EN ISO 10579-2013 en Geometrical product specifications (GPS) - Dimensioning and tolerancing - Non-rigid parts《几何产品技术规范(GPS) 尺寸标注和公差 非刚性部件》.pdf

1、BSI Standards PublicationBS ISO 10579:2010Geometrical productspecifications (GPS) Dimensioning and tolerancing Non-rigid partsBS EN ISO 10579:2013BS EN ISO 10579:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 10579:2013. It is identical to ISO 10579:20

2、10. It supersedes BS ISO 10579:2010, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purpor

3、t to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 81091 6ICS 01.100.20Compliance with a British Standard cannot confer immunity from legal obligatio

4、ns.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2010.Amendments/corrigenda issued since publicationDate Text affected30 September 2013 This corrigendum renumbers BS ISO 10579:2010 as BS EN ISO 10579:2013EUROPEAN STANDARD NORME EURO

5、PENNE EUROPISCHE NORM EN ISO 10579 July 2013 ICS 01.100.20 English Version Geometrical product specifications (GPS) - Dimensioning and tolerancing - Non-rigid parts (ISO 10579:2010 including Cor 1:2011) Spcification gomtrique des produits (GPS) - Cotation et tolrancement - Pices non rigides (ISO 105

6、79:2010, Cor 1:2011 inclus) Geometrische Produktspezifikation (GPS) - Bemaung und Tolerierung - Nicht-formstabile Teile (ISO 10579:2010 + Cor 1:2011) This European Standard was approved by CEN on 11 July 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

7、the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standa

8、rd exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the natio

9、nal standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slov

10、akia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved w

11、orldwide for CEN national Members. Ref. No. EN ISO 10579:2013: EiiBS EN ISO 10579:2013EN ISO 10579:2013 (E)EN ISO 10579:2013 (E) 3 Foreword The text of ISO 10579:2010 including Cor 1:2011 has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and veri

12、fication” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 10579:2013 by Technical Committee CEN/TC 290 “Dimensional and ge ometrical pr oduct s pecification and verification” the s ecretariat of w hich is he ld by AFNOR. This European Standard shall be g

13、iven the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility that some of the elements of this document m

14、ay be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austri

15、a, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

16、 Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10579:2010 including Cor 1:2011 has been approved by CEN as a EN ISO 10579:2013 without any modification. BS ISO 10579:2010ISO 10579:2010(E) iv ISO 2010 All rights reservedIntroduction This International Standard is a ge

17、ometrical product specification (GPS) standard and is to be regarded as a global GPS standard (see ISO/TR 14638)4. It influences chain links 1, 2 and 3 of the chain of standards on form of line independent of datum, form of line dependent on datum, form of surface independent of datum, form of surfa

18、ce dependent on datum, orientation, location, circular run-out and total run-out in the general GPS matrix. For more detailed information on the relation of this standard to other standards and the GPS matrix model, see Annex B. Certain parts, when removed from their manufacturing environment, may d

19、eform significantly from their defined limits owing to their weight, flexibility or the release of internal stresses resulting from the manufacturing processes. These parts are defined as “non-rigid parts” and the deformation is acceptable provided that the parts may be brought within the indicated

20、tolerance by applying reasonable force to facilitate inspection and assembly. Depending on the design function and the parts interface with its mating components, instead of, or in addition to, assessing the part conventionally (in its free state condition), it may be necessary to assess the part wh

21、en subject to restraint that is no greater than those accepted in the assembled condition. Parts in this category include both those of inherently rigid material (such as thin metal parts) and those of inherently flexible material (such as rubber, plastics, etc.). BS EN ISO 10579:2013ISO 10579:2010

22、(E) ISO 2010 All rights reserved iiiThis page deliberately left blankBS ISO 10579:2010INTERNATIONAL STANDARD ISO 10579:2010(E) ISO 2010 All rights reserved 1Geometrical product specifications (GPS) Dimensioning and tolerancing Non-rigid parts 1 Scope This International Standard gives rules for dimen

23、sioning and tolerancing non-rigid parts where restraining of features is required during verification of dimensions and tolerances specified on a drawing. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

24、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1101:2004, Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out 3 Terms and definitions For the purpo

25、ses of this document, the following terms and definitions apply. 3.1 non-rigid part part which deforms to an extent that in the free state is beyond the dimensional and/or geometrical tolerances on the drawing 3.2 free state condition of a part subjected only to the force of gravity 4 Basic principl

26、es The distortion of a non-rigid part must not exceed that which allows the part to be brought within specified tolerances for verification and positioning at assembly, or assembled, by applying pressure or forces not exceeding those which can be expected under normal assembly conditions. It is impo

27、ssible to avoid the effect of natural forces such as gravity, but the extent of distortion may depend upon the orientation of the part and condition of the part in the free state. If it is necessary to indicate the tolerance in the free state, the conditions under which the tolerance is to be achiev

28、ed (i.e. the direction of gravity, conditions in which it is to be supported, etc.) may have to be indicated in a note, as shown in Annex A. For non-rigid parts, identified on the drawing by the added statement “ISO 10579-NR”, the restrained condition applies unless the dimensions and tolerances are

29、 qualified by the symbol , see Clause 5. BS EN ISO 10579:2013BS ISO 10579:2010ISO 10579:2010(E) 2 ISO 2010 All rights reserved5 Indications on drawings Drawings of non-rigid parts shall include the following indications as appropriate (see also Annex A): a) in or near the title block, the indication

30、 “ISO 10579-NR”; b) in a note, the conditions under which the part shall be restrained to meet the drawing requirements; c) geometrical tolerances allowed in the free state, with the modifying symbol included in the tolerance frame in accordance with ISO 1101; d) dimensional tolerances allowed in th

31、e free state, with the modifying symbol after the dimensional tolerance; e) the conditions under which the geometrical tolerance under free state is achieved, such as direction of gravity, orientation of the part, etc. BS EN ISO 10579:2013ISO 10579:2010 (E)BS ISO 10579:2010ISO 10579:2010(E) ISO 2010

32、 All rights reserved 3Annex A (informative) Examples of indication and interpretation Indication on the drawing Interpretation ISO 10579-NR Restrained condition: The surface indicated as datum A is mounted (with 64 bolts M6 tightened to a torque of 9 Nm to 15 Nm) and the feature indicated as datum B

33、 is restrained at the corresponding mating size. The geometrical and dimensional tolerance, followed by the symbol , shall be ensured in the free state. Other tolerances apply under the conditions indicated in the note.Indication on the drawing Interpretation ISO 10579-NR Key 1 direction of gravity

34、Restrained condition: The surface indicated as surface A is mounted (with 120 bolts M20 tightened to a torque of 18 Nm to 20 Nm) and the feature indicated as surface B is restrained at the corresponding mating size. The geometrical tolerance, followed by the symbol , shall be ensured in the free sta

35、te. Other tolerances apply under the conditions indicated in the note. BS EN ISO 10579:2013ISO 10579:2010 (E)BS ISO 10579:2010ISO 10579:2010(E) 4 ISO 2010 All rights reservedAnnex B (informative) Relation to the GPS matrix model B.1 General For full details about the GPS matrix model, see ISO/TR 146

36、384. B.2 Information about this standard and its use This International Standard gives rules for dimensioning and tolerancing non-rigid parts where restraining of features is required during verification of dimensions and tolerances specified on a drawing. B.3 Position in the GPS matrix model This I

37、nternational Standard is a geometrical product specification (GPS) standard and is to be regarded as a global GPS standard (see ISO/TR 14638). It influences chain links 1, 2 and 3 of the chain of standards on form of line independent of datum, form of line dependent on datum, form of surface indepen

38、dent of datum, form of surface dependent on datum, orientation, location, circular run-out and total run-out in the general GPS matrix, as graphically illustrated in Figure B.1. Global GPS standards General GPS standards Chain link number 1 2 3 4 5 6 Size Distance Radius Angle Form of line independe

39、nt of datum X X X Form of line dependent on datum X X X Form of surface independent of datum X X X Form of surface dependent on datum X X X Orientation X X X Location X X X Circular run-out X X X Total run-out X X X Datums Roughness profile Waviness profile Primary profile Surface imperfections Fund

40、amental GPS standards Edges Figure B.1 Position in the GPS matrix model BS EN ISO 10579:2013ISO 10579:2010 (E)BS ISO 10579:2010ISO 10579:2010(E) ISO 2010 All rights reserved 5B.4 Related standards The related standards are those of the chains of standards indicated in Figure B.1. BS EN ISO 10579:201

41、3ISO 10579:2010 (E)BS ISO 10579:2010ISO 10579:2010(E) 6 ISO 2010 All rights reservedBibliography 1 ISO 2692:2006, Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) 2 ISO 5458:1998, G

42、eometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing 3 ISO 5459:1981, Geometrical product specifications (GPS) Geometrical tolerancing Datums and datum-systems 4 ISO/TR 14638, Geometrical product specification (GPS) Masterplan BS EN ISO 10579:2013ISO 10579:2010 (E)B

43、S ISO 10579:2010BS EN ISO 10579:2013BS ISO 10579:2010ISO 10579:2010(E) ICS 01.100.20 Price based on 6 pages ISO 2010 All rights reserved BS EN ISO 10579:2013ISO 10579:2010 (E)This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-rel

44、ated publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together busi

45、ness, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations o

46、f all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Kn

47、owledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Developm

48、ent Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to

49、over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service ex