EN ISO 10619-1-2018 en Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 1 Bending tests at ambient temperature.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Rubber and plastics hoses and tubing Measurement of flexibility and stiffnessPart 1: Bending tests at ambient temperature (ISO 10619-1:2017)BS EN ISO 10619-1:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO

2、10619-1 March 2018 ICS 23.040.70 Supersedes EN ISO 10619-1:2011English Version Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 1: Bending tests at ambient temperature (ISO 10619-1:2017) Tuyaux et tubes en caoutchouc et en plastique - Mesurage de la flexibilit e

3、t de la rigidit - Partie 1: Essais de courbure temprature ambiante (ISO 10619-1:2017) Gummi- und Kunststoffschluche mit und ohne Einlage - Bestimmung der Biegsamkeit und Steifigkeit - Teil 1: Biegeprfungen bei Umgebungstemperatur (ISO 10619-1:2017) This European Standard was approved by CEN on 20 Ja

4、nuary 2018. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be o

5、btained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

6、 CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irel

7、and, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Manage

8、ment Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10619-1:2018 ENational forewordThis British Standard is the UK implementation of EN ISO 106191:2018. It is identical to ISO

9、 106191:2017. It supersedes BS EN ISO 106191:2011, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this committee can be obtained on request to its sec

10、retary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96982 9ICS 23.040.70Compliance with a British Standard canno

11、t confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 106191:2018EUROPEAN STANDARD NORME EUROPENNE EURO

12、PISCHE NORM EN ISO 10619-1 March 2018 ICS 23.040.70 Supersedes EN ISO 10619-1:2011English Version Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 1: Bending tests at ambient temperature (ISO 10619-1:2017) Tuyaux et tubes en caoutchouc et en plastique - Mesurage

13、 de la flexibilit et de la rigidit - Partie 1: Essais de courbure temprature ambiante (ISO 10619-1:2017) Gummi- und Kunststoffschluche mit und ohne Einlage - Bestimmung der Biegsamkeit und Steifigkeit - Teil 1: Biegeprfungen bei Umgebungstemperatur (ISO 10619-1:2017) This European Standard was appro

14、ved by CEN on 20 January 2018. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

15、 standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language

16、and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hun

17、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG

18、 CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10619-1:2018 EBS EN ISO 106191:2018EN ISO 10619-1:2018 (E) 3 European foreword This document (EN ISO 106

19、19-1:2018) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national stan

20、dard, either by publication of an identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall be withdrawn at the latest by August 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

21、CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10619-1:2011. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Be

22、lgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Swed

23、en, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10619-1:2017 has been approved by CEN as EN ISO 10619-1:2018 without any modification. BS EN ISO 106191:2018ISO 10619-1:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 24 Method A1 24.1

24、Apparatus 24.2 Hose test pieces 24.2.1 Types and dimensions 24.2.2 Number 34.3 Conditioning of hose test pieces 34.4 Test temperatures 34.5 Test procedure . 34.6 Expression of results 34.7 Test report . 35 Method A2 45.1 Apparatus 45.2 Hose test pieces 45.2.1 Types and dimensions 45.2.2 Number 45.3

25、Conditioning of hose test pieces 45.4 Test temperatures 45.5 Test procedure . 45.6 Test report . 56 Method B . 56.1 Apparatus 56.2 Hose test piece 56.3 Test temperatures 56.4 Procedure 66.5 Test report . 67 Method C1 67.1 Apparatus 67.2 Hose test piece 67.3 Test temperature . 67.4 Procedure 67.5 Tes

26、t report . 78 Method C2 78.1 Apparatus 78.2 Hose test piece 78.3 Test temperature . 78.4 Procedure 78.5 Expression of results 88.6 Test report . 8 ISO 2017 All rights reserved iiiContents PageBS EN ISO 106191:2018ISO 10619-1:2017(E)ForewordISO (the International Organization for Standardization) is

27、a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represent

28、ed on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop t

29、his document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC

30、Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the de

31、velopment of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nat

32、ure of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This docume

33、nt was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This second edition cancels and replaces the first edition (ISO 10619-1:2011), of which it constitutes a minor revision. The changes compared to the previous

34、 edition are as follows: the unit used in the formula to calculate the flexural stiffness in 8.4 and 8.5 has been changed.A list of all parts in the ISO 10619- series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 106191:2018INTERNATIONAL STANDARD ISO 10619-1:2017(E)Rubber

35、and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperatureWARNING Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its

36、 use. It is the responsibility of the user to establish appropriate safety and health practices.1 ScopeThis document specifies three methods for measuring the flexibility of rubber and plastics hoses and tubing (methods A1, B and C1), where the deformation of the hose or tubing is measured, and two

37、methods for measuring the stiffness (methods A2 and C2) by measuring the force required to bend rubber or plastics hoses or tubing to a specific radius at ambient temperature.Methods A1 and A2 are suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 80 mm.Met

38、hod A1 allows the measurement of the flexibility of the hose or tubing by measuring the reduction in outside diameter when the hose is compressed between two plates.Method A2 provides a means of measuring the force required to reach a specific bend radius when the hose or tubing is compressed, as be

39、tween two plates. The test can be carried out at a specified internal pressure.Method B is suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 100 mm, and provides a means of assessing the behaviour of the hose and tubing when bent around a mandrel. The fina

40、l mandrel diameter used can be taken as the minimum bend radius of the hose or tubing. As this value is determined by the reduction of the outside diameter, it can be used as a measure of the flexibility of the hose or tubing. The hose or tubing being tested can be unpressurized, pressurized or unde

41、r vacuum and, if required, with the curvature or against the curvature of the hose or tubing, if such curvature is present.Methods C1 and C2 are suitable for rubber and plastics hoses and tubing with inside diameter of 100 mm and greater.Method C1 provides a means of determining the flexibility of t

42、he hose and tubing at the minimum bend radius.Method C2 provides a method of measuring the stiffness of the hose and tubing at the minimum bend radius.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of

43、 this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of

44、hose assembliesISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary ISO 2017 All rights reserved 1BS EN ISO 106191:2018ISO 10619-1:2017(E)ISO 23529, Rubber General procedures for preparing and conditioning test pieces for physical test methods3 Terms and definitionsFor the purposes of

45、this document, the terms and definitions given in ISO 8330 and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.

46、org/obp3.1bendingshaping or forcing something straight into a curve or angle at a specified temperature3.2flexibilityease of bending (3.1) a hose without it being damaged by kinking, collapse, breaking or crackingNote 1 to entry: A hose can be bent around a mandrel, for example.3.3stiffnessresistanc

47、e of a hose to bending (3.1)3.4hose deformationovality obtained when a hose is compressed or bent (3.1) around a mandrelNote 1 to entry: This may be measured by the reduction in the outside or inside diameter.3.5flexural stiffnessmeasure of the resistance of a hose to bending (3.1)3.6dynamometerforc

48、e measuring device4 Method A14.1 ApparatusThe apparatus shall consist of two guides, A and B, guide A being fixed in a plane and guide B being movable in that plane, parallel to and in line with, guide A see Figure 1a).If it is desired to measure the force to attain the specified radius of curvature

49、, this may be done, for example, by means of pulleys and weights. Care shall be taken to minimize the effects of frictional resistance (see Figure 2).4.2 Hose test pieces4.2.1 Types and dimensionsThe hose test pieces shall consist either of complete manufactured lengths of hose or suitable test lengths. If the manufactured length is shorter than the length required for the test, hose test pieces of adequate length shall be specially manufactured.2 ISO 2017 All rights reservedBS EN ISO 106191:2018ISO 10619-1:2017(E)4.