EN ISO 10350-1-2017 en Plastics - Acquisition and presentation of comparable single-point data - Part 1 Moulding materials.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics - Acquisition and presentation of comparable single-point dataPart 1: Moulding materialsBS EN ISO 103501:2017National forewordThis British Standard is the UK implementation of EN ISO 103501:2017. It is identica

2、l to ISO 103501:2017. It supersedes BS EN ISO 103501:2008+A1:2014, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/21, Testing of plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This public

3、ation does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 92755 3ICS 83.080.20; 83.080.01Compliance with a British Standard cannot confe

4、r immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 103501:2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE

5、NORMEN ISO 10350-1November 2017ICS 83.080.20 Supersedes EN ISO 103501:2008, EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN Ref. No. EN ISO 103501:2017: EAll rights of exploita

6、tion in any form and by any means reserved worldwide for CEN national MembersPlastics Acquisition and presentation of comparable singlepoint data Part 1: Moulding materials (ISO 103501:2017)Plastiques Acquisition et prsentation de caractristiques intrinsques comparables Partie 1: Matriaux pour moula

7、ge (ISO 103501:2017)Kunststoffe Ermittlung und Darstellung vergleichbarer Einpunktkennwerte Teil 1: Formmassen (ISO 103501:2017)This European Standard was approved by CEN on 10 September 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

8、 giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three off

9、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of

10、 Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia,

11、 Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 10350-1:2017 (E)European forewordThis document (EN ISO 103501:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is h

12、eld by NBN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be withdrawn at the latest May 2018.Attention is drawn to the possibility that some of

13、 the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN ISO 103501:2008.According to the CENCENELEC Internal Regulations, the national standards organizations of the following coun

14、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Po

15、land, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 103501:2017 has been approved by CEN as EN ISO 103501:2017 without any modification.2BS EN ISO 103501:2017ISO 10350-1:2017(E)Foreword ivIntroduction v1 Sco

16、pe . 12 Normative references 13 Terms and definitions . 34 Specimen preparation and conditioning. 35 Test requirements . 46 Presentation of results . 4Bibliography .14 ISO 2017 All rights reserved iiiContents PageBS EN ISO 103501:2017ISO 10350-1:2017(E)ForewordISO (the International Organization for

17、 Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the

18、right to be represented on that committee. International organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedur

19、es used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial r

20、ules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights iden

21、tified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation

22、on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/forew

23、ord.html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical behavior.This third edition cancels and replaces the second edition (ISO 103501:2007), which has been technically revised. It also incorporates the Amendment ISO 103501:2007/Amd.1:2014.A lis

24、t of all parts in the ISO 10350 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 103501:2017ISO 10350-1:2017(E)IntroductionThe ISO 10350 series has been prepared because users of plastics find that available data cannot always be readily used to compare the properties

25、of similar materials, especially when the data have been supplied by different sources. Even when the same standard tests have been used, they often allow the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily comparable. The purpose of this document i

26、s to identify specific methods and conditions of test to be used for the acquisition and presentation of data in order that valid comparisons between materials can be made.The ISO 10350 series is concerned with tests employed to present “singlepoint” data on the limited range of properties commonly

27、included in data sheets and used for the preliminary selection of materials. Such data represent the most basic approach to the specification of properties of materials, and the ISO 10350 series thus facilitates the first steps towards more efficient selection and use of plastics in the many applica

28、tions to which they are suited.Complementary International Standards (ISO 114031, ISO 114032 and ISO 114033) are concerned with the standardized acquisition and presentation of multipoint data, to demonstrate how properties vary with important factors such as time, temperature and the presence of pa

29、rticular natural and chemical environments. In these documents, some additional properties are included. Their use will provide a more substantial database than one containing only singlepoint data, and so will enable improved assessment of the fitness of a material for any particular application. I

30、n addition, ISO 11403-1, which deals with mechanical properties, assists predictions of the performance of components and ISO 11403-2, covering thermal and processing properties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3 is concerned with environmental influences on p

31、roperties, and other parts may be prepared to cover additional properties. ISO 2017 All rights reserved vBS EN ISO 103501:2017This page deliberately left blankPlastics - Acquisition and presentation of comparable single-point data Part 1: Moulding materials1 ScopeThe ISO 10350 series identifies spec

32、ific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. T

33、he properties included are those presented conventionally in manufacturers data sheets. This document applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection or compressionmoulded or prepared as sheets of specified thickness. For the purpo

34、ses of this document, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.2 Normative referencesThe following documents are referred to in the text in such a w

35、ay that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 62, Plastics Determination of water absorptionISO 751, Pl

36、astics Determination of temperature of deflection under load Part 1: General test methodISO 752, Plastics Determination of temperature of deflection under load Part 2: Plastics and eboniteISO 178, Plastics Determination of flexural propertiesISO 1791, Plastics Determination of Charpy impact properti

37、es Part 1: Non-instrumented impact testISO 1792, Plastics Determination of Charpy impact properties Part 2: Instrumented impact testISO 293, Plastics Compression moulding of test specimens of thermoplastic materialsISO 2941, Plastics Injection moulding of test specimens of thermoplastic materials Pa

38、rt 1: General principles, and moulding of multipurpose and bar test specimensISO 2943, Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small platesISO 2944, Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shr

39、inkageISO 295, Plastics Compression moulding of test specimens of thermosetting materialsISO 306, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST)ISO 5271, Plastics Determination of tensile properties Part 1: General principlesINTERNATIONAL STANDARD ISO 10350-1:201

40、7(E) ISO 2017 All rights reserved 1BS EN ISO 103501:2017ISO 10350-1:2017(E)ISO 5272, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plasticsISO 8991, Plastics Determination of creep behaviour Part 1: Tensile creepISO 11331, Plastics Determination of t

41、he melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard methodISO 11332, Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moistur

42、eISO 11831, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration methodISO 11832, Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column methodISO 11833, Plastics Methods

43、for determining the density of non-cellular plastics Part 3: Gas pyknometer methodISO 2577, Plastics Thermosetting moulding materials Determination of shrinkageISO 2818, Plastics Preparation of test specimens by machiningISO 3915, Plastics Measurement of resistivity of conductive plasticsISO 45892,

44、Plastics Determination of burning behaviour by oxygen index Part 2: Ambient-temperature testISO 66032, Plastics Determination of puncture impact behaviour of rigid plastics Part 2: Instrumented impact testingISO 8256, Plastics Determination of tensile-impact strengthISO 107241, Plastics Injection mo

45、ulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 1: General principles and moulding of multipurpose test specimensISO 107242, Plastics Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 2: Small platesISO 113572, Plastics Differ

46、ential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step heightISO 113573, Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallizationISO 113592, Plastics Thermomechanical a

47、nalysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperatureISO 20753,1)Plastics Test specimensIEC 60112, Method for the determination of the proof and the comparative tracking indices of solid insulating materialsIEC 602431, Electrical strength of

48、insulating materials Test methods Part 1: Tests at power frequenciesIEC 60250, Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths1) ISO 20753 specifies th

49、e designations and dimensions of test specimens used for the acquisition of comparable data, and also other frequently used specimens, in one document for ease of reference. It is intended to gradually replace ISO 3167.2 ISO 2017 All rights reservedBS EN ISO 103501:2017ISO 10350-1:2017(E)IEC 60296, Fluids for electrotechnical applications Unused mineral insulating oils for tr