EN ISO 10510-2011 en Tapping screw and washer assemblies with plain washers《带普通垫圈的自攻螺钉和垫圈组件》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 10510:2011Tapping screw and washerassemblies with plain washersBS EN ISO 10510:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of E

2、N ISO10510:2011. It supersedes BS EN ISO 10510:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication

3、does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 71500 6ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

4、of theStandards Policy and Strategy Committee on 30 April 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10510 April 2011 ICS 21.060.10 Supersedes EN ISO 10510:1999English Version Tapping screw and washer assemblies with plain washe

5、rs (ISO 10510:2011) Vis tle rondelle plate imperdable (ISO 10510:2011) Kombi-Blechschrauben mit flachen Scheiben (ISO 10510:2011) This European Standard was approved by CEN on 17 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions fo

6、r giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in thre

7、e official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bod

8、ies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Ki

9、ngdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10510:2011: E

10、BS EN ISO 10510:2011EN ISO 10510:2011 (E) 3 Foreword This document (EN ISO 10510:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the sta

11、tus of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the su

12、bject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10510:1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implemen

13、t this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switze

14、rland and the United Kingdom. Endorsement notice The text of ISO 10510:2011 has been approved by CEN as a EN ISO 10510:2011 without any modification. BS EN ISO 10510:2011ISO 10510:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide

15、 federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that

16、committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in acc

17、ordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requ

18、ires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10510 was prepared by Technic

19、al Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners. This second edition cancels and replaces the first edition (ISO 10510:1999), of which it constitutes a minor revision. BS EN ISO 10510:2011BS EN ISO 10510:2011INTERNATIONAL STANDARD ISO 10510:2011(E) ISO 2011 All

20、rights reserved 1Tapping screw and washer assemblies with plain washers 1 Scope This International Standard specifies the requirements for tapping screws and plain washer assemblies with thread sizes from ST2,2 to ST9,5 inclusive, flat seating heads and mechanical properties as specified in ISO 2702

21、. The plain washers are captive, i.e. prevented from disassembly and free to rotate. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of t

22、he referenced document (including any amendments) applies. ISO 1478, Tapping screws thread ISO 1479, Hexagon head tapping screws ISO 1481, Slotted pan head tapping screws ISO 2702, Heat-treated steel tapping screws Mechanical properties ISO 6507-1, Metallic materials Vickers hardness test Part 1: Te

23、st method ISO 7049, Cross-recessed pan head tapping screws ISO 10669, Plain washers for tapping screw and washer assemblies Normal and large series Product grade A 3 Dimensions The dimensions of the assembled screws shall conform to the designated product standards for loose parts with the following

24、 exceptions: screws shall have a shank of such diameter, ds, that the washer with dimensions in accordance with ISO 10669 is free to rotate; the permitted distance from the underside of the head to the first full thread shall be increased by the maximum thickness of the washer as specified in ISO 10

25、669; the transition diameter, da, shall be reduced by the difference between the nominal and thread rolling diameter. For the dimensions, see Figures 1 to 4 and Table 1. BS EN ISO 10510:2011ISO 10510:2011(E) 2 ISO 2011 All rights reservedFigure 1 Hexagon head tapping screw, for example with cone end

26、 (type C) Figure 2 Cross-recessed pan head tapping screw, for example with flat end (type F) Figure 3 Slotted pan head tapping screw, for example with rounded end (type R) Figure 4 Transition diameter, da, and shank diameter, ds BS EN ISO 10510:2011ISO 10510:2011(E) ISO 2011 All rights reserved 3Tab

27、le 1 Dimensions Dimensions in millimetres Washer dimensionsaNormal series Type N Large series Type L Thread size ab max. damax. h nom. d2max. h nom. d2max. ST2,2 ST2,9 ST3,5 0,8 1,1 1,3 2,1 2,8 3,3 1 1 1 5 7 8 1 1 1 7 9 11 ST4,2 ST4,8 ST5,5 1,4 1,6 1,8 4,03 4,54 5,22 1 1 1,6 9 10 12 1 1,6 1,6 12 15

28、15 ST6,3 ST8 ST9,5 1,8 2,1 2,1 5,93 7,76 9,43 1,6 1,6 2,0 14 16 20 1,6 2 2,5 18 24 30 aDimensions extracted from ISO 10669, for information only. bDimension a measured after assembly, with washer in contact with the screw bearing face or underhead radius.4 Specifications and reference standards The

29、mechanical properties of the screw component of the tapping screw and washer assembly shall be those specified in ISO 2702. Following assembly and heat treatment, the washer component shall have a hardness of 90 HV to 320 HV. Vickers hardness testing shall be carried out in accordance with ISO 6507-

30、1. Test force: HV 10 for nominal thickness h u 1,2 mm Test force: HV 30 for nominal thickness h 1,2 mm Prior to assembly, suitable precautions shall be taken to prevent detrimental case hardening of the washer during heat treatment, e.g. copper plating. 5 Designation The designation of a tapping scr

31、ew and washer assembly shall consist of: a) the description of the components; b) the reference to this International Standard, i.e. ISO 10510; c) the thread size and nominal length of the tapping screw; d) the type of thread end in accordance with ISO 1478; e) the screw symbol specifying the type o

32、f screw (see Table 2); f) the washer symbol specifying the type of washer (see Table 3). BS EN ISO 10510:2011ISO 10510:2011(E) 4 ISO 2011 All rights reservedTable 2 Symbols for the screws Reference International Standard Symbol ISO 1479 Hexagon head tapping screws S1 ISO 7049 Cross recessed pan head

33、 tapping screws S2 ISO 1481 Slotted pan head tapping screws S3 Table 3 Symbols for the washers Reference International Standard Type of washer Symbol Normal N ISO 10669 Plain washers for tapping screw and washer assemblies Large L EXAMPLE 1 A hexagon head tapping screw and washer assembly with a scr

34、ew size of ST4,2 16, with rounded end (R) in accordance with ISO 1478, screw type in accordance with ISO 1479 (symbol S1), and a plain washer, normal series, in accordance with ISO 10669 (symbol N) is designated as follows: Tapping screw and washer assembly ISO 10510 ST4,2 16 R S1 N EXAMPLE 2 A cros

35、s-recessed pan head tapping screw and washer assembly with a screw size of ST 4,2 16, with rounded end (R) in accordance with ISO 1478, screw type with cross recess type Z in accordance with ISO 7049 (symbol S2) and a plain washer, normal series, according to ISO 10669 (symbol N) is designated as fo

36、llows: Tapping screw and washer assembly ISO 10510 ST4,2 16 R Z S2 N BS EN ISO 10510:2011This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and service

37、s. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are up

38、dated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this Briti

39、sh Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically recei

40、ve the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationsc

41、an be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standa

42、rdsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +4

43、4 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (

44、0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the internat

45、ional standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This

46、does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: