EN ISO 11148-10-2011 en Hand-held non-electric power tools - Safety requirements - Part 10 Compression power tools《非电动手持工具 安全要求 第10部分 压缩电动工具》.pdf

1、BSI Standards PublicationBS EN ISO 11148-10:2011Hand-held non-electric power tools Safety requirementsPart 10: Compression power tools (ISO 11148-10:2011)Incorporating corrigendum August 2015BS EN ISO 11148-10:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN

2、 ISO 11148-10:2011. It supersedes BS EN 792-10:2000 + A1:2008,which will be withdrawn 30 June 2012.The UK participation in its preparation was entrusted by Technical Committee MCE/8, Compressors, pneumatic tools, pneumatic machinesA list of organizations represented on this subcommittee can be obtai

3、ned on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. ISBN 978 0 580 91496 6 ICS 25.140.10 Compliance with a British Standard cannot confer im

4、munity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dPublished by BSI Standards Limited 2015 30 September 2015 Implementation o

5、f ISO corrected text 15 April2012non-electric power tools - Safety.and vacuum technology, to Subcommittee MCE/8/-/2, Hand-held, The ISO corrected text 15 April 2012 incorporates the following editorial corrections:a) the seventh figure, which was a repeat of Figure B.1 (squeeze riveter), was deleted

6、 from page 18; b) the titles of Figure B.5 (crimping tool) and Figure B.6 (cutter) have been correctly repositioned immediately below their respective figures at the bottom of page 17.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11148-10 December 2011 ICS 25.140.10 Supersedes EN 792-10:2

7、000+A1:2008English Version Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools (ISO 11148-10:2011) Machines portatives moteur non lectrique - Exigences de scurit - Partie 10: Machines portatives compression (ISO 11148-10:2011) Handgehaltene nicht elektrische b

8、etriebene Maschinen - Sicherheitsanforderungen - Teil 10: Maschinen zum Pressen (ISO 11148-10:2011) This European Standard was approved by CEN on 12 November 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa

9、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English,

10、 French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulg

11、aria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR

12、 STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11148-10:2011: EForeword This document (EN

13、 ISO 11148-10:2011) has been prepared by Technical Committee ISO/TC 118 “Compressors and pneumatic tools, machines and equipment“ in collaboration with Technical Committee CEN/TC 255 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS. This European Standard shall

14、be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may

15、 be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 792-10:2000+A1:2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Assoc

16、iation, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imple

17、ment this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swi

18、tzerland and the United Kingdom. Endorsement notice The text of ISO 11148-10:2011 has been approved by CEN as a EN ISO 11148-10:2011 without any modification. BS EN ISO 11148-10:2011 EN ISO 11148-10:2011 (E)ii ISO 2011 All rights reservedAnnex ZA (informative) Relationship between this European Stan

19、dard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC

20、on machinery. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the clauses of this standard confers, within the limits of the scope of this standard, a presumpt

21、ion of conformity with the corresponding Essential Requirements of that Directive except ER 1.5.7 and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 11148-10:2011 EN ISO 11148-10

22、:2011 (E) ISO 2011 All rights reserved iiiReference numberISO 11148-10:2011(E)ISO 2011INTERNATIONAL STANDARD ISO11148-10First edition2011-12-01Corrected version2012-04-15Hand-held non-electric power tools Safety requirements Part 10: Compression power tools Machines portatives moteur non lectrique E

23、xigences de scurit Partie 10: Machines portatives compression COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,

24、without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland BS EN ISO 11148

25、-10:2011 EN ISO 11148-10:2011 (E) ISO 2011 All rights reserved v Contents Page Foreword iv Introduction . v 1 Scope 1 2 Normative references 2 3 Terms and definitions . 2 3.1 General terms and definitions 2 3.2 Terms and definitions related to compression power tools . 4 4 Safety requirements and/or

26、 protective measures 5 4.1 General . 5 4.2 Mechanical safety 5 4.3 Thermal safety . 5 4.4 Noise reduction . 5 4.5 Vibration . 6 4.6 Materials and substances processed, used or exhausted 7 4.7 Ergonomics 7 4.8 Controls 7 5 Verification . 8 5.1 General conditions for tests . 8 5.2 Noise . 8 5.3 Vibrat

27、ion . 8 5.4 Unintentional start . 8 5.5 Power tool construction . 8 5.6 Structure of verification 9 6 Information for use 9 6.1 Marking, signs and written warnings 9 6.2 Instruction handbook 10 6.3 Operating instructions 14 6.4 Data . 14 6.5 Maintenance instructions . 15 Annex A (informative) List o

28、f significant hazards . 16 Annex B (informative) Examples of compression power tools covered by this part of ISO 11148 17 Annex C (normative) Symbols for labels and signs 18 Bibliography 19 BS EN ISO 11148-10:2011 EN ISO 11148-10:2011 (E) ISO 2011 All rights reservedvi Foreword ISO (the Internationa

29、l Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been es

30、tablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardi

31、zation. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for vot

32、ing. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all suc

33、h patent rights. ISO 11148-10 was prepared by Technical Committee ISO/TC 118, Compressors and pneumatic tools, machines and equipment, Subcommittee SC 3, Pneumatic tools and machines. This corrected version of ISO 11148-10:2011 incorporates the following corrections in Annex B: a) the seventh figure

34、, which was a repeat of Figure B.1 (squeeze riveter), was deleted from page 18; b) the titles of Figure B.5 (crimping tool) and Figure B.6 (cutter) have been correctly repositioned immediately below their respective figures at the bottom of page 17. ISO 11148 consists of the following parts, under t

35、he general title Hand-held non-electric power tools Safety requirements: Part 1: Assembly power tools for non-threaded mechanical fasteners Part 2: Cutting-off and crimping power tools Part 3: Drills and tappers Part 4: Non-rotary percussive power tools Part 5: Rotary percussive drills Part 6: Assem

36、bly power tools for threaded fasteners Part 7: Grinders Part 8: Sanders and polishers Part 9: Die grinders Part 10: Compression power tools Part 11: Nibblers and shears Part 12: Circular, oscillating and reciprocating saws A part 13, dealing with fastener driving tools, is under preparation. BS EN I

37、SO 11148-10:2011 EN ISO 11148-10:2011 (E) ISO 2011 All rights reserved viiIntroduction This document is a type-C standard as stated in ISO 12100. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are defined in the Scope of this part of ISO 11148. W

38、hen requirements of this type-C standard are different from those which are stated in type-A or -B standards, the requirements of this type-C standard take precedence over the requirements of other standards, for machines that have been designed and built according to the requirements of this type-C

39、 standard. ISO 11148 consists of a number of independent parts for individual types of hand-held non-electric power tools. Certain parts of ISO 11148 cover hand-held non-electric power tools driven by internal combustion engines powered by gaseous or liquid fuel. In these parts, the safety aspects r

40、elating to internal combustion engines are found in a normative annex. The parts are type-C standards and refer to pertinent Standards of type A and B where such standards are applicable. BS EN ISO 11148-10:2011 EN ISO 11148-10:2011 (E) ISO 2011 All rights reservedviii INTERNATIONAL STANDARD ISO 111

41、48-10:2011(E) ISO 2011 All rights reserved 1Hand-held non-electric power tools Safety requirements Part 10: Compression power tools IMPORTANT The colours represented in the electronic file of this document can be neither viewed on screen nor printed as true representations. For the purposes of colou

42、r matching, see ISO 3864-4, which provides colorimetric and photometric properties together with, as a guideline, references from colour order systems. 1 Scope This part of ISO 11148 specifies safety requirements for hand-held non-electric compression power tools (hereinafter “compression power tool

43、s”) intended for squeeze riveting, punching, shaping, pressing and cutting of metal, plastics and other materials. The compression power tools can be powered by compressed air or hydraulic fluid and are intended to be used by one operator and supported by the operators hand or hands, with or without

44、 a suspension, e.g. a balancer. NOTE 1 At the time of publication, no compression power tools driven by internal combustion engines are known. Once these are identified, it is intended to amend this part of ISO 11148 to include such power tools. This part of ISO 11148 is applicable to: crimping tool

45、s; collar splitters; power tools for metal forming (edge formers, folding tools, swagers); nut splitter heads; presses; punches; squeeze riveters; cutting power tools with parallel knives; alligator jaw compression riveters. NOTE 2 For examples of compression power tools, see Annex B. This part of I

46、SO 11148 is not applicable to special requirements and modifications of compression power tools for the purpose of mounting them in a fixture. This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events relevant to compression power tools when they are used as

47、 intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of compression power tools in potentially explosive atmospheres. NOTE 3 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres. BS EN

48、 ISO 11148-10:2011ISO 11148-10:2011(E) 2 ISO 2011 All rights reserved2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3857-3, Compressors, pneumatic tools and machines Vocabulary Part 3: Pneumatic tools and machines ISO 5391, Pneumatic tools and machines Vocabulary ISO 12100:2010, Safety of machinery