EN ISO 12863-2010 en Standard test method for assessing the ignition propensity of cigarettes (Incorporating Corrigendum February 2011 Incorporates Amendment A1 2016)《标准试验方法评估香烟点燃倾.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 12863:2010Standard test methodfor assessing the ignitionpropensity of cigarettesIncorporating corrigendum February 2011BS EN ISO 12863:2010 BRITISH STANDARDNational for

2、ewordThis British Standard is the UK implementation of EN ISO 12863:2010. It is identical to ISO 12863:2010, incorporating corrigendum February 2011. The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e F S H / 2 1 / 1 5 , R e a c t i o n t o f i r e t e s t s

3、 - Cigarette ignition propensity test.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011ISBN 978 0 580 7

4、4322 1ICS 13.220.40; 65.160 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2010.Amendments/corrigenda issued since publicationDate T e x t a f f e c

5、t e dImplementation of ISO corrigendum February 2011: Modification of Subclause 5.5 and Figure A.531 August 2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 12863 September 2010 ICS 13.220.40; 65.160 English Version Standard test method for assessing the ignition propensity of cigarettes

6、 (ISO 12863:2010) Mthode dessai normalise pour valuer le potentiel incendiaire des cigarettes (ISO 12863:2010) Normprfverfahren zur Beurteilung der Zndneigung von Zigaretten (ISO 12863:2010) This European Standard was approved by CEN on 14 September 2010. CEN members are bound to comply with the CEN

7、/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or t

8、o any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versi

9、ons. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slo

10、venia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN

11、national Members. Ref. No. EN ISO 12863:2010: EIncorporating corrigendum February 20113 Foreword The text of ISO 12863:2010 has been prepared by Technical Committee ISO/TC 92 “Fire safety” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 12863:2010 by Tec

12、hnical Committee CEN/TC 401 “Project Committee - Reduced Ignition Propensity Cigarettes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and co

13、nflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According

14、 to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

15、Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 12863:2010 has been approved by CEN as a EN ISO 12863:2010 without any modification. BS EN ISO 12863:2010EN

16、ISO 12863:2010 (E)iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 General principle .2 5 Apparatus.2 5.1 General description.2 5.2 Test and conditioning environment 2 5.3 Test chamber .3 5.4 Substrate holder 3 5.5 Metal rim.3 5.6 Cigarette ho

17、lder .3 5.7 Cigarette ignition system3 5.8 Exhaust hood.4 6 Verification of test equipment4 6.1 Frequency of verification4 6.2 Examination for chamber leakage .4 6.3 Stability of chamber atmosphere.4 6.4 Humidity and temperature sensors .4 6.5 Test performance verification 5 7 Test specimens and sta

18、ndard substrate assemblies 5 7.1 Handling .5 7.2 Cigarettes .5 7.3 Filter paper .6 8 Conditioning 6 8.1 Cigarettes .6 8.2 Filter paper .6 9 Test procedure.7 10 Test record .8 11 Test report9 Annex A (normative) Technical drawings of test apparatus 10 Annex B (informative) Estimation of placement of

19、additional pins .14 Annex C (normative) Procedure for selection of substrate assemblies for testing 16 Annex D (informative) Repeatability and reproducibility17 Annex E (informative) Ignition susceptibility of substrate assemblies.18 Bibliography19 BS EN ISO 12863:2010EN ISO 12863:2010 (E) ISO 2011i

20、v Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a

21、 technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matte

22、rs of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circula

23、ted to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsibl

24、e for identifying any or all such patent rights. ISO 12863 was prepared by Technical Committee ISO/TC 92, Fire safety, Subcommittee SC 1, Fire initiation and growth. This International Standard is based, with permission from ASTM International, on ASTM International E2187, Standard Test Method for M

25、easuring the Ignition Strength of Cigarettes, copyright ASTM International. BS EN ISO 12863:2010EN ISO 12863:2010 (E) ISO 2011vIntroduction A very common initiating event in a fatal fire is the dropping of a cigarette onto a bed or piece of upholstered furniture. The burning cigarette heats the furn

26、ishing materials to the point where smouldering combustion begins, perhaps followed by a transition to flaming combustion. Since limiting the frequency of ignitions is a principal approach to reducing fire loss, it is desirable to establish a test method for the propensity of a cigarette to ignite s

27、oft furnishings. BS EN ISO 12863:2010EN ISO 12863:2010 (E) ISO 2011BS EN ISO 12863:2010EN ISO 12863:2010 (E) ISO 2011INTERNATIONAL STANDARD1Standard test method for assessing the ignition propensity of cigarettes WARNING This International Standard involves the use of combustible materials that are

28、exposed to ignition sources. The burning materials emit toxic combustion products. The user shall take proper precautions to avoid thermal injury and inhalation of combustion products. The user shall ensure that all burning has ceased before safely discarding test materials. 1 Scope This Internation

29、al Standard provides a standard assessment of the capability of a cigarette, positioned on one of three standard substrates, to extinguish or to generate sufficient heat to continue burning, and thus potentially cause ignition of bedding or upholstered furniture. This International Standard is appli

30、cable to factory-made cigarettes that burn along the length of a tobacco column. This is a performance-based standard; it does not prescribe any design features of the cigarette that might lead to improved or degraded performance in the test method. The output of this method has been correlated with

31、 the potential for cigarettes to ignite upholstered furniture. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document

32、 (including any amendments) applies. ASTM E2187, Standard Test Method for Measuring the Ignition Strength of Cigarettes ISO 8243, Cigarettes Sampling ISO 13943, Fire safety Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 13943 and the foll

33、owing apply. 3.1 determination single measurement involving a lit cigarette placed on a selected substrate 3.2 full-length burn outcome of a determination in which the cigarette continues to burn to or past the front plane of the tipping paper (filter tip cigarettes) or past the tips of the metal pi

34、ns for non-filter tip cigarettes 3.3 no full-length burn outcome of a determination in which the cigarette ceases to burn before reaching the front plane of the tipping paper (filter tip cigarettes) or the tips of the metal pins for non-filter tip cigarettes EN ISO 12863:2010 (E)BS EN ISO 12863:2010

35、 ISO 20112 3.4 substrate (for cigarette testing) horizontal surface consisting of layers of filter paper on which a test cigarette is placed for testing 3.5 test set of 40 determinations 4 General principle This test method measures the probability that a cigarette, placed on a heat absorbing substr

36、ate, will generate sufficient heat to maintain burning of the tobacco column and potentially initiate a fire. Each determination consists of placing a lit cigarette on one of three standard substrates (3, 10, or 15 layers of filter paper). Observation is made of whether or not the cigarette continue

37、s to burn nominally the length of the tobacco column, as defined in this International Standard. Forty determinations (comprising a test) are performed to obtain the relative probability that the cigarette will continue burning despite heat abstraction by the substrate. 5 Apparatus 5.1 General descr

38、iption An apparatus consists of a holder for the filter paper substrate, a metal rim to compress the layers of filter paper, a clear enclosure to protect the test specimens from air currents, and associated accessories, as defined in this clause. The materials of construction shall meet occupational

39、 health and safety requirements. The apparatus shall be placed under a fume hood to minimize the exposure of personnel to combustion products. Technical drawings of the test chamber are provided in Annex A. 5.2 Test and conditioning environment 5.2.1 General Cigarettes and filter paper shall be cond

40、itioned in one of the two ways described in 5.2.2 and 5.2.3. 5.2.2 Conditioning room An environmental conditioning room shall be maintained which provides an area adequate for conditioning both cigarettes and filter paper specimens. This room shall be capable of maintaining a relative humidity of (5

41、5 5) % and a temperature of (23 3) C and shall be continuously monitored. The room in which the tests are conducted, which may also be the conditioning room, shall be maintained within the same temperature and relative humidity ranges. NOTE These conditioning requirements are consistent with those u

42、sed for fire safety testing. Other types of testing can require different conditioning requirements. 5.2.3 Conditioning box Alternatively, cigarettes and filter paper shall be stored in a box of sufficient size to hold the needed quantities of filter paper and cigarettes. The interior of the box sha

43、ll be maintained at the same temperature and relative humidity conditions as in 5.2.2 and shall be continuously monitored. A tray containing a saturated solution of sodium bromide (NaBr) in water will provide the appropriate relative humidity when the box temperature is as prescribed. The box shall

44、be located convenient to the test chamber such that test materials shall not be exposed to a non-conditioned environment for more than 5 min between their removal from the box and the beginning of a determination. BS EN ISO 12863:2010EN ISO 12863:2010 (E) ISO 201135.3 Test chamber A rectangular test

45、 chamber with a chimney that can be placed under an exhaust hood (5.8) shall be constructed of clear, rigid material that allows observation of the entire determination. NOTE Clear polymethylmethacrylate (PMMA) has been found suitable for this purpose. The inside dimensions of the test chamber shall

46、 be: height (340 25) mm, width (292 6) mm and depth (394 6) mm. The full front panel of the chamber shall be hinged, with a latch to effect positive closure. The top of the chamber shall have a flattop cylindrical chimney of height (165 13) mm and inside diameter (152 6) mm. The chimney shall be cen

47、tred on the chamber top and sealed to the chamber top panel. A sheet of rigid material shall be used to cover the chimney when required in the test procedure (Clause 9). The chamber shall be supported on four feet, located near each corner, each approximately 15 mm in height. Technical drawings of t

48、he test chamber are provided in Annex A. 5.4 Substrate holder A cylindrical support for the layers of circular filter paper shall be made of rigid material. NOTE Clear polymethylmethacrylate (PMMA) has been found suitable for this purpose. The outer diameter of the substrate holder shall be (165 1)

49、mm, the inner diameter shall be (127 1) mm, and the height shall be (50 1) mm. A recess in the top, (10 2,5) mm deep, shall expand the inner diameter to (152 1) mm. Three or four legs shall raise the bottom of the holder approximately (20 1) mm above the chamber floor. Technical drawings of the holder are provided in Annex A. 5.5 Metal rim A circular metal rim, made of brass with a density of (8 550 150) kgm3or other, equally dense material shall be used to hold the sheets of filter paper flat against each other. The outside diameter