EN ISO 13385-2-2011 en Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2 Calliper depth gauges Design and metrological characteristics《产品几何技术规范(GP.pdf

1、BSI Standards PublicationBS EN ISO 13385-2:2011Geometrical product specifications (GPS) Dimensional measuringequipmentPart 2: Calliper depth gauges; Designand metrological characteristicsBS EN ISO 13385-2:2011Incorporating corrigendum October 2015BS EN ISO 13385-2:2011 BRITISH STANDARDNational forew

2、ordThis British Standard is the UK implementation of EN ISO 13385-2:2011. It partially supersedes BS 6365:2008.The UK participation in its preparation was entrusted by Technical Committee TDW/4, Technical Product Realization, to Subcommittee TDW/4/4, Technical Product Realization - Gauging and Measu

3、rement Equipment.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Pu

4、blished by BSI Standards Limited 2015ISBN 978 0 580 92210 7ICS 17.040.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2011.Amendments/corrigenda issu

5、ed since publicationDate Text affected31 October 2015 Supersession information in National foreword updatedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13385-2 July 2011 ICS 17.040.30 English Version Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Cal

6、liper depth gauges; Design and metrological characteristics (ISO 13385-2:2011) Spcification gomtrique des produits (GPS) - quipement de mesurage dimensionnel - Partie 2: Jauges de profondeur; caractristiques de conception et caractristiques mtrologiques (ISO 13385-2:2011) Geometrische Produktspezifi

7、kation (GPS) - Lngenmessgerte - Teil 2: Tiefenmessschieber; Konstruktionsmerkmale und messtechnische Anforderungen (ISO 13385-2:2011) This European Standard was approved by CEN on 28 April 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

8、for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in th

9、ree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards b

10、odies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United

11、Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13385-2:201

12、1: EBS EN ISO 13385-2:2011EN ISO 13385-2:2011 (E) 3 Foreword This document (EN ISO 13385-2:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical

13、 product specifications and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withd

14、rawn at the latest by January 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations,

15、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

16、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13385-2:2011 has been approved by CEN as a EN ISO 13385-2:2011 without any modification. BS EN ISO 13385-2:2011EN ISO 13385-2:2011 (E) 3 Foreword Thi

17、s document (EN ISO 13385-2:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specifications and verification” the secretariat of whi

18、ch is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at the latest by January 2012. Attention is drawn to the po

19、ssibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries

20、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

21、 Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13385-2:2011 has been approved by CEN as a EN ISO 13385-2:2011 without any modification. BS EN ISO 13385-2:2011EN ISO 13385-2:2011 (E) 3 Foreword This document (EN ISO 13385-2:2011) has been prepared by Technical

22、Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specifications and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the s

23、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at the latest by January 2012. Attention is drawn to the possibility that some of the elements of this document may be the

24、subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium

25、, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement

26、notice The text of ISO 13385-2:2011 has been approved by CEN as a EN ISO 13385-2:2011 without any modification. BS EN ISO 13385-2:2011ISO 13385-2:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Design char

27、acteristics 2 4.1 General design and nomenclature 2 4.2 Dimensions 3 4.3 Types of indicating devices .3 4.4 Measuring faces 6 5 Metrological characteristics.6 5.1 General .6 5.2 Effect of slider locking6 5.3 Maximum permissible error of indication (limited by MPE)6 5.4 MPE and MPL for a number of me

28、trological characteristics 7 6 Indication in product documentation and data sheets7 7 Proof of conformance with specifications8 7.1 General .8 7.2 Measurement standards for the calibration of metrological characteristics8 8 Marking.8 Annex A (informative) Error tests9 Annex B (informative) Advice on

29、 application.11 Annex C (informative) Data sheet (example)12 Annex D (informative) Calibration of metrological characteristics13 Annex E (informative) Relation to the GPS matrix model.14 Bibliography16 BS EN ISO 13385-2:2011ISO 13385-2:2011(E) iv ISO 2011 All rights reservedForeword ISO (the Interna

30、tional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has be

31、en established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stan

32、dardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies fo

33、r voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or al

34、l such patent rights. ISO 13385-2 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This first edition of ISO 13385-2, together with ISO 13385-1, cancels and replaces ISO 3599:1976 and ISO 6906:1984, which have been technically revis

35、ed. ISO 13385 consists of the following parts, under the general title Geometrical product specifications (GPS) Dimensional measuring equipment: Part 1: Callipers; Design and metrological characteristics Part 2: Calliper depth gauges; Design and metrological characteristics BS EN ISO 13385-2:2011ISO

36、 13385-2:2011(E) ISO 2011 All rights reserved vIntroduction This part of ISO 13385 is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 5 of the chains of standards on size and distance in the general GPS m

37、atrix. The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with

38、this document unless otherwise indicated. For more detailed information on the relation of this part of ISO 13385 to other standards and the GPS matrix model, see Annex E. BS EN ISO 13385-2:2011BS EN ISO 13385-2:2011INTERNATIONAL STANDARD ISO 13385-2:2011(E) ISO 2011 All rights reserved 1Geometrical

39、 product specifications (GPS) Dimensional measuring equipment Part 2: Calliper depth gauges; Design and metrological characteristics 1 Scope This part of ISO 13385 provides the most important design and metrological characteristics of calliper depth gauges: with analogue indication: vernier scale or

40、 circular scale (dial), and with digital indication: digital display. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the cited editions apply. For undated references, the latest edition of the referenced do

41、cument (including any amendments) applies. ISO 14253-1, Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with specifications ISO 14253-2:2011, Geometrical product specifications

42、(GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification ISO 14978:2006, Geometrical product specifications (GPS) General concepts and requirements fo

43、r GPS measuring equipment IEC 60529, Degrees of protection by enclosures (IP Code) ISO/IEC Guide 98-3, Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) ISO/IEC Guide 99, International vocabulary of metrology Basic and general concepts and associated

44、 terms (VIM) BS EN ISO 13385-2:2011ISO 13385-2:2011(E) 2 ISO 2011 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 14978, ISO/IEC Guide 99 and the following apply. 3.1 calliper depth gauge measuring instrument which gives the evalua

45、tion of a dimensional quantity of a step or depth of a feature corresponding to the distance between the end of a beam and the face of a measuring base on the basis of the movement of a slider, moving relative to a measuring scale on a rigid beam See Figure 1. NOTE The indication may be either analo

46、gue (vernier), circular scale or digital. Regarding data transfer, see 4.3.2. 3.2 measuring face contact contact between the measuring face and a feature of a workpiece 3.2.1 partial measuring face contact contact between a partial area of the measuring face and a feature of a workpiece 4 Design cha

47、racteristics 4.1 General design and nomenclature The general design and workmanship of the calliper depth gauges shall be such that its metrological characteristics comply with this part of ISO 13385 under all operational orientations unless otherwise specified by the manufacturer. See Figure 1 for

48、general design. Key 1 beam 5 locking screw 2 slider 6 vernier scale 3 measuring face 7 main scale 4 measuring base ldlength of measuring base Figure 1 Example for a design of a calliper depth gauge (slider with locking screw) BS EN ISO 13385-2:2011ISO 13385-2:2011(E) ISO 2011 All rights reserved 34.

49、2 Dimensions The dimensions of the measuring base which are given in Table 1 are typical dimensions. Table 1 Dimensions of calliper depth gauges Dimensions in millimetres Measuring range up to Typical length, ld, of the measuring base 150 100 200 100 250 100 300 100 to 150 350 100 to 150 500 150 to 250 600 150 to 250 For calliper depth gauges with changeable bases, the following base lengths are preferred: 180 mm, 260 mm, 320 mm. 4.3 Types of indicating devices 4.3.1 General Several types of indicating devices exis