EN ISO 13259-2018 en Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type jointsBS EN ISO 13259:2018Incorporating corrigendum June 2018National forewordThis

2、 British Standard is the UK implementation of EN ISO 13259:2018. It is identical to ISO 13259:2018. It supersedes BS ISO 13259:2010 and BS EN 1277:2003, which are withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for non-pressure applica

3、tions.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI

4、Standards Limited 2018ISBN 978 0 539 01646 8ICS 23.040.80; 23.040.20; 91.140.80Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigend

5、a issued since publicationDate Text affected30 June 2018 Additional supersession details in National Fore-wordBRITISH STANDARDBS EN ISO 13259:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 13259June 2018ICS 23.040.20; 91.140.80 Supersedes EN 1277:2003EUROPEAN COMMITTEE FOR STANDARDIZATION

6、COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN ISO 13259:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersThermoplastics piping systems for unde

7、rground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints (ISO 13259:2018)Systmes de canalisations en thermoplastiques pour applications enterres sans pression - Mthodes dessai dtanchit des assemblages bague dtanchit en lastomre (ISO 13259:2018)Erdverl

8、egte Rohrleitungssysteme aus Thermoplasten fr drucklose Anwendungen - Prfverfahren fr die Dichtheit von elastomeren Dichtringverbindungen (ISO 13259:2018)This European Standard was approved by CEN on 19 April 2018.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipul

9、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Sta

10、ndard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the nat

11、ional standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Se

12、rbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 13259:2018 (E)European forewordThis document (EN ISO 13259:2018) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” in collaboratio

13、n with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2018, and confl

14、icting national standards shall be withdrawn at the latest by December 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes E

15、N 1277:2003.According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

16、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 13259:2018 has been approved by CE

17、N as EN ISO 13259:2018 without any modification.iiBS EN ISO 13259:2018ISO 13259:2018Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Principle 15 Apparatus . 25.1 General . 25.2 Components of the apparatus 36 Test pieces . 57 Temperature of conditioning and testing . 58 Pro

18、cedure. 58.1 General procedure . 58.2 Procedure for applying diametric deflection to spigot and socket 79 Test report 10 ISO 2018 All rights reserved iiiContents PageBS EN ISO 13259:2018ISO 13259:2018ForewordISO (the International Organization for Standardization) is a worldwide federation of nation

19、al standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internatio

20、nal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended

21、for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.

22、org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will b

23、e in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of

24、 ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Com

25、mittee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage).This second edition cancels and replaces the first edition (ISO 13259:2010), which has been technically revised.Th

26、e main changes compared to the previous edition are as follows: in Clause 7, the temperature conditions are revised; in 8.1, c), in the general procedure, a test at 0 angular deflection is added; in 8.2, in the procedure for applying diametric deflection to spigot and socket, test arrangement for te

27、sting the tightness of couplers/repair collars is added, as well as the related figures.iv ISO 2018 All rights reservedBS EN ISO 13259:2018Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints1 ScopeThis docume

28、nt specifies a test method for determining the leaktightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems.Unless otherwise specified in the referring standard, the tests are carried out at the following basic test pressures: p1: internal negative air

29、pressure (partial vacuum); p2: a low internal hydrostatic pressure; p3: a higher internal hydrostatic pressure.It also describes the following four test conditions under which the tests are performed:a) Condition A: without any additional diametric or angular deflection;b) Condition B: with diametri

30、c deflection;c) Condition C: with angular deflection;d) Condition D: with simultaneous angular and diametric deflection.The applicable selection of the test pressure(s) and the test condition(s) is specified in the referring standard.2 Normative referencesThere are no normative references in this do

31、cument.3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at https:/www.iso

32、.org/obp4 PrincipleA test piece assembled from pipes and/or fittings is subjected to a specific initial internal negative air pressure, p1followed by a low specific initial internal hydrostatic pressure, p2and a higher internal hydrostatic pressure, p3.During testing the joint may be subjected to di

33、ametric and/or angular deflection(s). The referring product standard shall specify which of the test pressures and deflection conditions have to be carried out.INTERNATIONAL STANDARD ISO 13259:2018 ISO 2018 All rights reserved 1BS EN ISO 13259:2018ISO 13259:2018Each pressure is maintained for a spec

34、ific period during which the joint is monitored for leakage (see Clause 8).It is assumed that the following test parameters are set by the referring standard:a) the test pressure(s), p1see 8.1 item e), p2see 8.1 item g) and p3see 8.1 item h), as applicable, and the percentage of loss of partial vacu

35、um see 8.1 item e);b) the required diametric and angular deflections and their combination with each other and/or the test pressure(s).5 Apparatus5.1 GeneralThe apparatus shall consist of a jig or any other arrangement capable of:a) applying the specified diametric and angular deflection;b) applying

36、 the specified test pressure(s), positive or negative;c) maintaining the test assembly in the required position throughout the test;d) resisting the forces resulting from the mass of the water in the test assembly and from the applied hydrostatic test pressure(s) during the test period.The apparatus

37、 shall not otherwise support the joint against the internal test pressure.A typical arrangement, allowing angular and diametric deflection, is shown in Figure 1.2 ISO 2018 All rights reservedBS EN ISO 13259:2018ISO 13259:2018Dimensions in millimetresKey1 vacuum or pressure gauge2 adjustable support3

38、 pipe or fitting with spigot end4 elliptical beam, when applicable5 socket support6 pipe or fitting with sockettotangular deflection appliedb1, b2width of the beam (see 5.2.6 and 5.2.7)F1, F2compressive forceL length of spigot-ended pipe or fitting, where L deor L 1 000, whichever is the greater, in

39、 millimetresL1distance between socket mouth and beamL2distance between the end of pipe and the beam (in contact of the socket), where L2 1 000 for testing pipes only. For testing other components (e.g. inspection chambers, manholes, fittings of large diameters) L2may be reduced.aConnection to pressu

40、re source.Figure 1 Typical arrangement for applying diametric deflection and angular deflection5.2 Components of the apparatusThe apparatus shall include the following items which all shall be capable of resisting the forces and pressures generated during the test.5.2.1 End sealing devices, having a

41、 size and using a sealing method appropriate to seal the non-jointed ends of the test assembly. The devices shall be restrained in a manner that does not exert longitudinal forces on the joint at positive pressures.5.2.2 Hydrostatic pressure source, connected to one of the sealing devices, or to the

42、 test piece, and capable of applying and maintaining the specified pressure see 8.1 items g) and h). ISO 2018 All rights reserved 3BS EN ISO 13259:2018ISO 13259:20185.2.3 Negative air pressure source, connected to one of the sealing devices, or to the test piece, and capable of applying and maintain

43、ing the specified internal negative air pressure for the specified time. See 8.1 item e).5.2.4 Arrangement, capable of venting air from the assembly.5.2.5 Pressure measuring devices, capable of checking conformity to the specified test pressure (see 8.1 items e), g) and h) located at the upper point

44、 of the test assembly.When testing with diametric deflection is required the following items shall also be included.5.2.6 Mechanical or hydraulic device, capable of applying the necessary diametric deflection to the spigot see 8.1 item b) and acting on a beam which is free to move in the vertical pl

45、ane square to the axis of the pipe. For pipes with a diameter equal to or greater than 400 mm, each beam can be elliptically shaped to suit the expected shape of the pipe when deflected as required, see Figure 4. The length of the beam or the curved part of the beam shall be greater than the contact

46、 area with the deflected spigot.The following width, b1, (see Figure 1), shall depend upon the external diameter, de, of the pipe: b1= 100 mm for de 710 mm; b1= 150 mm for 710 mm 1 000 mm.5.2.7 Mechanical or hydraulic device, capable of applying the necessary diametric deflection to the socket see 8

47、.1 item b) and acting on a beam which is free to move in the vertical plane square to the axis of the socket. The length of the beam or the curved part of the beam shall be greater than the contact area with the deflected socket.For pipes with a diameter equal to or greater than 400 mm, each beam ma

48、y be elliptically shaped to suit the expected shape of the socket when deflected as required, see Figure 4.The following width, b2, shall depend upon the external diameter, de, of the pipe: b2= 30 mm for de 110 mm; b2= 40 mm for 110 mm 315 mm.When there is a risk that the stiffening elements (profil

49、es) of a structured wall pipe or socket will deflect more than 0,1 times the profile height, the clamps shall be modified such that they will come into contact with the pipe wall between the profiles when the profile is deflected to between 0,9 times and 0,95 times the profile height (see Figure 2).4 ISO 2018 All rights reservedBS EN ISO 13259:2018ISO 13259:2018Key1 modified loading platehpconstruction heightHpprofile height of the loading plate; 0,9hp Hp 0,95hpFigure 2 Example of modified loading