1、BS EN ISO 17635:2016Non-destructive testing of welds - General rules for metallic materials (ISO 17635:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 17635:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO
2、17635:2016. It supersedes BS EN ISO 17635:2010 which iswithdrawn.The UK participation in its preparation was entrusted to Technical Committee WEE/46, Non-destructive testing.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not pu
3、rport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 87064 4 ICS 25.160.40 Compliance with a British Standard cannot confer immunity from legal obli
4、gations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17635 December 2016 ICS 25.160.40 Supe
5、rsedes EN ISO 17635:2010English Version Non-destructive testing of welds - General rules for metallic materials (ISO 17635:2016) Contrle non destructif des assemblages souds - Rgles gnrales pour les matriaux mtalliques (ISO 17635:2016) Zerstrungsfreie Prfung von Schweiverbindungen - Allgemeine Regel
6、n fr metallische Werkstoffe (ISO 17635:2016) This European Standard was approved by CEN on 7 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterat
7、ion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made b
8、y translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
9、 Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDI
10、ZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17635:2016 EBS EN ISO 17635:2016EN ISO 1
11、7635:2016 (E) 3 European foreword This document (EN ISO 17635:2016) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes“ in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which is held by DIN. This European Standard sh
12、all be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2017, and conflicting national standards shall be withdrawn at the latest by June 2017. Attention is drawn to the possibility that some of the elements of this document
13、 may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 17635:2010. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bou
14、nd to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga
15、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 17635:2016 has been approved by CEN as EN ISO 17635:2016 without any modification. BS EN ISO 17635:2016ISO 17635:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms
16、and definitions . 24 Abbreviated terms 35 Limitations 35.1 Stage of manufacture . 35.2 Extent of testing . 35.3 Materials . 36 Personnel qualification . 47 Testing organization . 48 Documentation . 48.1 Documentation prior to testing 48.1.1 Written procedures . 48.1.2 Testing plan 48.2 Documentation
17、 after testing . 48.2.1 Records of individual testing . 48.2.2 Final report . 49 Selection of testing method . 59.1 General . 59.2 Butt- and T-joints with full penetration . 59.3 Butt- and T-joints without full penetration and fillet welds 610 Performance of testing . 610.1 Determination of standard
18、 to be applied . 610.2 Conditions for testing 610.3 Time of testing . 710.4 Non-acceptable indications 7Annex A (normative) Rules and standards to be applied . 8Annex B (informative) Graphs of standard context 11Bibliography .13 ISO 2016 All rights reserved iiiContents PageBS EN ISO 17635:2016ISO 17
19、635:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for
20、 which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on a
21、ll matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. T
22、his document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any o
23、r all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users
24、 and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following UR
25、L: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds.This third edition cancels and replaces the second edition (ISO 17635:2010), which has been technically revised. Notably, it has
26、 been changed as follows: International Standards have replaced European standards as normative references; “examined” has been replaced by “tested” in the whole document; important modifications have been made to Annex A, Rules and standards to be applied; Annex C, Non-acceptable indications, has b
27、een deleted.Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 5 via your national standards body. A complete listing of these bodies can be found at www.iso.org.iv ISO 2016 All rights reservedBS EN ISO 17635:2016I
28、NTERNATIONAL STANDARD ISO 17635:2016(E)Non-destructive testing of welds General rules for metallic materials1 ScopeThis document gives guidelines for the choice of non-destructive testing (NDT) methods for welds and evaluation of the results for quality control purposes, based on quality requirement
29、s, material, weld thickness, welding process and extent of testing.This document also specifies general rules and standards to be applied to the different types of testing, for either the methodology or the acceptance levels for metallic materials.Acceptance levels cannot be a direct interpretation
30、of the quality levels defined in ISO 5817 or ISO 10042. They are linked to the overall quality of the produced batch of welds.Requirements for acceptance levels for NDT comply with quality levels stated in ISO 5817 or ISO 10042 (moderate, intermediate, stringent) only on a general basis and not in d
31、etail for each indication.Annex A gives correlations between quality, NDT and acceptance level standards.Annex B gives an overview of the standards linked to quality levels, acceptance levels and NDT methods.2 Normative referencesThe following documents are referred to in the text in such a way that
32、 some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3452-1, Non-destructive testing Penetrant testing Part 1: Genera
33、l principlesISO 5817, Welding Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) Quality levels for imperfectionsISO 9712, Non-destructive testing Qualification and certification of NDT personnelISO 10042, Welding Arc-welded joints in aluminium and its alloys Qu
34、ality levels for imperfections. ISO 10675-1, Non-destructive testing of welds Acceptance levels for radiographic testing Part 1: Steel, nickel, titanium and their alloysISO 10675-2, Non-destructive testing of welds Acceptance levels for radiographic testing Part 2: Aluminium and its alloysISO 10863,
35、 Non-destructive testing of welds Ultrasonic testing Use of time-of-flight diffraction technique (TOFD)ISO 11666, Non-destructive testing of welds Ultrasonic testing Acceptance levelsISO 13588, Non-destructive testing of welds Ultrasonic testing Use of automated phased array technologyISO 15626, Non
36、-destructive testing of welds Time-of-flight diffraction technique (TOFD) Acceptance levelsISO 17636-1:2013, Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film ISO 2016 All rights reserved 1BS EN ISO 17635:2016ISO 17635:2016(E)ISO 17636-2:2013, Non-de
37、structive testing of welds Radiographic testing Part 2: X- and gamma-ray techniques with digital detectorsISO 17637, Non-destructive testing of welds Visual testing of fusion-welded jointsISO 17638, Non-destructive testing of welds Magnetic particle testingISO 17640, Non-destructive testing of welds
38、 Ultrasonic testing Techniques, testing levels, and assessmentISO 17643, Non-destructive testing of welds Eddy current testing of welds by complex-plane analysisISO 19285, Non-destructive testing of welds Phased Array technique (PA) Acceptance criteriaISO 23277, Non-destructive testing of welds Pene
39、trant testing Acceptance levelsISO 23278, Non-destructive testing of welds Magnetic particle testing Acceptance levelsISO 23279, Non-destructive testing of welds Ultrasonic testing Characterization of indications in welds3 Terms and definitionsFor the purposes of this document, the following terms a
40、nd definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp3.1testing leveldegree of thoroughness and selection of
41、 parameter settings with which a testing method is appliedSOURCE: ISO/TR 25901-1:2016, 2.2.4.5, modified “non-destructive” was deleted from the definition.Note 1 to entry: Different levels correspond to different sensitivities and/or probabilities of detection. The selection of testing levels is nor
42、mally related to the quality requirements.3.2testing organizationinternal or external organization carrying out non-destructive testingSOURCE: ISO/TR 25901-1:2016, 2.2.1.7, modified “destructive testing” was deleted from the definition.3.3indicationrepresentation or signal from a discontinuity in th
43、e format allowed by the non-destructive testing method usedSOURCE: ISO/TR 25901-1:2016, 2.2.4.2, modified “in the format allowed by the non-destructive testing method used” was added to the definition.3.4internal discontinuitydiscontinuity that is not open to a surface or not directly accessible3.5q
44、uality leveldescription of the quality of a weld on the basis of type, size and amount of selected imperfectionsSOURCE: ISO/TR 25901-1:2016, 2.5.172 ISO 2016 All rights reservedBS EN ISO 17635:2016ISO 17635:2016(E)3.6inspection lotgroup of welds which is expected to show a uniform qualityNote 1 to e
45、ntry: Group members can be a part of a weld, a full weld or several welds.Note 2 to entry: The uniform quality can be due to welding procedure applied, material, type of joint, welder, environmental conditions during execution, time period or other items affecting the quality.4 Abbreviated termsFor
46、the purposes of this document, the abbreviated terms given in Table 1 apply.Table 1 Abbreviated termsTesting method AbbreviationEddy current testing ETMagnetic particle testing MTPenetrant testing PTRadiographic testing RTUltrasonic testing UTVisual testing VT5 Limitations5.1 Stage of manufactureThi
47、s document has been prepared for the testing of completed welds (see 10.3). Testing of parent materials prior to welding or between welding sequences is not covered by this document. It is, however, recommended that such testing be performed in accordance with the reference standards for methods and
48、 acceptance levels.5.2 Extent of testingThe extent of testing shall be given in an application standard or defined in a specification.5.3 MaterialsThis document includes requirements for testing of fusion welds in the following materials, their alloys and their combinations:a) steel;b) aluminium;c)
49、copper;d) nickel;e) titanium.The use of this document for other metallic materials shall be specified. ISO 2016 All rights reserved 3BS EN ISO 17635:2016ISO 17635:2016(E)6 Personnel qualificationPersonnel performing NDT and the evaluation of the results for final acceptance of welds shall be qualified in accordance with ISO 9712 or equivalent at an appropriate level in the relevant industrial sector.7 Testing organizationThe testing organization should be
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1