (see clause 4). 2 Normative references The followi
26、ng standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encour
27、aged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 3269: 1988, fasteners - Acceptance inspection. IS0 3506-1:1997, Corrosion-resistant stainless steel fas
28、teners - Part I: Bolts, screws and studs. IS0 4042:-“, fasteners - Electroplated coatings. - s - II = E - * UI * IS0 8749:1986, Pins and grooved pins - Shear test. IS0 9717:1990, Phosphate conversion coatings for metals - Method of specifying requirements. 3 Dimensions See figure 1 and table 1. 1) C
29、hamfer permissible. 2) The grooving angle 70“ applies only to grooved pins made from steel as shown in clause 5. The grooving angle may be modified depending on resilience of material. figure 1 1) To be published. (Revision of IS0 4042:1989) 1 TaMe 1 - Dimensions Dimensions in millimetres 4 nom. 1,s
30、 2 2,s 3 45 6 8 10 12 16 20 25 tol. h9 hll +0,05 O nom. min. max. 8 7.75 8,25 10 9.75 10,25 12 11,5 12,5 14 13.5 145 1,6 16 15,5 l6,5 18 17,5 18,s 20 18.5 20.5 22 21.5 22,5 - 24 23.5 24.5 26 25,5 26,5 28 27,5 283 30 29.5 30.5 32 31.5 32.5 35 34.5 35.5 40 39.5 40.5 45 44.5 45.5 50 493 50,5 55 54.25 5
31、5,76 60 59.25 60.75 65 64.25 85.76 70 69,25 70,75 75 74,25 7575 80 78,25 80,75 85 84.25 85.75 90 89.25 90,75 2,65 - 1) Applies only to grooved pins made from steel as shown in clause 5. 2) The range of commercial lengths is between the stepped lines. I to. 1 20,5 25.5 3) The expanded diameter 4 appl
32、ies only to pins made from steel as shown in clause 5. For other materials, for example stainless steel, a reduction amount shall be subtracted from the given values and should be agreed between customer and supplier. 4) For testhg d, a GONO GO ring gauge should be used. 2 * * v, STD.BS1 BS EN IS0 8
33、739-ENGL 1998 U Lb24bb7 Ob78bbL 743 U EN IS0 8739 : 1997 4 Application The diameter of the hole into which the groove pin is to be inserted shall be equal to the nominal diameter d, of the mating pin and to tolerance class H11. 5 Requirements and reference International Standards See table 2. Table
34、2 - Requirements and reference International Standards Material” Grooves Swface finish Workmanship Shear strength test Accepta hili I Austenitic stainless steel Steel (St) Al in accordance with IS0 3506-1, hardness 210 HV30 to 280 HV30 I Hardness 125 HV30 to 245 HV30 Form of groove at the discretion
35、 of the supplier Plain, .e. pins to be supplied in natural finish treated with a protective lubricant, unless othennrise specified by agreement between customer and supplier. Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conver- sion coating (see IS0 9717 and IS
36、0 4042). Other coatings as agreed between customer and supplier. All tolerances shall apply prior to the applica- tion of a plating or coating. Plain, .e. pins to be supplied in natural finish. Pins shall free of irregularities or detrimental defects. I The test shall be in accordance with IS0 8749.
37、 The acceptance procedure is covered in IS0 3269. 1) Other materials as agreed between customer and supplier. 6 Designation EXAMPLE 1 A full-length parallel grooved steel pin with pilot with nominal diameter d, = 6 mm and nominal length i = 50 mm is designated as follows: Grooved pin IS0 8739 - 6 x
38、50 - St EXAMPLE 2 A full-length parallel grooved austenitic stainless steel pin of grade AI with pilot, with nominal diameter d, = 6 mm and nominal length 1 = 50 mrn is designated as follows: Grooved pin IS0 8739 - 6 x 50 - Al 3 STD.BS1 BS EN IS0 8739-ENGL 1998 m lb2iibb Ob98bb2 b8T m EN IS0 8739 :
39、1997 Annex ZA (normative) Normative references to intemathal publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references cited at the appropriate places in the text and the pu
40、blications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publicati
41、on Year Title IS0 8749 1986 Pins and grooved pins - Shear test EN 28749 1992 BS EN IS0 8739 : 1998 BSI 3 Fax 0181 996 7400. BSI offers members an individual updating service died PLUS which ensures that subscnbers automatically receive the latest editions of standards. Buying standards orders for ai
42、l BSI, inlmnational and foreign standads publications should be addressed to Customer Services, Sales Department at Chiswick Tek 0181 996 7000, Fax 0181 996 7001. in response to ordem for international standards, it is ES1 policy to supply the BSI implementation of the that have been published as Br
43、itish Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Daabase, the BSI information Technology Service (BllS) and its Technical Help to exporte Service. Con
44、tact the Infomation Department at Chiswick Tel: 0181 996 7111; Fax 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantiai discounts on the purchase price of stanards. For detaiis of these and other benents contact Customer Services, Membersh
45、ip at Chiswick Tel: 0181 996 7002, Fax 0181 996 7001. Copyright Copyright subsists in ali BSI publications. BSI also holds the copyright, in the UK, of the publications of the intemational staneon boies. Except as permiaed under the copyright, Designs and Patents Act 1988 no extract may be reproduce
46、d, stored in aretsiaal system ormmmed * in any form or by any means - electroNc, photocopying, recording or otherwise - without prior written pennission from BSL This does not preclude the free use, m the course of implementing the standard, of nec- details such as symbols, and size, type or grade d
47、esignations. if these details are to be used for any other purpose than implementation then the prior wrien pennission of BSI must be obtained if pennission is granted, the tenns may include royalty payments or a licensing agreemenL Details and advice can be obtained hm the Copyright Manager? BSI, 389 Chiswick High Road, London W4 4AL
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1