EN ISO 9455-13-2017 en Soft soldering fluxes - Test methods - Part 13 Determination of flux spattering.pdf

1、Soft soldering fluxes - Test methodsPart 13: Determination of flux spattering (ISO 9455-13:2017)BS EN ISO 9455-13:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9455-13 September 2017 ICS 25.160.50 Superse

2、des EN ISO 9455-13:1999English Version Soft soldering fluxes - Test methods - Part 13: Determination of flux spattering (ISO 9455-13:2017) Flux de brasage tendre - Mthodes dessai - Partie 13: Dtermination des projections de flux (ISO 9455-13:2017) Flussmittel zum Weichlten - Prfverfahren - Teil 13:

3、Bestimmung von Flussmittelspritzern (ISO 9455-13:2017) This European Standard was approved by CEN on 12 September 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without

4、 any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other lan

5、guage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denma

6、rk, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN CO

7、MMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9455-13:2017 ENatio

8、nal forewordThis British Standard is the UK implementation of EN ISO 9455-13:2017. It is identical to ISO 9455-13:2017. It supersedes BS EN ISO 9455-13:2000, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/27, Tin, tin alloys, Solders and soldering

9、 fluxes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BS

10、I Standards Limited 2017ISBN 978 0 580 92646 4ICS 25.160.50Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since pub

11、licationDate Text affected BRITISH STANDARDBS EN ISO 945513:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9455-13 September 2017 ICS 25.160.50 Supersedes EN ISO 9455-13:1999English Version Soft soldering fluxes - Test methods - Part 13: Determination of flux spattering (ISO 9455-13:20

12、17) Flux de brasage tendre - Mthodes dessai - Partie 13: Dtermination des projections de flux (ISO 9455-13:2017) Flussmittel zum Weichlten - Prfverfahren - Teil 13: Bestimmung von Flussmittelspritzern (ISO 9455-13:2017) This European Standard was approved by CEN on 12 September 2017. CEN members are

13、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

14、he CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Cen

15、tre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

16、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix

17、17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9455-13:2017 EBS EN ISO 945513:2017EN ISO 9455-13:2017 (E) 3 European foreword This document (EN ISO 9455-13:2017) has been prepared by Technical Committe

18、e ISO/TC 44 “Welding and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsemen

19、t, at the latest by March 2018, and conflicting national standards shall be withdrawn at the latest by March 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such p

20、atent rights. This document supersedes EN ISO 9455-13:1999. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

21、 Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice

22、The text of ISO 9455-13:2017 has been approved by CEN as EN ISO 9455-13:2017 without any modification. ISO 9455-13:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Principle 15 Apparatus . 16 Procedure. 27 Expression of the results 28 Test report . 3 ISO 2017 All rig

23、hts reserved iiiContents PageBS EN ISO 945513:2017ISO 9455-13:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Principle 15 Apparatus . 16 Procedure. 27 Expression of the results 28 Test report . 3 ISO 2017 All rights reserved iiiContents PageBS EN ISO 945513:2017ISO

24、 9455-13:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subjec

25、t for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

26、 on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be not

27、ed. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifyi

28、ng any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenien

29、ce of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technica

30、l Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 12, Soldering materials.This second edition cancels and replaces the first edition (ISO 9455-13:1996), which

31、has been technically revised.The main changes to the previous version are: solder designations have been updated according to ISO 9453; the test report has been updated; editorial revisions have been made.A list of all parts in the ISO 9455 series can be found on the ISO website.Requests for officia

32、l interpretations of any aspect of this document should be directed to the Secretariat of ISO/TC 44/SC 12 via your national standards body. A complete listing of these bodies can be found at www .iso .org.iv ISO 2017 All rights reservedBS EN ISO 945513:2017ISO 9455-13:2017(E)ForewordISO (the Interna

33、tional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has be

34、en established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stan

35、dardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accorda

36、nce with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Detail

37、s of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an e

38、ndorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the follow

39、ing URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 12, Soldering materials.This second edition cancels and replaces the first edition (ISO 9455-13:1996), which has been technically revised.The main ch

40、anges to the previous version are: solder designations have been updated according to ISO 9453; the test report has been updated; editorial revisions have been made.A list of all parts in the ISO 9455 series can be found on the ISO website.Requests for official interpretations of any aspect of this

41、document should be directed to the Secretariat of ISO/TC 44/SC 12 via your national standards body. A complete listing of these bodies can be found at www .iso .org.iv ISO 2017 All rights reserved INTERNATIONAL STANDARD ISO 9455-13:2017(E)Soft soldering fluxes Test methods Part 13: Determination of

42、flux spattering1 ScopeThis document specifies a method for estimating the tendency of a flux to spatter in use. It is a qualitative (comparative) method and is only applicable to liquid fluxes, as defined in ISO 9454-1.The method is not applicable to flux cored solder wire or to solder pastes.2 Norm

43、ative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any am

44、endments) applies.ISO 3574, Cold-reduced carbon steel sheet of commercial and drawing qualitiesISO 9453, Soft solder alloys Chemical compositions and formsISO 9454-1, Soft soldering fluxes Classification and requirements Part 1: Classification, labelling and packaging3 Terms and definitionsNo terms

45、and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp IEC Electropedia: available at h t t p :/ www .electropedia .org/ 4 PrincipleA mea

46、sured amount of the liquid flux under test is placed on a specimen plate of sheet steel. The plate is heated on a solder bath and the plate examined visually for evidence of spattering of the flux.5 ApparatusUsual laboratory apparatus and, in particular, the following.5.1 Solder bath, of rectangular

47、 cross-section, approximately 150 mm 100 mm, containing at least 4 kg of tin-base solder according to ISO 9453. The depth of the solder shall be such that the liquid surface of the solder is not greater than 5 mm from the bath rim. The bath shall be capable of being maintained at a temperature of (4

48、00 10) C. ISO 2017 All rights reserved 1BS EN ISO 945513:2017ISO 9455-13:2017(E)5.2 Specimen plates, cut from 1 mm thick unalloyed steel sheet, deep drawing quality, according to ISO 3574. The plates are to be cut to size, such that the length and width are 10 mm larger than the corresponding dimens

49、ions of the solder bath (5.1).5.3 Silicon carbide cloth, 180 grade.6 ProcedureAdjust the temperature of the solder in the solder bath (5.1) to (400 10) C. Ensure that the level of the solder in the bath is (4 1) mm below the level of the rim of the bath.Carry out the following procedure on three specimen plates (5.2).Using the silicon carbide cloth (5.3), clean the surface of each specimen plate immediately before testing in order to remove all oxidation and contamination from the steel.By means of a fine gradua