EN ISO 16584-2002 en Open end blind rivets with break pull mandrel and protruding head - NiCu St or NiCu SSt《带拉断铁心和突头的开端盲铆钉nicu St或nicu sst ISO 16584-2002》.pdf

1、BRITISH STANDARD BS EN ISO 16584:2002 Incorporating Corrigenda Nos. 1 and 2 Open end blind rivets with break pull mandrel and protruding head NiCu/St or NiCu/SSt The European Standard EN ISO 16584:2002 has the status of a British Standard ICS 21.060.40 BS EN ISO 16584:2002 This British Standard, hav

2、ing been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 21 November 2002 BSI 23 November 2004 ISBN 0 580 40775 6 National foreword This British Standard is the official English

3、language version of EN ISO 16584:2002. It is identical with ISO 16584:2002. BS EN ISO 16584:2002, together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002 and BS EN ISO 16585:2002, supersede

4、s BS 7349-2:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee FME/6, Rivets, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards

5、which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publ

6、ication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible internatio

7、nal/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO ti

8、tle page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, the Annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 14313

9、Corrigendum No. 1 24 January 2003 Replacing the EN ISO foreword page and incorporating the Annex ZA page 15327 Corrigendum No. 2 23 November 2004 Addition of supersession detailsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO16584 November2002 ICS21.060.40 Englishversion Openendblindrivetswithb

10、reakpullmandrelandprotruding headNiCu/StorNiCu/SSt(ISO16584:2002) Rivetsaveuglesrupturedetigecorpsouvert,tte bombeNiCu/StouNiCu/SSt(ISO16584:2002) OffeneBlindnietemitSollbruchdornundFlachkopf NiCu/StoderNiCu/SST(ISO16584:2002) ThisEuropeanStandardwasapprovedbyCENon14October2002. CENmembersareboundto

11、complywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropea

12、nStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepubl

13、ic,Denmark,Finland,France,Germany,Greece, Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2002CEN Al

14、lrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO16584:2002ECORRECTED20021218 Foreword Thisdocument(ENISO16584:2002)hasbeenpreparedbyTechnicalCommitteeISO/TC2 “Fasteners“incollaborationwithTechnicalCommitteeCEN/TC185“Threadedandnon threadedmechanicalfas

15、tenersandaccessories“,thesecretariatofwhichisheldbyDIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMay2003,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2003. AccordingtotheCEN/CENELECInternalRegula

16、tions,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg, Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnitedKingdom. Endorsementnoti

17、ce ThetextofISO16584:2002hasbeenapprovedbyCENasENISO16584:2002withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO16584:2002 Reference number ISO 16584:2002(E)INTERNATIONAL STANDARD ISO 16584 First edition 2002-11-01 Open end blind rivets with

18、 break pull mandrel and protruding head NiCu/St or NiCu/SSt Rivets aveugles rupture de tige corps ouvert, tte bombe NiCu/St ou NiCu/SSt ENISO16584:2002ENISO16584:2002ii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO membe

19、r bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmenta

20、l and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directi

21、ves, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies

22、 casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16584 was prepared by Technical Committee ISO/TC 2, Fasteners. Ann

23、ex A of this International Standard is for information only. ENISO16584:2002iiiINTENRATIONAL TSANDADR IS:48561 O2002(E)I SO 2002 All irthgs ersedevr 1Open end blind rivets with break pull mandrel and protruding head NiCu/St or NiCu/SSt 1 Scope This International Standard specifies dimensional and me

24、chanical characteristics and application data for open end blind rivets with break pull mandrel, protruding head, with a nickel copper body (NiCu) and either a steel (St) or stainless steel (SSt) mandrel and with nominal diameters, d, from 3,2 mm up to and including 6,4 mm. 2 Normative references Th

25、e following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this Intern

26、ational Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid Inter

27、national Standards. ISO 3269:2000, Fasteners Acceptance inspection ISO 14588:2000, Blind rivets Terminology and definitions ISO 14589:2000, Blind rivets Mechanical testing 3 Dimensions 3.1 General Symbols and designations of dimensions are specified in ISO 14588. 3.2 Rivets dimensions See Figure 1 a

28、nd Table 1. ENISO16584:20021IS:48561 O2002(E) 2 I SO 2002 All irthgs ersedevrFigure 1 Rivet dimensions Table 1 Rivet dimensions Dimensions in millimetres nom. 3,2 4 4,8 6,4 max. 3,28 4,08 4,88 6,48 d min. 3,05 3,85 4,65 6,25 max. 6,7 8,4 10,1 13,4 d kmin. 5,8 6,9 8,3 11,6 Rivet body k max. 1,3 1,7 2

29、 2,7 d mmax. 2,15 2,75 3,2 3,9 Mandrel p min. 25 27 27 27 Blind length b max. l max+ 4 l max+ 4 l max+ 4,5 l max+ 5,5 Rivet length l nom. = min. max. Recommended grip ranges a 5 6 1 to 3 1 to 3 6 7 2 to 4 8 9 3 to 5 3 to 5 10 11 5 to 7 5 to 7 4 to 6 12 13 7 to 9 7 to 9 6 to 8 3 to 6 14 15 9,0 to 10,

30、5 8 to 10 16 17 10,5 to 12,5 10 to 12 18 19 12,5 to 14,5 12 to 14 6 to 12 20 21 14,5 to 16,5 14 to 16 NOTE The rivet body dimensions are generated from the design formulae specified in annex A. aThe grip ranges of rivets with dimensions as given in Table 1, with the material combination as given in

31、clause 4, are specified by the minimum and maximum grip lengths. The minimum grip lengths are recommendations only. It may be possible to go into individual cases below the minimum values. ENISO16584:20022IS:48561 O2002(E) I SO 2002 All irthgs ersedevr 33.3 Clearance hole diameters The diameters of

32、the clearance holes, d h1 , to accommodate the rivet in the components to be fastened are given in Table 2. Table 2 Clearance hole diameters Dimensions in millimetres d d h1nom. min. max. 3,2 3,3 3,4 4 4,1 4,2 4,8 4,9 5,0 6,4 6,5 6,6 Non conformance to the values listed in Table 2 may result in asse

33、mbly difficulties and/or reduction in the shear and tensile loads specified in Table 3. When necessary, to facilitate alignment, only the component on the access side may have a clearance hole larger than specified in Table 2 (see Figure 2). This may also result in a reduction of the shear and tensi

34、le loads specified in Table 3. aEnlarged clearance hole Figure 2 Enlarged clearance hole to facilitate alignment 4 Material and finish Blind rivets in accordance with this International Standard shall have a rivet body made of nickel copper alloy (NiCu) and a mandrel of either steel (St) or stainles

35、s steel (SSt) and shall have the mechanical properties as specified in clause 5. Material specification is at the descretion of the manufacturer. The surface of the rivet body shall be plain, i.e. in natural finish. ENISO16584:20023IS:48561 O2002(E) 4 I SO 2002 All irthgs ersedevrThe surface finish

36、of the steel mandrel is at the discretion of the manufacturer and may be phosphate and oil or zinc coating. The surface of stainless steel mandrel shall be plain, i.e. in natural finish. 5 Mechanical properties The minimum shear load, minimum tensile load and maximum mandrel break load shall be as s

37、pecified in Table 3 when tested in accordance with ISO 14589. Table 3 Mechanical properties d Shear load Tensile load Mandrel break load nom. min. min. max. mm N N N 3,2 1 400 1 900 4 500 4 2 200 3 000 6 500 4,8 3 300 3 700 8 500 6,4 5 500 6 800 14 700 6 Mandrel push-out resistance The load to push

38、out the mandrel shall exceed 10 N when tested in accordance with ISO 14589. 7 Mandrel head retention capability The portion of the mandrel remaining in the set rivet shall not be ejected by the application of the head retention test load specified in Table 4 when tested in accordance with ISO 14589.

39、 Table 4 Mandrel head retention test loads d nom. mm Head retention test load N 3,2 15 4 20 4,8 25 6,4 30 8 Workmanship Rivets shall be free from burrs and harmful defects and shall have well-formed heads and shanks. After setting, rivets shall not show evidence of cracking when viewed at 5 magnific

40、ation. ENISO16584:20024IS:48561 O2002(E) I SO 2002 All irthgs ersedevr 59 Acceptance testing If there is no other agreement, acceptance inspection in accordance with ISO 3269 applies. 10 Designation EXAMPLE An open end blind rivet, with break pull mandrel and protruding head, with nominal diameter d

41、 = 4 mm and nominal length l = 12 mm with a nickel copper body (NiCu) and a steel mandrel (St) is designated as follows: Blind rivet ISO 16584 - 4 12 - NiCu/St The designation of a rivet with a stainless steel (SSt) mandrel shall follow the above example using /SSt for the last element of the design

42、ation. ENISO16584:20025IS:48561 O2002(E) 6 I SO 2002 All irthgs ersedevrAnnex A (informative) Design formulae A.1 General Blind rivets in accordance with this International Standard comply with the following design formulae and tolerances. A.2 Shank Diameter The maximum shank diameter complies with

43、the formula: d max= d nom+ 0,08 mm The minimum shank diameter complies with the formula: d min= d nom 0,15 mm A.3 Head diameter The maximum head diameter complies with the formula: d k max= 2,1 d nomrounded to one decimal place. A.4 Head diameter tolerance The head diameter tolerance is h16 for d no

44、mu 3,2 mm and h17 for d nom 3,2 mm. A.5 Head height The maximum head height complies with the formula: k max= 0,415 d nomrounded to one decimal place. A.6 Clearance hole diameter The clearance hole diameter for blind rivet application complies with the formulae: d h1 max= d nom+ 0,2 mm d h1 min= d n

45、om+ 0,1 mm ENISO16584:20026AnnexZA (normative) Normativereferencestointernationalpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundatedreference,provisionsfromother publications.Thesenormativereferencesarecitedattheappropriateplacesinthetextandthe publica

46、tionsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisionsof anyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.Forundatedreferencesthelatesteditionofthepublicationreferredto applies(includingamendments). NOTEWhereanInternationalPublicat

47、ionhasbeenmodifiedbycommonmodifications,indicated by(mod.),therelevantEN/HDapplies. Publication Year Title EN Year ISO3269 2000 FastenersAcceptanceinspection ENISO3269 2000 ISO14588 2000 BlindrivetsTerminologyand definitions ENISO14588 2000 ISO14589 2000 BlindrivetsMechanicaltesting ENISO14589 2000 ENISO16584:2002BS EN ISO 16584:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents t