EN ISO 14692-4-2017 en Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4 Fabrication installation and operation.pdf

1、Petroleum and natural gas industries - Glass-reinforced plastics (GRP) pipingPart 4: Fabrication, installation and operation (ISO 14692-4:2017)BS EN ISO 14692-4:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEANSTANDARDNORME EUROPENNE EUROPISCHE NORMEN ISO

2、14692-4 September 2017ICS 75.200; 83.140.30 Supersedes EN ISO 14692-4:2002EnglishVersionPetroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation andoperation (ISO 14692-4:2017)Industries du ptrole et du gaznaturel - Canalisationsen plastique r

3、enforc de verre (PRV) - Partie 4:Construction, installation, inspection et maintenance(ISO 14692-4:2017) Erdl- und Erdgasindustrie - GlasfaserverstrkteKunststoffrohrleitungen (GFK) - Teil 4: Fertigung,Installation und Betrieb (ISO 14692-4:2017)This European Standard was approved by CEN on 22 June 20

4、17.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical referencesconcerning such national standards may be obtained on a

5、pplication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made bytranslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

6、ManagementCentre has the same status as the officialversions.CEN members are the nationalstandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi

7、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue M

8、arnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reservedworldwide for CENnational Members.Ref. No. EN ISO 14692-4:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 14692-4:2017.It is identical to ISO 14692-4:2017. It supersedes

9、 BS EN ISO 14692-4:2002, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PSE/17/-/6, Processing equipment and systems for petroleum and natural gas industries.A list of organizations represented on this committee can be obtained on request to its secre

10、tary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 92674 7ICS 83.140.30; 75.200Compliance with a British Standard

11、 cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 146924:2017EUROPEAN STANDARD NORME EUROPE

12、NNE EUROPISCHE NORM EN ISO 14692-4 September 2017 ICS 75.200; 83.140.30 Supersedes EN ISO 14692-4:2002English Version Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2017) Industries du ptrole et du gaz natu

13、rel - Canalisations en plastique renforc de verre (PRV) - Partie 4: Construction, installation, inspection et maintenance (ISO 14692-4:2017) Erdl- und Erdgasindustrie - Glasfaserverstrkte Kunststoffrohrleitungen (GFK) - Teil 4: Fertigung, Installation und Betrieb (ISO 14692-4:2017) This European Sta

14、ndard was approved by CEN on 22 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning s

15、uch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its o

16、wn language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,

17、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITE

18、E FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14692-4:2017 EBS EN ISO 146924:2017EN ISO 14692-4:2017 (E) 3 European foreword This document (EN

19、 ISO 14692-4:2017) has been prepared by Technical Committee ISO/TC 67 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries“ in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical

20、and natural gas industries” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2018 and conflicting national standards shall be withdrawn at the latest

21、by March 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 14692-4:2002. According to the CEN-CENELEC Internal Re

22、gulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,

23、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 14692-4:2017 has been approved by CEN as EN ISO 14692-4:2017 without any modificatio

24、n. ISO 14692-4:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms, definitions, symbols and abbreviated terms . 14 Fabrication and installation . 24.1 Delivery, inspection and documentation of GRP piping 24.2 Handling and storage. 24.3 System design documentation. 24.4 Instal

25、ler requirements . 34.4.1 Personnel qualification 34.4.2 Health and safety . 34.5 Installation 34.5.1 General requirements 34.5.2 Components fabricated on-site . 44.5.3 Cutting . 44.5.4 Above ground application Supports 44.5.5 Buried piping 54.5.6 Tolerances 54.5.7 Jointing . 74.5.8 Application of f

26、ire-protective coating 84.5.9 Electrical conductivity and electrostatic dissipative properties 94.5.10 Earthing . 94.5.11 Quality programme for installation . 94.6 System testing . 104.6.1 Flushing 104.6.2 Pressure testing .104.7 Certification and documentation . 134.7.1 Flushing certificate .134.7.

27、2 Pressure test certificate 134.8 Inspection . 134.9 Repair after installation . 134.9.1 General. 134.9.2 Repair methods 135 Maintenance and repair .145.1 Maintenance . 145.1.1 General. 145.1.2 Removal of scale and blockages . 145.1.3 Earthing requirements 145.1.4 Surface and mechanical damage . 145

28、.1.5 Fitter and inspector qualification . 145.2 Repair . 145.2.1 General. 145.2.2 Replacement . 155.2.3 Minor repairs .155.2.4 Temporary repair .155.2.5 Quality programme for repair and maintenance 155.3 Modifications and tie-ins . 155.4 Requirements for testing and re-certification 15Annex A (norma

29、tive) Defect types Acceptance criteria and corrective actions 16Annex B (normative) Handling and storage 26 ISO 2017 All rights reserved iiiContents PageBS EN ISO 146924:2017ISO 14692-4:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms, definitions, symbols and abbreviated t

30、erms . 14 Fabrication and installation . 24.1 Delivery, inspection and documentation of GRP piping 24.2 Handling and storage. 24.3 System design documentation. 24.4 Installer requirements . 34.4.1 Personnel qualification 34.4.2 Health and safety . 34.5 Installation 34.5.1 General requirements 34.5.2

31、 Components fabricated on-site . 44.5.3 Cutting . 44.5.4 Above ground application Supports 44.5.5 Buried piping 54.5.6 Tolerances 54.5.7 Jointing . 74.5.8 Application of fire-protective coating 84.5.9 Electrical conductivity and electrostatic dissipative properties 94.5.10 Earthing . 94.5.11 Quality

32、 programme for installation . 94.6 System testing . 104.6.1 Flushing 104.6.2 Pressure testing .104.7 Certification and documentation . 134.7.1 Flushing certificate .134.7.2 Pressure test certificate 134.8 Inspection . 134.9 Repair after installation . 134.9.1 General. 134.9.2 Repair methods 135 Main

33、tenance and repair .145.1 Maintenance . 145.1.1 General. 145.1.2 Removal of scale and blockages . 145.1.3 Earthing requirements 145.1.4 Surface and mechanical damage . 145.1.5 Fitter and inspector qualification . 145.2 Repair . 145.2.1 General. 145.2.2 Replacement . 155.2.3 Minor repairs .155.2.4 Te

34、mporary repair .155.2.5 Quality programme for repair and maintenance 155.3 Modifications and tie-ins . 155.4 Requirements for testing and re-certification 15Annex A (normative) Defect types Acceptance criteria and corrective actions 16Annex B (normative) Handling and storage 26 ISO 2017 All rights r

35、eserved iiiContents PageBS EN ISO 146924:2017ISO 14692-4:2017(E)Annex C (normative) Minimum training requirements for bonder, pipe fitter, spool builder, supervisor and inspector29Annex D (informative) Guidance for use of jointing methods .59Annex E (normative) Electrical conductivity and electrosta

36、tic dissipative properties 68Annex F (informative) Guidance on inspection and NDE methods 70Bibliography .75iv ISO 2017 All rights reservedBS EN ISO 146924:2017ISO 14692-4:2017(E)Annex C (normative) Minimum training requirements for bonder, pipe fitter, spool builder, supervisor and inspector29Annex

37、 D (informative) Guidance for use of jointing methods .59Annex E (normative) Electrical conductivity and electrostatic dissipative properties 68Annex F (informative) Guidance on inspection and NDE methods 70Bibliography .75iv ISO 2017 All rights reserved ISO 14692-4:2017(E)ForewordISO (the Internati

38、onal Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been

39、 established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standa

40、rdization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordanc

41、e with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

42、any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorseme

43、nt.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:

44、 www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems.This second edition cancels and replaces the first edi

45、tion (ISO 14692-4:2002), which has been technically revised. It also incorporates the Technical Corrigendum ISO 14692-4:2002/Cor 1:2006.A list of all parts of ISO 14692 can be found on the ISO website. ISO 2017 All rights reserved vBS EN ISO 146924:2017ISO 14692-4:2017(E)IntroductionThe objective of

46、 this document is to ensure that installed GRP piping systems will meet the specified performance requirements throughout their service life. Main users of the document are envisaged to be the principal, fabrication/installation contractors, repair and maintenance contractors, certifying authorities

47、 and government agencies.vi ISO 2017 All rights reservedBS EN ISO 146924:2017ISO 14692-4:2017(E)IntroductionThe objective of this document is to ensure that installed GRP piping systems will meet the specified performance requirements throughout their service life. Main users of the document are env

48、isaged to be the principal, fabrication/installation contractors, repair and maintenance contractors, certifying authorities and government agencies.vi ISO 2017 All rights reserved Petroleum and natural gas industries Glass-reinforced plastics (GRP) piping Part 4: Fabrication, installation and opera

49、tion1 ScopeThis document gives requirements and recommendations for the fabrication, installation, inspection and maintenance of GRP piping systems for use in oil and natural gas industry processing and utility service applications. The recommendations apply to delivery, inspection, handling, storage, installation, system pressure testing, maintenance and repair.It is intended to be read in conjunction with ISO 14692-1.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of