EN ISO 19069-1-2015 en Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1 Designation system and basis for specifications《塑料 甲基丙烯酸甲酯-丙烯腈-丁二烯-苯乙烯共聚物(ABS)模塑和挤塑材料.pdf

1、BSI Standards PublicationBS EN ISO 19069-1:2015Plastics Polypropylene(PP) moulding and extrusionmaterialsPart 1: Designation system and basis forspecificationsBS EN ISO 19069-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 19069-1:2015. It supersedes

2、BS EN ISO 1873-1:1995 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the

3、 necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83159 1 ICS 83.080.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Sta

4、ndard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2015.Amendments/corrigenda issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 19069-1 March 2015 ICS 83.080.20 Supersedes EN ISO 1873-1:1995English Versi

5、on Plastics - Polypropylene (PP) moulding and extrusion materials -Part 1: Designation system and basis for specifications (ISO 19069-1:2015) Plastiques - Matriaux polypropylne (PP) pour moulage et extrusion - Partie 1: Systme de dsignation et base de spcification (ISO 19069-1:2015) Kunststoffe - Po

6、lypropylen (PP)-Formmassen - Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19069-1:2015) This European Standard was approved by CEN on 10 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta

7、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engli

8、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, B

9、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

10、 Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membe

11、rs. Ref. No. EN ISO 19069-1:2015 EBS EN ISO 19069-1:2015EN ISO 19069-1:2015 (E) 3 Foreword This document (EN ISO 19069-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” incollaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This Eu

12、ropean Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by September 2015, and conflicting national standards shall bewithdrawn at the latest by September 2015. Attention is drawn to the possibility that some of the

13、 elements of this document may be the subject of patentrights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1873-1:1995. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the f

14、ollowingcountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, CzechRepublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

15、Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 19069-1:2015 has been approved by CEN as EN ISO 19069-1:2015 without any modification. BS EN ISO 19069-1:2015ISO 19069-1:2015(E)Foreword iv1 Scope . 12

16、Normative references 13 Designation and specification system 23.1 General . 23.2 Data block 1 . 23.3 Data block 2 . 33.4 Data block 3 . 43.5 Data block 4 . 43.5.1 General 43.5.2 Tensile modulus of elasticity . 53.5.3 Charpy impact strength . 53.5.4 Melt mass-flow rate . 63.6 Data block 5 . 64 Exampl

17、es of designations 64.1 Designation only 64.2 Designation transformed into a specification 8Bibliography .10 ISO 2015 All rights reserved iiiContents PageBS EN ISO 19069-1:2015ISO 19069-1:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national st

18、andards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International o

19、rganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for i

20、ts further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/d

21、irectives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in

22、 the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions re

23、lated to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic m

24、aterials.This first edition of ISO 19069-1 cancels and replaces ISO 1873-1:1995, which has been technically revised to introduce a new designation system.ISO 19069 consists of the following parts, under the general title Plastics Polypropylene (PP) moulding and extrusion materials: Part 1: Designati

25、on system and basis for specifications Part 2: Preparation of test specimens and determination of propertiesiv ISO 2015 All rights reservedBS EN ISO 19069-1:2015Plastics Polypropylene (PP) moulding and extrusion materials Part 1: Designation system and basis for specifications1 ScopeThis part of ISO

26、 19069 establishes a system of designation for polypropylene (PP) thermoplastic material, which can be used as the basis for specifications.The types of polypropylene plastics are differentiated from each other by a classification system based on appropriate levels of the designatory propertiesa) te

27、nsile modulus of elasticity,b) impact strength, andc) melt mass-flow rate (MFR),and on information about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.This part of ISO 19069 is applicable to

28、all polypropylene homopolymers and to copolymers of propylene with a content of other 1-olefinic of less than 50 % (m/m), as well as blends of polymers containing at least 50 % (m/m) of aforementioned polymers.It applies to materials ready for normal use in the form of powder, granules, or pellets a

29、nd to materials unmodified or modified by colorants, additives, fillers, etc.This part of ISO 19069 does not apply to propylene-based rubber.It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19069 does not provide engineeri

30、ng data, performance data, or data on processing conditions which can be required to specify a material for a particular application and/or method of processing.If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 19069-21), if sui

31、table.In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements can be given in data block 5 (see 3.1).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are

32、 indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristi

33、cs1) To be published.INTERNATIONAL STANDARD ISO 19069-1:2015(E) ISO 2015 All rights reserved 1BS EN ISO 19069-1:2015ISO 19069-1:2015(E)ISO 1133 (all parts), Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics ISO 1873-22), Plastics Polypropylene

34、(PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties3 Designation and specification system3.1 GeneralThe designation and specification system for thermoplastics is based on the following standardized pattern:DesignationDesignation block (optiona

35、l)Identity blockInternational Stand-ard number blockIndividual-item blockData block 1Data block 2Data block 3Data block 4Data block 5The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individu

36、al-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information.Data block 1: Identification of the plastic by its symbol PP in accordance with ISO 1043-1 and infor-mation about the polymerization process or composition o

37、f the polymer (see 3.2).Data block 2: Fillers or reinforcing materials and their nominal content (see 3.3).Data block 3: Position 1: Intended application or method of processing (see 3.4).Positions 2 to 8: Important properties, additives, and supplementary information (see 3.4).Data block 4: Designa

38、tory properties (see 3.5).Data block 5: For the purpose of specifications, a fifth data block can be added containing addi-tional information (see 3.6).The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas.If a data block is

39、not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).3.2 Data block 1In this data block, after the hyphen, polypropylene plastics are indentified by the symbol “PP”, in accordance with ISO 1043-1, followed by a hyphen and a single code letter giving additional in

40、formation on the polymer as specified in Table 1.2) Will be revised with a new number ISO 19069-2.2 ISO 2015 All rights reservedBS EN ISO 19069-1:2015ISO 19069-1:2015(E)Table 1 Code letters used for additional information in data block 1Code letter DefinitionH Propylene homopolymerBa Thermoplastic p

41、ropylene impact polymer consisting of two or more phases of either a propylene plastic H or a propyl-ene plastic R and rubber phases composed of propylene and another olefinic monomer (or monomers) having no functional group other than the olefinic group, added in situ or physically blended with the

42、 propylene plastic matrix R Thermoplastic propylene random copolymer containing another olefinic monomer (or monomers) having no functional group other than the olefinic group, copolymerized with pro-pyleneaThis group of polymers were termed “block” copolymers in the past.3.3 Data block 2In this dat

43、a block, the type of filler and/or reinforcing material is represented by a single code letter in position 1 and its physical form by a second code letter in position 2, the code letters being as specified in Table 2. Subsequently (without a space), the mass content can be given by a 2-figure number

44、 in positions 3 and 4.Table 2 Code letters for fillers and reinforcing materials in data block 2Code letter Material Code letter FormB Boron B Balls, beads, spheresC CarbonaD PowderF Fibre G Glass G Ground H WhiskersK Calcium carbonate L CelluloseaM Minerala,b,metalaS Synthetic organicaS Scales, fla

45、kesT Talc W Wood X Not specified X Not specified Z OthersaZ OthersaNOTE Mixtures of materials and/or forms can be indicated by combining the relevant codes using the sign “+” and placing the whole between parentheses. For example, a mixture of 25 % glass fibres (GF) and 10 % mineral powder (MD) woul

46、d be indicated by (GF25+MD10).aThese materials can be further defined by their chemical symbol, for example, or additional symbols defined in the relevant International Standard. In the case of metals (M), it is essential to indicate the type of metal by means of its chemical symbol.bMineral fillers

47、 should be designated more precisely if a symbol is available. ISO 2015 All rights reserved 3BS EN ISO 19069-1:2015ISO 19069-1:2015(E)3.4 Data block 3In this data block, information about the intended application and/or method of processing is given in position 1 and information about important prop

48、erties, additives, and colour in positions 2 to 8. The code letters used are specified in Table 3.If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall be inserted in position 1.Table 3 Code letters used in data block 3Code letter Posi

49、tion 1 Code letter Position 2 to 8A Processing stabilized B Blow moulding B Antiblocking C Calendering C Coloured D Powder E Extrusion of pipes, profiles and sheets E Expandable F Extrusion of films F Special burning characteristics G General use G Pellets, granules H Coating H Heat-ageing stabilized J Cable and wire insulating K Cable and wire sheathing K Metal deactivated L Monofilament extrusion L Light or weather stabilized M Injection moulding M Nucleated N Natural (no colour added) P Impact modified Q Compression moulding