EN ISO 13102-2012 en Geometrical product specifications (GPS) - Dimensional measuring equipment Electronic digital-indicator gauge - Design and metrological characteristics《产品几何技术规.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 13102:2012Geometrical product specifications (GPS) Dimensional measuring equipment: Electronic digital-indicator gauge Design and metrological characteristicsBS EN ISO

2、13102:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 13102:2012.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e T D W / 4 , T e c h n i c a l P r o d u c t R e a l i z a t i o n .A list of organizations repr

3、esented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 58

4、0 66733 6 ICS 17.040.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2012.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN

5、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13102 August 2012 ICS 17.040.30 English Version Geometrical product specifications (GPS) - Dimensional measuring equipment: Electronic digital-indicator gauge - Design and metrological characteristics (ISO 13102:2012) Spcification gomtrique des produi

6、ts (GPS) - Instruments de mesurage dimensionnel: Comparateurs tige rentrante affichage numrique - Caractristiques de conception et caractristiques mtrologiques (ISO 13102:2012) Geometrische Produktspezifikation und -prfung (GPS) - Lngenmessgerte - Konstruktionsmerkmale und messtechnische Merkmale fr

7、 elektronische digitale Messuhren (ISO/FDIS 13102:2012) This European Standard was approved by CEN on 20 July 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any

8、 alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other languag

9、e made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark,

10、Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR

11、STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13102:2012: EBS EN ISO 13102:2012EN ISO 131

12、02:2012 (E) 3 Foreword This document (EN ISO 13102:2012) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification”

13、, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2013, and conflicting national standards shall be withdrawn at the latest by February 2013. At

14、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations

15、of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

16、therlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 13102:2012 has been approved by CEN as a EN ISO 13102:2012 without any modification. BS EN ISO 13102:2012ISO 13102:2012(E) ISO 2012 All righ

17、ts reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 13 Terms and definitions . 14 Design characteristics . 14.1 General design and nomenclature . 14.2 Main dimensions . 34.3 Digital indicating display . 44.4 Error messages 44.5 Interface . 44.6 Protection for field

18、 use 44.7 Contact element . 44.8 Zero adjustment . 44.9 Additional functions . 54.10 Design characteristics (manufacturers specification) . 55 Metrological characteristics . 55.1 General . 55.2 Maximum permissible error of indication . 55.3 Maximum permissible limit . 66 Proving of conformance with

19、specification . 67 Marking . 6Annex A (informative) Example of a diagram of errors of indication . 7Annex B (informative) Data sheet (example) . 8Annex C (informative) Calibration of metrological characteristics . 9Annex D (informative) Relation to the GPS matrix model 10Bibliography .12BS EN ISO 13

20、102:2012ISO 13102:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in

21、 a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commiss

22、ion (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical co

23、mmittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not

24、 be held responsible for identifying any or all such patent rights.ISO 13102 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification.iv ISO 2012 All rights reservedBS EN ISO 13102:2012ISO 13102:2012(E)IntroductionThis International Standard

25、 is a Geometrical Product Specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 5 of the chain of standards on size and distance in the general GPS matrix.The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS

26、 system of which this standard is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this standard, and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this standard, unless otherwise indicated.For more detailed information of the rela

27、tion of the standard to other standards and the GPS matrix model, see Annex D. ISO 2012 All rights reserved vBS EN ISO 13102:2012BS EN ISO 13102:2012Geometrical product specifications (GPS) Dimensional measuring equipment: Electronic digital-indicator gauge Design and metrological characteristics1 S

28、copeThis International Standard specifies the most important design and metrological characteristics of electronic digital-indicator gauges.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

29、plies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 14253-1, Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with

30、 specificationsISO 14253-2, Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verificationISO 14978:2006, Geometrical product

31、 specification (GPS) General concepts and requirement for GPS measuring equipmentISO/IEC Guide 98-3, Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)IEC 60529, Degrees of protection provided by enclosures (IP code)3 Terms and definitionsFor the purp

32、oses of this document, the terms and definitions given in ISO 14978, and the following apply.3.1electronic digital-indicator gaugemeasuring instrument in which the axial displacements of a plunger are obtained by a transducer and converted into an electronic signal by suitable electronic means and t

33、ransmitted to a physically integrated digital display4 Design characteristics4.1 General design and nomenclatureThe general design and workmanship shall be such that the performance of the electronic digital-indicator gauge complies with the requirements of this International Standard.The design and

34、 rigidity of the electronic digital-indicator gauge shall be such that the freedom of movement of the plunger is not impaired by clamping the stem of the instrument, providing that such clamping is carried out in a proper manner. Where alternative methods of mounting are provided, e.g. attaching the

35、 lug on the back plate, the design and rigidity of that mounting shall be such that the performance is not impaired.INTERNATIONAL STANDARD ISO 13102:2012(E) ISO 2012 All rights reserved 1BS EN ISO 13102:2012ISO 13102:2012(E)W (uni2259D1)TD1L2D2231L1ZL5467L4D4D5L3Z (2:1)bD385HaKey 1 bezel 5 plunger W

36、 width2 display 6 contact element H height3 operating buttons 7 data output optional T thickness4 stem 8 protection cap optional aOverall dimension.bMeasuring face.See Table 1 for the D and L dimensions.Figure 1 Nomenclature and general design of an electronic digital-indicator gauge2 ISO 2012 All r

37、ights reservedBS EN ISO 13102:2012ISO 13102:2012(E)WD2TL5L1L2HSee Table 1 for the D and L dimensions.Figure 2 Nomenclature and general design of electronic digital-indicator gauge (rectangular type)4.2 Main dimensionsThe electronic digital-indicator gauge shall conform to the dimensions specified in

38、 Figures 1 and 2 and Table 1 to ensure interchangeability. ISO 2012 All rights reserved 3BS EN ISO 13102:2012ISO 13102:2012(E)Table 1 Dimensions of an electronic digital-indicator gaugeValues in millimetresDimension Nominal valueBezel diameter D1()W aStem diameter D28 h6Contact element outside diame

39、ter D3max. 7,5Thread size D4M2,5-6HThread size D5M2,5-6gStem length L1min. 10Length L2b cThread length L3max. 5Thread length L4min. 6Distance L5max. 12aGenerally the diameter of the bezel D1equals the maximal width (W) of the electronic digital-indicator gauge.bL2is the length between the housing an

40、d the end of the plunger if the plunger is pressed in.cDepending on the measuring range.4.3 Digital indicating displayThe design of the digital indication shall be such that the measured values are clearly displayed in any position of the plunger. The unit of measure shall be clearly identified. In

41、the case of negative values the sign shall be indicated.4.4 Error messagesThe electronic digital-indicator gauge shall include means suited for displaying operation- and system-error messages.EXAMPLE Error message caused by excessively rapid plunger movement or insufficient power supply.4.5 Interfac

42、eWhen the unit provides an electronic interface, the manufacturer shall describe the transmission format and protocol of data outputs with as much details as possible.4.6 Protection for field useManufacturers shall clearly indicate, referring to the applicable standard(s), the kind of water and dust

43、 protection (e.g. IP code according to IEC 60529), as well as the type of electromagnetic field protection, if present.4.7 Contact elementThe contact element shall be interchangeable. A selection of elements shall be available. They shall have wear-resistant measuring surfaces and shall be of suitab

44、le form and surface finish allowing the user to select a suitable contact element depending on the measuring task (see Figure 1).4.8 Zero adjustmentEach electronic digital indicator shall be provided with means for setting the indicator to a zero indication in any measuring position.4 ISO 2012 All r

45、ights reservedBS EN ISO 13102:2012ISO 13102:2012(E)4.9 Additional functionsAdditional functions such as counting direction change, value preset and value storage shall be documented by the manufacturer.4.10 Design characteristics (manufacturers specification)As a minimum requirement, the manufacture

46、rs shall specify the design characteristics of the electronic digital-indicator gauge, given in Table 2.Table 2 Design characteristicsCharacteristics Value UnitOverall dimensionsWidthW () D1mmThickness T Height H Measuring range Resolution (equal to the digital step) Height of figures displayed Maxi

47、mum plunger movement speed mm/sPresence of:Data output Yes/No Plunger lifting device Yes/No Attachment mounting and type Yes/No Fluid (water) and dust protectionYesa/No Electromagnetic field protection (if present) Yes/NoRotating display Yes/No Type of power supplyBattery/ ExternalaIP code according

48、 to IEC 60529.5 Metrological characteristics5.1 GeneralThe manufacturer shall specify MPE and MPL information for the metrological characteristics of the electronic digital-indicator gauge which are listed in Table 3. Unless otherwise specified by the manufacturer, the static response of the electro

49、nic digital-indicator gauge shall comply with the MPE/MPL values at any orientation of the gauge.The metrological characteristics of this International Standard apply when the zero or reference point is set at any position within the measuring range.5.2 Maximum permissible error of indication5.2.1 Hysteresis of error of indication (limited by MPEH)Range of the results measured at the same measuring point using both directions of the plunger displacement.5.2.2 Repeatability of error of indication (limited