1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11298-3:2011Plastics piping systems for r e n o v a t i o n o f u n d e r g r o u n d water supply networksPart 3: Lining with close-fit pipes (ISO 11298-3:2010)BS EN I
2、SO 11298-3:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 11298-3:2011. It is identical to ISO 11298-3:2010. It supersedes BS EN 14409-3:2004, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e
3、 e P R I / 8 8 / 3 , R e h a b i l i t a t i o n o f p i p e l i n e s y s t e m s using plastics piping materials and components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provision
4、s of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 72269 1 ICS 23.040.20; 23.040.45; 93.025 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and St
5、rategy Committee on 31 May 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11298-3 April 2011 ICS 23.040.20; 23.040.45; 93.025 Supersedes EN 14409-3:2004English Version Plastics piping systems for renovation of underground
6、water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2010) Systmes de canalisations en plastique pour la rnovation des rseaux enterrs dalimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11298-3:2010) Kunststoff-Rohrleitungssysteme fr die Renovieru
7、ng von erdverlegten Wasserversorgungsnetzen - Teil 3: Close-Fit-Lining (ISO 11298-3:2010) This European Standard was approved by CEN on 8 April 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status
8、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa
9、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia,
10、 Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATI
11、ON COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11298-3:2011: EBS EN ISO 11298-3:2011 EN ISO 11298-3:201
12、1 (E) 3 Foreword The text of ISO 11298-3:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 11298-3:2011 by Technical Committee CEN/TC
13、 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall b
14、e withdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14409-3:2004. A
15、ccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
16、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 11298-3:2010 has been approved by CEN as a EN ISO 11298-3:2011 without any modification. BS EN ISO 1
17、1298-3:2011ISO 11298-3:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 3.1 General .2 3.2 Techniques.2 3.3 Geometrics.2 3.4 Materials .2 3.5 Product stages.2 3.6 Service conditions.2 3.7 Joints 3 4 Symbols a
18、nd abbreviated terms 3 4.1 Symbols3 4.2 Abbreviated terms .4 5 Pipes at the “M” stage 4 5.1 Materials .4 5.2 General characteristics.4 5.3 Material characteristics.4 5.4 Geometric characteristics 5 5.5 Mechanical characteristics.5 5.6 Physical characteristics5 5.7 Jointing.5 5.8 Marking.5 6 Fittings
19、 at the “M” stage.5 7 Ancillary components.6 8 Fitness for purpose of the installed lining system at the “I” stage .6 8.1 Materials .6 8.2 General characteristics.6 8.3 Material characteristics.6 8.4 Geometric characteristics 6 8.5 Mechanical characteristics.7 8.6 Physical characteristics8 8.7 Addit
20、ional characteristics.8 8.8 Sampling.8 9 Installation practice.9 9.1 Preparatory work .9 9.2 Storage, handling and transport9 9.3 Equipment 9 9.4 Installation10 9.5 Process-related inspection and testing 11 Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe Determination of memo
21、ry ability .12 Bibliography14 BS EN ISO 11298-3:2011ISO 11298-3:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normal
22、ly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the
23、 work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare I
24、nternational Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some o
25、f the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11298-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids. ISO 11298 consists of the
26、 following parts, under the general title Plastics piping systems for renovation of underground water supply networks: Part 1: General Part 3: Lining with close-fit pipes Lining with continuous pipes is to form the subject of a part 2; lining with cured-in-place pipes is to form the subject of a par
27、t 4; lining with adhesive-backed hoses is to form the subject of a part 6. BS EN ISO 11298-3:2011ISO 11298-3:2010(E) ISO 2010 All rights reserved vIntroduction This part of ISO 11298 is a part of a System Standard for plastics piping systems of various materials used for the renovation of existing p
28、ipelines in a specified application area. System Standards for renovation deal with the following applications: Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks; Plastics piping systems for renovation of underground water supply networks; Plastics pip
29、ing systems for renovation of underground gas supply networks; Plastics piping systems for renovation of underground drainage and sewerage networks under pressure. These System Standards are distinguished from those for conventionally installed plastics piping systems by the requirement to verify ce
30、rtain characteristics in the as-installed condition, after site processing. This is in addition to specifying requirements for plastics piping systems components as manufactured. This System Standard comprises a: Part 1: General and all applicable renovation technique family-related parts from the f
31、ollowing: Part 2: Lining with continuous pipes Part 3: Lining with close-fit pipes Part 4: Lining with cured-in-place pipes Part 6: Lining with adhesive-backed hoses The requirements for any given renovation technique family are given in part 1, applied in conjunction with the relevant other part. F
32、or example, ISO 11298-1 and this part of ISO 11298 together specify the requirements relating to lining with close-fit pipes. For complementary information, see ISO 11295. Not all technique families are pertinent to every area of application and this is reflected in the part numbers included in each
33、 System Standard. A consistent structure of clause headings has been adopted for all parts of ISO 11298, in order to facilitate direct comparisons across renovation technique families. Figure 1 shows the common part and clause structure and the relationship between ISO 11298 and the System Standards
34、 for other application areas. BS EN ISO 11298-3:2011ISO 11298-3:2010(E) vi ISO 2010 All rights reservedFigure 1 Format of the renovation System Standards BS EN ISO 11298-3:2011INTERNATIONAL STANDARD ISO 11298-3:2010(E) ISO 2010 All rights reserved 1Plastics piping systems for renovation of undergrou
35、nd water supply networks Part 3: Lining with close-fit pipes 1 Scope This part of ISO 11298, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human
36、 consumption, including raw water intake pipelines. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system. 2 Normative references The following referenced documents are
37、indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3126, Plastics piping systems Plastics components Determination of dimensions ISO 44
38、27-1:2007, Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General ISO 4427-2, Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes ISO 4427-3, Plastics piping systems Polyethylene (PE) pipes and fittings for water supply P
39、art 3: Fittings ISO 4427-5:2007, Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system ISO 11298-1:2009, Plastics piping systems for renovation of underground water supply networks Part 1: General ISO 12176-1, Plastics pipes and fitti
40、ngs Equipment for fusion jointing polyethylene systems Part 1: Butt fusion ISO 12176-2, Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 2: Electrofusion EN 12201-4, Plastics piping systems for water supply Polyethylene (PE) Part 4: Valves BS EN ISO 11298-3:2011ISO
41、 11298-3:2010(E) 2 ISO 2010 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 4427-1 and ISO 11298-1 and the following apply. 3.1 General 3.1.1 close fit situation of the outside of the installed liner relative to the inside of the e
42、xisting pipeline, which may either be an interference fit or include a small annular gap resulting from shrinkage and tolerances only 3.1.2 close-fit pipe continuous lining pipe of thermoplastic material reshaped or otherwise expanded after insertion to achieve a close fit to the existing pipeline 3
43、.2 Techniques No additional definitions apply. 3.3 Geometrics 3.3.1 maximum mean outside diameter dem, maxmaximum value of the outside diameter as specified for a given nominal size 3.4 Materials No additional definitions apply. 3.5 Product stages No additional definitions apply. 3.6 Service conditi
44、ons 3.6.1 maximum operating pressure MOP maximum effective pressure of the fluid in the piping system, expressed in bar1), which is allowed in continuous use NOTE 1 It takes into account the physical and the mechanical characteristics of the components of a piping system. NOTE 2 It is calculated usi
45、ng the following equation: ()()()20 MRSPSDR-1C=1) 1 bar = 0,1 MPa = 105Pa; 1 MPa = 1 N/mm2. BS EN ISO 11298-3:2011ISO 11298-3:2010(E) ISO 2010 All rights reserved 33.7 Joints 3.7.1 electrofusion joint joint between a PE socket or saddle electrofusion fitting and a pipe or fitting with spigotted ends
46、, made by heating the electrofusion fittings by the Joule effect of the heating element incorporated at their jointing surfaces, causing the material adjacent to them to melt and pipe and fitting surfaces to fuse 3.7.2 butt fusion joint joint made by heating the planed ends of matching surfaces by h
47、olding them against a flat heating plate until the PE material reaches fusion temperature, quickly removing the heating plate and pushing the two softened ends against one another 3.7.3 mechanical joint joint made by assembling a PE pipe to another PE pipe, or any other element of the piping system
48、that generally includes a compression part, to provide for pressure integrity, leaktightness and resistance to end loads NOTE A support sleeve inserted into the pipe bore can be used to provide a permanent support for the PE pipe to prevent creep in the pipe wall under radial compressive forces. 3.7
49、.4 fusion compatibility ability of two similar or dissimilar PE materials to be fused together to form a joint which conforms to the performance requirements of this part of ISO 11298 4 Symbols and abbreviated terms 4.1 Symbols For the purpose of this document, the symbols given in ISO 11298-1 and the following apply. C overall service (design) coefficient deoutside diameter (at any point) dem, maxmaximum mean outside diameter dmanuforiginal circular outside diameter of the pipe (befo
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1