EN ISO 11542-1-2001 en Plastics - Ultra-High-Molecular-Weight Polythylene (PE-UHMW) Moulding and Extrusion Materials - Part 1 Designation System and Basis for Specifications《塑料 超高分.pdf

1、BRITISH STANDARD Plastics Ultra-high- molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials Part 1 : Designation system and basis for specificat ions The European Standard EN IS0 11542-1:2001 has the status ofa British Standard ICs 83.080.20 BS EN IS0 1 1542- 1 1200 1 Incorporatin

2、g Corrigendum No. I WkN present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations repre

3、sented on this committee can be obtained on request to its secretary. Cr oss-r e fer enc e s Attention is drawn to the fact that CEN and CENELEC Standards normally include an annexe which lists normative references to international publications with their corresponding European publications. The Bri

4、tish Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled Tnternational Standards Correspondence Index”, or by using the Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purp

5、ort to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front c

6、over, the EN IS0 title page, the EN IS0 Foreword page, the IS0 title page, pages ii and iii, a blank page, pages 1 to 7, the Annex ZA page, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 24 January 2002 ISBN

7、 O 580 37864 O EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 11542-1 February 2001 ICs 83.080.20 English version Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1 : Designation system and basis for specifications (IS0 1 1542-1 :2001) P

8、lastiques - Matriaux base de polythylne trs haute masse molculaire (PE-UHMW) pour moulage et extrusion - Partie 1 : Systme de dsignation et base de spcifications (IS0 11542-1:2001) This European Standard was approved by CEN on 15 February 2001 CEN members are bound to comply with the CENKENELEC Inte

9、rnal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.

10、 This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are

11、the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FUR NORMUNG COMI

12、T EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 11542-1:2001 E EN IS0 11542-12001 Foreword The text of the International Standard IS0 1154

13、2-1 :2001 has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics“, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by

14、endorsement, at the latest by August 2001, and conflicting national standards shall be withdrawn at the latest by August 2001. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel

15、gium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 11542-1:2001 was approved by CEN as a European Standar

16、d without any modification. NOTE: Normative references to International Standards are listed in annex ZA (normative). EN IS0 11542-12001 INTERNATIONAL IS0 STANDARD I 1542-1 Second edition 2001-02-15 Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part

17、 1: Designation system and basis for specifications Plasfiques - Mafriaux base de polyfhylne frs haufe masse molculaire (PE-UHMW) pour moulage ef exfrusion - Partie 1: Sysfme de dsignafion ef base de spcificafions Reference number IS0 11542-1:2001(E) EN IS0 11542-12001 t II EN IS0 11542-12001 Forewo

18、rd IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technic

19、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el

20、ectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard require

21、s approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of IS0 11542 may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0

22、1 1542-1 was prepared by Technical Committee ISO/TC 61, Plasfics, Subcommittee SC 9, Thermoplasfic maferials. This second edition cancels and replaces the first edition (IS0 11542-1 :1994), which has been technically revised. The major change is that density has been replaced by Charpy notched impac

23、t strength as one of the designatory properties. IS0 11 542 consists of the following parts, under the general title Plasfics - Ulfra-high-molecular-weighf polyefhylene (PE-UHMW) moulding and exfrusion maferials: - Par 1: Designafion sysfem and basis for specificafions - Par 2: Preparafion of fesf s

24、pecimens and deferminafion of properies . 111 EN IS0 11542-12001 EN IS0 11542-12001 Plastics - UItra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications 1 Scope 1.1 may be used as the basis for specifications. This p

25、art of IS0 11542 establishes a system of designation for PE-UHMW thermoplastic materials which For the purposes of this part of IS0 11542, PE-UHMW materials are polyethylene materials having a melt mass- flow rate (MFR), measured at 190 OC and 21,6 kg load, of less than 0,l g/lO min. 1.2 levels of t

26、he designatory properties The types of PE-UHMW are differentiated from each other by a classification system based on appropriate a) viscosity number b) elongational stress c) Charpy notched impact strength and on information about intended application and/or method of processing, important properti

27、es, additives, colorants, fillers and reinforcing materials. 1.3 This part of IS0 11542 is applicable to all PE-UHMW homopolymers and to ultra-high-molecular-weight copolymers of ethylene having a content of other l-olefinic monomers of less than 50 % by mass and a content of non-olefinic monomers w

28、ith functional groups up to a maximum of 3 % by mass. It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not intended to imply that materials having the same designation give

29、 necessarily the same performance. This part of IS0 11 542 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall

30、 be determined in accordance with the test methods specified in part 2 of this International Standard, if suitable. 1.5 additional requirements may be given in data block 5 (see 3.1). In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, 2 No

31、rmative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IS0 11542. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements base

32、d on this part of IS0 11542 are encouraged to investigate the 1 EN IS0 11542-12001 Description block (opt ionai) possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Memb

33、ers of IS0 and IEC maintain registers of currently valid International Standards. Individual-item block International Standard number block block block block block block IS0 1043-1:-), Plasfics - Symbols and abbreviafed ferms - Par 1: Basic polymers and fheir special characferisfics. IS0 1628-3: 199

34、1, Plasfics - Deferminafion of viscosify number and limifing viscosify number - Par 3: Polyefhylenes and polypropylenes. IS0 5834-1 :I 998, Implanfs for surgery - Ulfra-high molecular weighf polyefhylene - Par 1: Powder form. IS0 1 1542-2:1998, Plasfics - Ulfra-high-molecular-weighf polyefhylene (PE

35、-UHMW) moulding and exfrusion maferials - Par 2: Preparafion of fesf specimens and deferminafion of properies. 3 Designation system 3.1 General The designation system for thermoplastics is based on the following standardized pattern: Designation Identity block I The designation consists of an option

36、al description block, reading ”Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided into five data blocks comprising the following information: - Data block 1: Identification

37、of the plastic by its symbol PE-UHMW in accordance with IS0 1043-1 (see 3.2). - Data block 2: Position 1: Intended application or method of processing (see 3.3). Positions 2 to 8: Important properties, additives and supplementary information (see 3.3). - Data block 3: Designatory properties (see 3.4

38、). - Data block 4: Fillers or reinforcing materials and their nominal content (see 3.5) - Data block 5: For the purpose of specifications, a fifth data block may be added containing additional information (see 3.6). The first character of the individual-item block shall be a hyphen. The data blocks

39、shall be separated from each other by commas. If a data block is not used, this shall be indicated by doubling the separation sign, .e. by two commas (,). 1) To be published. (Revision of IS0 1043-1:1997) 2 EN IS0 11542-12001 Code-letter 3.2 Data block 1 Position 1 Code-letter Positions 2 to 8 A Pro

40、cessing stabilized In this data block, after the hyphen, PE-UHMW plastics are identified by the symbol PE-UHMW, in accordance with IS0 1043-1. C D 3.3 Data block 2 Coloured Powder In this data block, information about intended application and/or method of processing is given in position 1 and inform

41、ation about important properties, additives and colour in positions 2 to 8. The code-letters used are specified in Table 1. E F If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall be inserted in position 1. Extrusion E Expandable Ext

42、rusion of films F Special burning characteristics G General use G Gran u les H Heat aging stabilized K L Metal deactivated Light or weather stabilized M Moulding N Natural (no colour added) Cl Compression moulding R Mould release agent S X 3.4 Data block 3 Sintering S Lubricated No indication X No i

43、ndication 3.4.1 General Y In this data block, the range of the viscosity number is represented by a single-figure code-number (see 3.4.2), the elongational stress by a single-figure code-number (see 3.4.3), and the Charpy notched impact strength by a single-figure code-number (see 3.4.4). The code-n

44、umbers are separated from each other by hyphens. Textile yarns, spinning Y Increased electrical conductivity Z Antistatic 3 EN IS0 11542-12001 Code-number If a property value falls on or near a range limit, the manufacturer shall state which range will designate the material. If subsequent individua

45、l test values lie on, or either side of, the limit because of manufacturing tolerances, the designation is not affected. Range of viscosity number NOTE Not all combinations of the values of the designatory properties may be possible for currently available polymers. 1 2 3.4.2 Viscosity number 1 710

46、but 2190 but2700 The viscosity number shall be determined in accordance with IS0 1628-3, using a nitrogen atmosphere. 3 4 The possible values of viscosity number are divided into six ranges, each represented by a single-figure code- number, as specified in Table 2. Only materials with code-numbers 1

47、 to 5 in Table 2 shall be used if the abrasion resistance of the material is important to the application. 2700 but3400 3400 but 0,l but 0,2 but 0,3 but 0,7 O 4100 3.4.3 Elongational stress The elongational stress shall be determined in accordance with annex A of IS0 11 542-2:1998. The possible valu

48、es of the elongational stress are divided into five ranges, each represented by a single-figure code-number as specified in Table 3. 4 EN IS0 11542-12001 3.4.4 Charpy notched impact strength The Charpy notched impact strength shall be determined in accordance with annex B of IS0 11542-2:1998. The po

49、ssible values of the notched impact strength are divided into three ranges, each represented by a single- figure code-number as specified in Table 4. Table 4 - Ranges of Charpy notched impact strength in data block 3 Range of notched impact strength kJ/m2 Code-num ber 40 but 170 3.5 Data block 4 In this data block, the type of filler and/or reinforcing material is represented by a single code-letter in position 1, and the form is represented by a second code-letter in position 2, the code-letters being as specified in Table 5. Subsequentl